Page 1 2009 Chevrolet HHR Owner Manual Seats and Restraint System ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-10 Safety Belts ... 1-13 Child Restraints ... 1-32 Airbag System ... 1-58 Restraint System Check ... 1-79 Features and Controls ... 2-1 Keys ...
Page 2: Canadian Owners
GM reserves the right to make changes after that time without further notice. For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3 Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Page 4: Vehicle Symbol Chart
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. : Airbag Readiness Light : Air Conditioning : Antilock Brake System (ABS) : Audio Steering Wheel Controls or OnStar : Brake System Warning Light "...
Page 5: Seats And Restraint System
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Seat Height Adjuster ...1-3 Power Seat ...1-3 Power Lumbar ...1-4 Heated Seats ...1-4 Reclining Seatbacks ...1-5 Head Restraints ...1-7 Passenger Folding Seatback ...1-8 Rear Seats ...1-10 Split Folding Rear Seat ...1-10 Safety Belts ...1-13 Safety Belts: They Are for Everyone ...1-13 How to Wear Safety Belts Properly ...1-18 Lap-Shoulder Belt ...1-26...
Page 6: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 7: Power Seat
Seat Height Adjuster If your vehicle has this feature, the driver’s seat height adjuster is located on the outboard side of the seat. To raise the seat, move the lever upward repeatedly until the seat is at the desired height. To lower the seat, move the lever downward repeatedly until the seat is at the desired height.
Page 8: Power Lumbar
Power Lumbar If your vehicle has this feature, the control is located on the outboard side of the driver’s seat cushion. To increase support, press and hold the front of the control. To decrease support, press and hold the rear of the control.
Page 9: Reclining Seatbacks
Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 10 CAUTION: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 11: Head Restraints
Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback,...
Page 12: Passenger Folding Seatback
Passenger Folding Seatback Your vehicle has a front passenger seat that folds ﬂat. CAUTION: If you fold the seatback forward to carry longer objects, such as skis, be sure any such cargo is not near an airbag. In a crash, an inﬂating airbag might force that object toward a person.
Page 13 To fold the seatback, do the following: 1. Move the front passenger seat rearward to ensure there is enough room to fold the seatback forward. See Manual Seats on page 1-2 for more information. The head restraint may need to be removed if the seat is not able to be moved fully rearward.
Page 14: Rear Seats
To raise the seatback to an upright position: 1. Pull up on either lever. 2. Push the seatback up until it is in a locked position. CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there.
Page 15 4. Move the safety belt out of the way before lowering the seatback. Do not let the safety belt get caught between the seatback and seat cushion as the seatback is folded. 5. Pull up on the knob located on the top of the seatback on the outboard side to release the seatback.
Page 16 To raise the rear seatback(s): CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear CAUTION: (Continued) 1-12 CAUTION: (Continued)
Page 17: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 18: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-14...
Page 19 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-15...
Page 20 or the instrument panel... 1-16 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 21 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 22: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-32 or Infants and Young Children on page 1-35.
Page 23 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 24 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 1-20 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 25 What is wrong with this? The belt is buckled in the wrong buckle. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 26 What is wrong with this? The belt is over an armrest. 1-22 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 27 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 28 What is wrong with this? The belt is behind the body. 1-24 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 29 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 30: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 31 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Page 32 Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Page 33 There is one guide for each outboard passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip.
Page 34 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 35: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 36: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-32 The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: •...
Page 37 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 38 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 39: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 40 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 41 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 42 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 43: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 44 A forward-facing child seat (B) provides restraint for the child’s body with the harness. 1-40 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window.
Page 45: Securing The Child Within The Child Restraint
Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual.
Page 46: Where To Put The Restraint
Where to Put the Restraint According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;...
Page 47: Lower Anchors And Tethers For Children (Latch)
If the vehicle does not have a rear seat that will accommodate a rear-facing child restraint, a rear-facing child restraint should not be installed in the vehicle, even if the airbag is off. When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle.
Page 48: Top Tether Anchor
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). 1-44 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 49 Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 50 To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. To assist you in locating the top tether anchors, this symbol will be located on the lower side quarter panels for the rear outboard positions, on the storage...
Page 51 Vehicles without Rear Seats — Panel and Rear Seat Delete Models If your vehicle does not have a rear seat, there will be an exposed top tether anchor for the front passenger position located on the rear passenger side pillar behind the front passenger seat.
Page 52: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came...
Page 53 Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
Page 54 2.3. To secure a child in the front passenger position, only if your vehicle does not have rear seats, ﬁnd the top tether anchor located on the rear passenger side pillar behind the front passenger seat. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 55 If the position you are using has an adjustable headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position,...
Page 56 If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 1-42. 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint.
Page 57 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 58: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-42. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Page 59 CAUTION: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
Page 60 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 61 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 62: Airbag System
Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. The vehicle may have the following airbags: • A roof-rail airbag for the driver and the passenger seated directly behind the driver.
Page 63 Here are the most important things to know about the airbag system: CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
Page 64 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 65: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. The right front passenger’s airbag is in the instrument panel on the passenger’s side. 1-61...
Page 66 Driver Side shown, Passenger Side similar If your vehicle has roof-rail airbags for the driver, right front passenger, and second row outboard passengers, they are in the ceiling above the side windows. 1-62 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 67: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 68: How Does An Airbag Restrain
Roof-rail airbags are not intended to inﬂate in frontal impacts, near-frontal impacts, or rear impacts. A roof-rail airbag is intended to deploy on the side of the vehicle that is struck or if the sensing system predicts that the vehicle is about to roll over. In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs...
Page 69: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-rail airbags may still be at least partially inﬂated for some time after they deploy. Some components of the airbag module may be hot for several minutes.
Page 70 In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 71 The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag and roof-rail airbags (if equipped) are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat.
Page 72 If the vehicle does not have a rear seat that will accommodate a rear-facing child restraint, a rear-facing child restraint should not be installed in the vehicle, even if the airbag is off. The passenger sensing system is designed to turn off the right front passenger frontal airbag if: •...
Page 73 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 74 If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. 1-70 If this happens, use the following steps to allow the system to detect that person and enable the right front...
Page 75 Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 76: Passenger Sensing System
Passenger Sensing System (With Turbo and RPO AR9 or AE4) This information is for vehicles with a turbo engine and Regular Production Option (RPO) code AR9 or AE4. RPO codes are listed on the Service Parts Identiﬁcation label. See Service Parts Identiﬁcation Label on page 5-107.
Page 77 CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates and the passenger seat is in a forward position.
Page 78 When the passenger sensing system has turned off the right front passenger frontal airbag, the off indicator will light and stay lit to remind you that the airbag is off. See Passenger Airbag Status Indicator on page 3-31. The passenger sensing system is designed to turn on (may inﬂate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat.
Page 79 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 80 If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. 1-76 If this happens, use the following steps to allow the system to detect that person and enable the right front...
Page 81: Servicing Your Airbag-Equipped Vehicle
Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 82 Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 83: Restraint System Check
Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my airbag system? If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual.
Page 84: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 85: Table Of Contents
Section 2 Keys ...2-3 Remote Keyless Entry (RKE) System ...2-4 Remote Keyless Entry (RKE) System Operation ...2-4 Remote Vehicle Start ...2-7 Doors and Locks ...2-9 Door Locks ...2-9 Power Door Locks ...2-9 Delayed Locking ...2-10 Automatic Door Lock ...2-10 Programmable Automatic Door Unlock ...2-10 Rear Door Security Locks ...2-11 Lockout Protection ...2-12 Rear Side Cargo Door (HHR Panel Only) ...2-12...
Page 86 Section 2 Mirrors ...2-39 Manual Rearview Mirror ...2-39 Automatic Dimming Rearview Mirror ...2-39 Compass ...2-39 Outside Power Mirrors ...2-41 Blind Spot Mirrors ...2-41 Outside Convex Mirror ...2-43 Object Detection Systems ...2-44 Rear Vision Camera (RVC) ...2-44 ® OnStar System ...2-47 Features and Controls Storage Areas ...2-51 Glove Box ...2-51...
Page 87: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 88: Remote Keyless Entry (Rke) System
The key has a bar-coded key tag that the dealer/retailer or qualiﬁed locksmith can use to make new keys. Store this information in a safe place, not in your vehicle. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in.
Page 89 With Remote Start and Remote Rear Doors Shown, Without Similar (Remote Vehicle Start): For vehicles with this feature, press to start the engine from outside the vehicle using the RKE transmitter. See Remote Vehicle Start on page 2-7 for additional information. (Lock): Press to lock all the doors.
Page 90: Battery Replacement
Remote Rear Door Operation (Panel) : Press and hold for about one second to open the rear driver side door. : Press and hold for about one second to open the rear passenger side door. Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work.
Page 91: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote start feature. This feature allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems. See Climate Control System on page 3-21 for additional information. Laws in some local communities may restrict the use of remote starters.
Page 92 If the remote start procedure is used again before the ﬁrst 10 minute time frame has ended, the ﬁrst 10 minutes will immediately expire and the second 10 minute time frame will start. After your vehicle’s engine has been started two times using the remote start button, the vehicle’s ignition switch must be turned to ON/RUN and then back to LOCK/OFF using the key before the remote start...
Page 93: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Page 94: Delayed Locking
Delayed Locking This feature will delay the actual locking of the doors and liftgate when the power door lock switch or remote keyless entry transmitter is used to lock the vehicle. If any door is open when locking the vehicle, three chimes will sound signaling that the delayed locking feature is active.
Page 95: Rear Door Security Locks
Rear Door Security Locks Vehicles with rear door security locks prevent passengers from opening the rear doors from the inside. On vehicles with this feature, the rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them.
Page 96: Lockout Protection
Lockout Protection If you press the power door lock switch when the key is in the ignition and any door is open, all the doors will lock and the driver’s door will unlock. Be sure to remove the key from the ignition when locking your vehicle. The lockout protection can be overridden by pressing and holding the power door lock in the lock position for three seconds.
Page 97 CAUTION: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 98 Manual Liftgate Release To manually open the liftgate, do the following: 1. Remove the trim plug, located on the inside of the liftgate near the center. 2-14 2. Locate the release lever on the latch. The lever is located about three inches (7.62 cm) behind the trim in the access hole.
Page 99 3. Insert a tool into the access hole. Push the release lever rearward. 4. The liftgate will unlatch when the lever is pushed rearward. Push the liftgate to open. 5. Reinstall the trim plug. 2-15...
Page 100: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 101: Power Windows
Power Windows CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Page 102: Sun Visors
Express-Down Window The driver’s window switch has an express-down feature that allows the window to be lowered without holding the switch. Press the switch part way, and the driver’s window will open a small amount. Press the switch down all the way, release it, and the window will go down automatically.
Page 103: Content Theft-Deterrent
Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. Arming the System To arm the system: 1. Turn the ignition off. 2. Press lock on the RKE transmitter. The system will arm after either of the following occur: •...
Page 104: Pass-Key Iii+ Electronic Immobilizer
How the System Alarm is Activated If the system is armed, it can be activated by either: • Opening the driver’s door or tailgate. This causes a 10 second pre-alarm chirp followed by a 30 second full alarm of horn and lights. •...
Page 105: Pass-Key Iii+ Electronic Immobilizer Operation
® PASS-Key III+ Electronic Immobilizer Operation ® Your vehicle has PASS-Key III+ (Personalized Automotive Security System) theft-deterrent system. ® PASS-Key III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system.
Page 106: Starting And Operating Your Vehicle
To program the new key: 1. Verify that the new key has a 2. Insert the already programmed key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key.
Page 107: Ignition Positions
Ignition Positions The ignition switch has four different positions. In order to shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key.
Page 108 (ON/RUN): This is the position in which you can operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The switch stays in this position when the engine is running. If you leave the key in the ACC/ACCESSORY or ON/ RUN position with the engine off, the battery could be drained.
Page 109: Retained Accessory Power (Rap)
3. Locate the plunger. 4. Press and hold the plunger while turning the ignition key to LOCK/OFF. Remove the key. Have the vehicle serviced at your dealer/retailer as soon as possible. Retained Accessory Power (RAP) These vehicle accessories may be used for up to 10 minutes after the engine is turned off.
Page 110: Manual Transmission Operation
Manual Transmission The shift lever should be in N (Neutral) and the parking brake engaged. Hold the clutch pedal down to the ﬂoor and start the engine. The vehicle will not start if the clutch pedal is not all the way down. Starting Procedure 1.
Page 111 Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather condition at or below 0°F (−18°C). Vehicles with am engine coolant heater should be plugged in at least four hours before starting. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0°F (−18°C).
Page 112 Automatic Transmission Operation If the vehicle has an automatic transmission, the shift lever is located on the console between the seats. There are several different positions for the automatic transmission. P (Park): This position locks the front wheels. It is the best position to use when starting the engine because the vehicle cannot move easily.
Page 113 If the vehicle cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and then move the shift lever into another gear.
Page 114 Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-16. I (Intermediate): This position is also used for normal driving. However, it reduces vehicle speed without using the brakes for slight downgrades where the vehicle would otherwise accelerate due to steepness of grade.
Page 115 This is the shift pattern for SS models. Here is how to operate the manual transmission: 1 (First): Press the clutch pedal and shift into 1 (First). Then, slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into 1 (First) when the vehicle is traveling less than 20 mph (32 km/h).
Page 116 Shift Speeds CAUTION: If you skip a gear when you downshift, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift. Up-Shift Light If the vehicle has a manual transmission, there may be an up-shift light.
Page 117: Parking Brake
Parking Brake The parking brake lever is located between the front seats. CAUTION: If the front passenger seat back is folded down, the armrest may make it awkward to grab and pull up the parking brake lever. If the lever is not CAUTION: (Continued) CAUTION: (Continued) pulled up far enough, the vehicle may roll and you...
Page 118: Shifting Into Park (Automatic Transmission)
Shifting Into Park (Automatic Transmission) CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 119: Shifting Out Of Park (Automatic Transmission)
Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park). This is called “torque lock.”...
Page 120: Parking The Vehicle (Manual Transmission)
If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-39 for more information. To shift out of P (Park): 1. Apply the brake pedal. 2.
Page 121: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes).
Page 122: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 123: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use. If the vehicle has map lamps, press the buttons located at the bottom of the mirror to turn them on or off.
Page 124: Compass Calibration
Compass Calibration If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder, or similar object. If CAL appears in the compass window, the compass may need to be reset or calibrated.
Page 125: Outside Power Mirrors
Outside Power Mirrors Controls for the outside power mirrors are located on the driver door armrest. 1. Press the left or right side of the selector switch located beneath the control pad, to select the driver or passenger mirror. 2. Press one of the four buttons located on the control pad to move the mirror to the desired direction.
Page 126 2-42 1. When the approaching vehicle is a long distance away, the image in the main mirror is small and near the inboard edge of the mirror. 2. As the vehicle gets closer, the image in the main mirror gets larger and moves outboard. 3.
Page 127: Outside Convex Mirror
Using the Outside Mirror with the Blind Spot Mirror 1. Set the main mirror so that your vehicle can just be seen and your blind spot mirror has a clear unobstructed view. 2. When checking for traffic or before changing a lane, look at the main driver/passenger side mirror to observe traffic in the adjacent lane, behind your vehicle.
Page 128: Object Detection Systems
Object Detection Systems Rear Vision Camera (RVC) The vehicle may have a Rear Vision Camera system. Read this entire section before using it. CAUTION: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: • Detect objects that are outside the camera’s ﬁeld of view, below the bumper, or underneath the vehicle.
Page 129 Turning the Rear Vision Camera System Off or On To turn off the rear vision camera system, press and hold , located on the inside rearview mirror, until the left indicator light turns off. The rear vision camera display is now disabled. To turn the rear vision camera system on again, press and hold until the left indicator light illuminates.
Page 130 A. View displayed by the camera. B. Corner of the rear bumper. 2-46 When the System Does Not Seem To Work Properly The rear vision camera system might not work properly or display a clear image if: • The RVC is turned off. See “Turning the Rear Camera System On or Off”...
Page 131: Onstar System
The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will ﬂash. • A slow ﬂash may indicate a loss of video signal, or no video signal present during the reverse cycle.
Page 132 Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the ﬁrst prepaid year, contact OnStar to select a monthly or annual subscription payment plan. If a payment plan is not selected, the OnStar system and all services, including airbag notiﬁcation and emergency services, may be deactivated and no longer available.
Page 133: Onstar Virtual Advisor
OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days.
Page 134: How Onstar Service Works
How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy. This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g.
Page 135: Storage Areas
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders There are two cupholders located in the ﬂoor console between the front seats. There is also a cupholder for the rear seat passenger located at the rear of the ﬂoor console.
Page 136: Rear Compartment Storage Panel/Cover
Rear Compartment Storage Panel/Cover Your vehicle may have an adjustable panel/cargo cover feature. The panel/cargo cover can be adjusted into four positions. To use the panel in the ﬁrst position: 1. Insert the front corners of the panel into the lower guides.
Page 137 To use the panel in the second position: 1. Insert the front corners of the panel into the top guides. 2. Slide the panel forward. 3. Press down on the back of the panel to lock it in place. The third position is with the front corners placed in the lower guides and the rear corners placed in the upper guides.
Page 138: Roof Rack System
Roof Rack System Your vehicle may be equipped with a roof rack system. CAUTION: If something is carried on top of the vehicle that is longer or wider than the luggage carrier — like paneling, plywood, or a mattress — the wind can catch it while the vehicle is being driven.
Page 139: Hideaway Rear Storage Bins
Hideaway Rear Storage Bins Your vehicle may have two storage bins located in the rear of the vehicle. Pull up on the handles to open and lift the lid. Use the key to lock/unlock the bins. There is a rod that hooks into place to prop open the lid.
Page 140: Sunroof
Sunroof The vehicle may have a power sunroof. The switches that operate the sunroof are located in the headliner. To open or close the sunroof, the ignition must be in ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active. See Retained Accessory Power (RAP) on page 2-25.
Page 141 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-8 Windshield Washer ...3-9 Rear Window Wiper/Washer ...3-10 Cruise Control ...3-10 Headlamps ...3-14 Wiper Activated Headlamps ...3-15...
Page 142 Section 3 Highbeam On Light ...3-41 Fuel Gage ...3-42 Boost Gage ...3-42 Reconﬁgurable Performance Display (RPD) ...3-43 Driver Information Center (DIC) ...3-48 DIC Operation and Displays ...3-48 DIC Warnings and Messages ...3-50 DIC Vehicle Personalization ...3-56 Audio System(s) ...3-61 Setting the Clock ...3-62 Radio(s) ...3-63 Instrument Panel Using an MP3 ...3-74...
Page 143 ✍ NOTES...
Page 144: Instrument Panel Overview
Instrument Panel Overview...
Page 145 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-24. B. Cruise Control on page 3-10 (If Equipped). C. Turn Signal/Multifunction Lever on page 3-7. D. Instrument Panel Cluster on page 3-27. E. Windshield Wipers on page 3-8 and Windshield Washer on page 3-9.
Page 146: Hazard Warning Flashers
Hazard Warning Flashers (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press again to turn the ﬂashers off. Horn To sound the horn, press the horn symbols located on the steering wheel.
Page 147: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane-Change Signals : Headlamp High/Low-Beam Changer : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following. Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or...
Page 148: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal lever away from you. This indicator light appears on the instrument panel cluster when the high beams are on. To change the headlamps from high beam to low beam, pull the turn signal lever toward you.
Page 149: Windshield Washer
(Delay/Intermittent Speed Sensitive): When the lever is in the delay position, move the intermittent adjust band to set for shorter or longer delay cycles. To the left of the adjust band are bars that indicate the frequency of the wipes. Smaller bars mean the wiper movement is less frequent.
Page 150: Rear Window Wiper/Washer
Rear Window Wiper/Washer The rear window washer/wiper button is located on the instrument panel below the climate controls. CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision.
Page 151: Setting Cruise Control
CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control.
Page 152: Resuming A Set Speed
SET− (Set): Press to set a speed and to decrease the speed. To set a speed do the following: 1. Press to turn cruise control on. The indicator light on the button will come on. 2. Get to the desired speed. 3.
Page 153 Reducing Speed While Using Cruise Control If the cruise control system is already engaged, • Push and hold the SET− button until the lower speed desired is reached, then release it. • To slow down in small amounts, push the SET− button brieﬂy.
Page 154: Headlamps
Headlamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has the following four positions: (Headlamps): Turns on the headlamps, parking lamps, and taillamps. (Parking Lamps): Turns on the parking lamps and taillamps only.
Page 155: Wiper Activated Headlamps
Wiper Activated Headlamps The headlamps and parking lamps are activated 15 seconds after the windshield wipers are turned on. For this feature to work, automatic lighting must be enabled. See Headlamps on page 3-14 for additional information. When the ignition is turned off, the wiper-activated headlamps will immediately turn off.
Page 156: Automatic Headlamp System
Automatic Headlamp System When it is dark enough outside, the automatic system turns on the headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, instrument panel lights, and interior switch backlighting. Do not cover the light sensor, located on top of the instrument panel.
Page 157: Instrument Panel Brightness
Instrument Panel Brightness The control for this feature is located to the right of the steering wheel and above the radio. Move the thumbwheel to the left to dim the lights or to the right to brighten the lights. The dome lamps will turn on when the thumbwheel is moved completely to the right.
Page 158: Electric Power Management
Electric Power Management This vehicle has Electric Power Management (EPM), an advanced control system. It estimates the battery’s temperature and state of charge and then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in.
Page 159: Accessory Power Outlet(S)
Accessory Power Outlet(s) Accessory power outlets can be used to connect electrical equipment, such as a cellular phone. The accessory power outlets are located on the instrument panel below the climate controls and at the rear of the center console. There may be an outlet in the rear cargo area on the passenger side.
Page 160 Rear Power Plug for Converters The vehicle may have a power plug connector located in the rear cargo area on the passenger side behind the service panel. The power connector wiring can be accessed by removing the service panel to begin installation.
Page 161: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter The vehicle may have an ashtray and cigarette lighter. To use the lighter, located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot.
Page 162 (Off): Turn the fan control to this position to turn the fan off. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature. (Fan): Turn clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan runs continuously with the ignition on.
Page 163: Rear Window Defogger
For quick cool down on hot days: 1. Select 2. Select 3. Select 4. Select the coolest temperature. 5. Select the highest fan speed. Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry.
Page 164: Outlet Adjustment
If the vehicle speed is greater than 50 mph (80 km/h) and the rear defogger is on, it remains on as long as the speed is greater than 50 mph (80 km/h). The defogger can also be turned off by turning off the engine. For vehicles with the remote start feature, the rear defogger automatically turns on if it is cold outside.
Page 165 To access the passenger compartment air ﬁlter: 1. Open and empty the glove box. 3. Pull the three tabs of the ﬁlter access door down and open the access door downward. 2. Press both glove box stops outward to let the glove box drop open completely.
Page 166: Warning Lights, Gages, And Indicators
4. Pull the ﬁlter out toward you, keeping it facing upwards. Install the new air ﬁlter with the AIR FLOW arrow pointing downward. Reverse Steps 1 through 4 to reassemble. 3-26 Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 167: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel is left in the fuel tank, and many other things needed to drive safely and economically. United States Manual Transmission Cluster shown, Automatic, SS and Canada similar 3-27...
Page 168: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the speed in both miles per hour (mph) and kilometers per hour (km/h). The vehicle’s odometer works together with the Driver Information Center (DIC). Trip A and Trip B can be set on the odometer. See “Trip Information” under DIC Operation and Displays on page 3-48.
Page 169: Safety Belt Reminders
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more.
Page 170: Airbag Readiness Light
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Page 171: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System (Without Turbo/With Turbo and RPO AS5) on page 1-66 or Passenger Sensing System (With Turbo and RPO AR9 or AE4) on page 1-72 for important safety information. The instrument panel has a passenger airbag status indicator.
Page 172: Charging System Light
Charging System Light This light comes on brieﬂy when the ignition key is turned on, but the engine is not running, as a check to show it is working. It should go out once the engine is running. If it stays on, or comes on while driving, there could be a problem with the charging system or it could indicate that there are problems with a generator drive belt, or that there is an...
Page 173: Brake System Warning Light
Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working well. If the warning light comes on, there is a brake problem.
Page 174: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Page 175: Electronic Stability Control (Esc)/ Traction Control System (Tcs) Indicator/Warning Light
Electronic Stability Control (ESC)/ Traction Control System (TCS) Indicator/Warning Light The Electronic Stability Control (ESC) system or the Traction Control System (TCS) indicator/ warning light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by the dealer/retailer.
Page 176: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light This light comes on brieﬂy while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Page 177: Tire Pressure Light
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on brieﬂy when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is signiﬁcantly underinﬂated.
Page 178 This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required.
Page 179 If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still ﬂashing, follow the previous steps and see your dealer/retailer for service as soon as possible.
Page 180: Oil Pressure Light
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: •...
Page 181: Security Light
This light comes on brieﬂy while starting the engine. If it does not, have the vehicle serviced by your dealer/ retailer. If the system is working normally the indicator light then goes off. If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly.
Page 182: Fuel Gage
Fuel Gage The fuel gage indicates about how much fuel is left in the fuel tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these show a problem with the fuel gage: •...
Page 183: Reconﬁgurable Performance Display (Rpd)
This gage displays the air pressure level in the intake manifold before it enters the engine’s combustion chamber. It is automatically centered at zero every time the engine is started. Actual vacuum or boost is displayed from this zero point. Changes in ambient pressure, such as driving in mountains and changing weather, will slightly change the zero reading.
Page 184 Region A Gage and Speedometer Displays Change the information displayed in Region A by turning the knob either clockwise or counterclockwise. The available gages are: BOOST: Displays positive boost pressure as determined by the manifold air pressure (MAP) sensor. AIR/FUEL RATIO: Displays the mass ratio of air to fuel.
Page 185 Readouts #2 TIRE PRESSURES: Displays the last gage tire pressures recorded from each of the wheel mounted tire pressure sensors. Readouts #3 BAROMETER: Displays ambient air pressure as measured by the engine’s ambient pressure sensor. OUTSIDE TEMPERATURE: Displays ambient temperature as measured by an outside air temperature sensor.
Page 186: Setup Menu
This indicator comes on when Competitive Driving Mode (A) has been set using the traction control switch. This telltale comes on whenever conditions are right for the Launch Mode (B) to activate. See Electronic Stability Control (ESC) on page 4-7 for more information on Competitive Driving Mode and Launch Control.
Page 187 SETUP MENU Options GAUGE APPEARANCE: While the gage is highlighted, press the RPD knob. Then turn the knob to choose the background color for a gage. Press the knob again when gage color is chosen. SHIFT LIGHT SETUP: This screen establishes a RPM range where the shift light comes on for each gear.
Page 188: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization menu modes and warning/status messages. All messages will appear in the DIC display, located at the bottom of the instrument panel cluster.
Page 189 TRIP A or TRIP B Press the information button until TRIP A or TRIP B display. These modes show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time.
Page 190: Dic Warnings And Messages
OIL LIFE Press the information button until OIL LIFE displays. The engine oil life system shows an estimate of the oil’s remaining useful life. It shows 100% when the system is reset after an oil change. It alerts you to change the oil on a schedule consistent with your driving conditions.
Page 191: Brake Fluid
AUTO (Automatic) LIGHTS ON This message displays if the automatic headlamp system is enabled with the headlamp switch. See Automatic Headlamp System on page 3-16 for more information. BRAKE FLUID This message displays, while the ignition is on, when the brake ﬂuid level is low. The brake system warning light on the instrument panel cluster also comes on.
Page 192: Door Ajar
COOLING MODE ON This message may display on some vehicles. Under severe conditions, hot ambient temperatures, steep grades, and towing, your vehicle may experience more transmission shifting. This is temporary and normal under these conditions. This does not require engine or transmission service.
Page 193: Launch Control
ESC (Electronic Stability Control) NOT READY If your vehicle has Electronic Stability Control (ESC), this message may display brieﬂy after starting the vehicle if the system’s sensors are not yet calibrated. The system is not functional until the message stops displaying. Adjust your driving accordingly.
Page 194: Power Steering
LOW FUEL This message displays when your vehicle is low on fuel. Reﬁll the fuel tank as soon as possible. See Fuel Gage on page 3-42, Fuel on page 5-5, and Filling the Tank on page 5-9 for more information. LOW TRACTION If your vehicle has the Enhanced Traction System (ETS) or Traction Control System (TCS), this message displays...
Page 195: Traction Off
If this message turns on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off and then back on. If this message still stays on or turns back on again while you are driving, your vehicle needs service.
Page 196: Dic Vehicle Personalization
DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to a preferred setting. All of the features listed may not be available on your vehicle. Only the features available will be displayed on the DIC. The default settings for the features were set when your vehicle left the factory, but may have been changed from their default state since that time.
Page 197: Remote Start
UNITS This feature allows you to select the units of measurement in which the DIC will display the vehicle information. When UNITS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default in United States): All information will be displayed in English units.
Page 198: Unlock Horn
UNLOCK HORN This feature, which allows the vehicle’s horn to chirp on the ﬁrst press of the unlock button on the Remote Keyless Entry (RKE) transmitter, can be enabled or disabled. When UNLOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp when the unlock...
Page 199 OFF: The doors will lock immediately when pressing the power lock switch or the lock button on the RKE transmitter. See Power Door Locks on page 2-9, Delayed Locking on page 2-10, and Remote Keyless Entry (RKE) System Operation on page 2-4 for more information. To select a setting and move on to the next feature, press the information button while the desired setting is displayed on the DIC.
Page 200 EXT (Exterior) LIGHTS This feature, which allows the vehicle’s exterior perimeter lighting to turn on each time the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on when the unlock button on the RKE transmitter is...
Page 201: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 202: Setting The Clock
Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player To set the time: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press to turn the radio on. 2. Press until the hour begins ﬂashing on the display.
Page 203: Radio(S)
The date does not automatically display. To see the date press while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display. To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1.
Page 204 Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar The vehicle has one of these radios as its audio system. 3-64 Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information.
Page 205: Playing The Radio
Playing the Radio (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. Speed Compensated Volume (SCV): Radios with the Speed Compensated Volume (SCV) feature automatically adjust the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent.
Page 206 ¨ SEEK: Press to seek or scan stations with a strong signal in the selected band. • To seek stations, press and release to the next station and stay there. • To scan stations, press and hold few seconds until the radio beeps once. The radio goes to a station, plays for a few seconds, then goes ¨...
Page 207 FAV (Favorites): A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio favorites page button (FAV button). Press FAV to go through up to six pages of favorites, each having six favorite stations available per page.
Page 208 Storing a Radio Station as a Preset Radios that have numbered pushbuttons store radio stations as presets. Up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered buttons. To store preset stations: 1.
Page 209: Adjusting The Speakers (Balance/Fade)
EQ (Equalization): Press this button to select preset equalization settings. To return to the manual mode, press EQ until Manual displays or start to manually adjust the bass, midrange, or treble by pressing Adjusting the Speakers (Balance/Fade) Depending on which radio the vehicle has, the Balance/Fade can be adjusted using To adjust balance or fade using 1.
Page 210: Radio Messages
Finding a Category (CAT) Station (XM Satellite Radio Service Only) CAT (Category): The radio may have the CAT button feature. To select and ﬁnd a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category tabs on the radio display.
Page 211: Loading A Cd
XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle.
Page 212 FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound is heard at a reduced volume and the elapsed time of the track displays. Release to resume playing the track. RDM (Random): Tracks can be listened to in random, rather than sequential order.
Page 213: Care Of Cds
Care of CDs Store CD(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom of the disc. If the bottom of a CD is damaged it may not play properly or at all. Do not touch the bottom of a CD while handling it.
Page 214: Using An Mp3
CD/AUX (CD/Auxiliary): Press to play a CD while a portable audio device is connected to the auxiliary input. Press again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, No Aux Input Device may display.
Page 215 CD-R or CD-RW Supported File and Folder Structure The radio supports: • Up to 50 folders. • Up to 8 folders in depth. • Up to 50 playlists. • Up to 255 ﬁles. • Playlists with an .m3u or .wpl extension. •...
Page 216 File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the ﬁle name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened.
Page 217 (Previous Folder): Press the softkey below to go to the ﬁrst track in the previous folder. (Next Folder): Press the softkey below to go to the ﬁrst track in the next folder. RDM (Random): MP3 ﬁles can be listened to on a CD in random, rather than sequential order.
Page 218: Connecting A Usb Storage Device ® Or Ipod
Connecting a USB Storage Device ® or iPod The USB Port can be used to control an iPod or a USB storage device. To connect a USB storage device, connect the device to the USB port located on the front of the radio. To connect an iPod, connect one end of the USB cable that came with the iPod to the iPod’s dock connector and connect the other end to the USB port located on the front...
Page 219: Using Softkeys To Control A Usb Storage Device Or Ipod
Using Softkeys to Control a USB Storage Device or iPod The ﬁve softkeys below the radio display are used to control the functions listed below. To use the softkeys: 1. Press the ﬁrst or ﬁfth softkey below the radio display to display the functions listed below, or press the softkey below the function if it is currently displayed.
Page 220 (Music Navigator): Press the softkey below to view and select a ﬁle on an iPod, using the iPod’s menu system. Files are sorted by: • Playlists • Artists • Albums • Genres • Songs • Composers To select ﬁles: 1. Press the softkey below 2.
Page 221: Xm Radio Messages
Shuffle Functionality To use Shuffle: > Press the softkey below between Shuffle Off, Shuffle All Songs/Shuffle Songs, Shuffle Album, or Shuffle Folder. > (Shuffle Off): Press the softkey below shuffle off. This is the default mode when a USB storage device or iPod is ﬁrst connected.
Page 222: Bluetooth
Channel Unavail: This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No Artist Info: No artist information is available at this time on this channel. The system is working properly. No Title Info: No song title information is available at this time on this channel.
Page 223: Voice Recognition
Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise. When to Speak: A short tone sounds after the system responds indicating when it is waiting for a voice command.
Page 224: Pairing A Phone
Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system ﬁrst and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar Calling, if available.
Page 225: Storing Name Tags
Listing All Paired and Connected Phones 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices.
Page 226 Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please”...
Page 227: Deleting Name Tags
3. Say the ﬁrst digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear”...
Page 228: Making A Call
Using the Delete Command The delete command allows speciﬁc name tags to be deleted. To use the delete command: 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag”...
Page 229: Using The Dial Command
Using the Dial Command 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Dial using <phone name>. Number please” followed by a tone. 3. Say the entire number without pausing. •...
Page 230: Receiving A Call
3. Say the name tag of the person to call. • If the system clearly recognizes the name tag it responds with “OK, calling, <name tag>” and dials the number. • If the system is unsure it recognizes the right name tag, it conﬁrms the name tag followed by a tone.
Page 231: Transferring A Call
Three-Way Calling Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press . The system responds with “Ready” followed by a tone. 2. Say “Three-way call”. The system responds with “Three-way call, please say dial or call”.
Page 232: Bluetooth System
To Transfer Audio to the In-Vehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the key is turned to the ON/RUN or ACC/ACCESSORY position.
Page 233: Other Information
Sending a Stored Name Tag During a Call 1. Press . The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. 3.
Page 234: Theft-Deterrent Feature
Theft-Deterrent Feature ® THEFTLOCK is designed to discourage theft of the vehicle’s radio by learning a portion of the Vehicle Identiﬁcation Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle. Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending...
Page 235: Radio Reception
To navigate folders on an iPod or USB device: 1. Press and hold while listening to a song until the contents of the current folder display on the radio display. 2. Press and hold to go back to the previous folder list.
Page 236: Fixed Mast Antenna
XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
Page 237: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-6 Electronic Stability Control (ESC) ...4-7 Traction Control System (TCS) ...4-10 Enhanced Traction System (ETS) ...4-12 Limited-Slip Differential ...4-13...
Page 238: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 239: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 240: Braking
Braking See Brake System Warning Light on page 3-33. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second. But that is only an average.
Page 241: Antilock Brake System (Abs)
Under certain weather or operating conditions, occasional brake squeak, squeal, or other noise might be heard with the vehicle’s performance braking system. The brake system on SS models is designed for superior fade resistance and consistent operation using high performance brake pads. Brake noise and brake dust are normal and do not affect system performance.
Page 242: Brake Assist
Using ABS Do not pump the brakes. Just hold the brake pedal down ﬁrmly and let antilock work. A slight brake pedal pulsation might be felt or some noise noticed, but this is normal. Braking in Emergencies At some time, nearly every driver gets into a situation that requires hard braking.
Page 243: Electronic Stability Control (Esc)
Electronic Stability Control (ESC) The vehicle has an Electronic Stability Control (ESC) system which combines antilock brake, and traction and stability control systems that help the driver maintain directional control of the vehicle in most driving conditions. When the vehicle is started and begins to move, the system performs several diagnostic checks to ensure there are no problems.
Page 244 When the light is on solid and the message(s), SERVICE ESC, ESC OFF, or both display, the system will not assist the driver in maintaining directional control of the vehicle. Adjust your driving accordingly. See DIC Warnings and Messages on page 3-50. The Electronic Stability Control (ESC) system is automatically enabled whenever the vehicle is started.
Page 245: Competitive Driving Mode
Competitive Driving Mode (SS Models Only) The driver can select this optional handling mode by pressing the ESC/TCS button on the console two times quickly. COMPETITIVE MODE will be displayed in the DIC. See DIC Warnings and Messages on page 3-50. Competitive Driving Mode allows the driver to have full control of the front wheels while the ESC system helps maintain directional control of the vehicle by selective...
Page 246: Traction Control System (Tcs)
Traction Control System (TCS) The vehicle has a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the front wheels are spinning too much or are beginning to lose traction.
Page 247 To turn the system off or on, press and release the ESC/TCS button located on the instrument panel. The DIC displays the appropriate message as described previously when the button is pressed. Traction Control Operation Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary.
Page 248: Enhanced Traction System (Ets)
Enhanced Traction System (ETS) The vehicle may have an Enhanced Traction System (ETS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 249: Limited-Slip Differential
If the ETS indicator/warning light comes on and stays on for an extended period of time when the transmission shift lever is in any position other than L (Low), the vehicle may need service. When this light is on solid, the system will not limit wheel spin.
Page 250: Steering
Steering Electric Power Steering If the engine stalls while driving, the power steering assist system will continue to operate until you are able to stop the vehicle. If power steering assist is lost because the electric power steering system is not functioning, the vehicle can be steered but it will take more effort.
Page 251: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 252: Off-Road Recovery
Off-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 253 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Page 254: Racing Or Other Competitive Driving
Racing or Other Competitive Driving See your warranty book before using your vehicle for racing or other competitive driving. After reviewing your warranty book, please see the GM Performance Parts website or catalog and contact the race sanctioning bodies, for example Sports Car Club of America (SCCA) or Grand American, for parts and equipment required for racing or other competitive driving.
Page 255: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water.
Page 256: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 257: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 258: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 259 CAUTION: Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.If the vehicle is stuck in the snow: •...
Page 260: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 4-25. If the vehicle has a traction system, it can often help to free a stuck vehicle.
Page 261: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear, or with a manual transmission, between 1 (First) or 2 (Second) and R (Reverse), spinning the wheels as little as possible.
Page 262 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). 4-26 The tire and loading information label lists the number of occupant seating positions (A), and the...
Page 263 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 264 Example 1 Item Description Maximum Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight = 4-28 Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Maximum Vehicle...
Page 265 Example 3 Item Description Maximum Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight 200 lbs (91 kg) × 5 = Available Cargo Weight = Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight and seating positions.
Page 266 Certiﬁcation Label A vehicle speciﬁc Certiﬁcation/Tire label is found on the rear edge of the driver’s door, or on the vehicle’s center pillar (B-pillar). The label shows the size of your original tires and the inﬂation pressures needed to obtain the gross weight capacity of your vehicle.
Page 267: Towing
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going.
Page 268: Dinghy Towing
Here are some important things to consider before recreational vehicle towing: • What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer’s recommendations. • What is the distance that will be travelled? Some vehicles have restrictions on how far and how long they can tow.
Page 269: Dolly Towing
To prevent the battery from draining while the vehicle is being towed, remove the following fuse from the ﬂoor console fuse block: 8 (Ignition Switch, PASS-Key See Floor Console Fuse Block on page 5-109 for more information. Remember to reinstall the fuse once the destination has been reached.
Page 270: Towing A Trailer (Automatic Transmission)
Towing a Trailer (Automatic Transmission) CAUTION: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 271: Pulling A Trailer
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Page 272: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 273 Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It has a GVWR of 7,200 lbs (3 266 kg), a RGAWR of 4,000 lbs (1 814 kg) and a GCWR (Gross Combination Weight Rating) of 14,000 lbs (6 350 kg).
Page 274: Driving With A Trailer
It is important that the vehicle does not exceed any of its ratings — GCWR, GVWR, RGAWR, Maximum Trailer Rating or Tongue Weight. The only way to be sure it is not exceeding any of these ratings is to weigh the vehicle and trailer.
Page 275: Making Turns
During the trip, check occasionally to be sure that the load is secure, and that the lamps and any trailer brakes are still working. Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer. This can help to avoid situations that require heavy braking and sudden turns.
Page 276: Driving On Grades
Driving on Grades Notice: Do not tow on steep continuous grades exceeding 6 miles (9.6 km). Extended, higher than normal engine and transmission temperatures may result and damage the vehicle. Frequent stops are very important to allow the engine and transmission to cool.
Page 277: Towing A Trailer (Manual Transmission)
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4.
Page 278 ✍ NOTES 4-42...
Page 279: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-6 Fuel E85 (85% Ethanol) ...5-7...
Page 280 Section 5 When It Is Time for New Tires ...5-69 Buying New Tires ...5-70 Different Size Tires and Wheels ...5-71 Uniform Tire Quality Grading ...5-72 Wheel Alignment and Tire Balance ...5-73 Wheel Replacement ...5-73 Tire Chains ...5-74 If a Tire Goes Flat ...5-75 Changing a Flat Tire ...5-76 Removing the Spare Tire and Tools ...5-77 Removing the Flat Tire and Installing the...
Page 281: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes,...
Page 282: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 283: Adding Equipment To The Outside Of The Vehicle
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-18. Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airﬂow around it.
Page 284: Gasoline Speciﬁcations
Gasoline Speciﬁcations At a minimum, gasoline should meet ASTM speciﬁcation D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Additives on page 5-6 for additional information.
Page 285: Fuel E85 (85% Ethanol)
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the speciﬁcations described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels.
Page 286: Fuels In Foreign Countries
At a minimum, E85 should meet ASTM Speciﬁcation D 5798. By deﬁnition, this means that fuel labeled E85 will have an ethanol content between 70% and 85%. Filling the fuel tank with fuel mixtures that do not meet ASTM speciﬁcations can affect driveability and could cause the malfunction indicator lamp to come on.
Page 287: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling.
Page 288 The tethered fuel cap is located behind a hinged fuel door on the passenger side of the vehicle. If the vehicle has E85 fuel capability, the fuel cap will be yellow and state that E85 or gasoline can be used. See Fuel E85 (85% Ethanol) on page 5-7.
Page 289 When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-37.
Page 290: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 291: Hood Release
Hood Release To open the hood, do the following. 1. Pull the interior hood release lever with this symbol on it. It is located to the left of the instrument panel on the driver’s side of the vehicle. 2. Then go to the front of the vehicle and push the secondary hood release lever to the left.
Page 292: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 2.4L engine (2.2L engine similar), here is what you will see: 5-14...
Page 293 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-34. B. Pressure Cap. See Pressure Cap on page 5-32. C. Coolant Recovery Tank. See “Checking Coolant” under Engine Coolant on page 5-27. D. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-23.
Page 294 When you open the hood on the 2.0L L4 engine, this is what you will see: 5-16...
Page 295: Engine Oil
A. Pressure Cap. See Pressure Cap on page 5-32. B. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-23. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-34. D. Coolant Recovery Tank. See “Checking Coolant” under Engine Coolant on page 5-27.
Page 296: When To Add Engine Oil
When to Add Engine Oil If the oil is below the MIN (minimum) mark, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-114.
Page 297: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use For Vehicles With the 2.2L or 2.4L L4 Engine Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness.
Page 298 For Vehicles with the 2.0L L4 Engine Only Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M, such as Mobil 1 equivalent. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard.
Page 299: Cold Temperature Operation
Cold Temperature Operation For Vehicles With the 2.2L or 2.4L L4 Engine If in an area of extreme cold, where the temperature falls below −20°F (−29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures.
Page 300: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 301: Engine Air Cleaner/Filter
Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ﬁlter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water.
Page 302 To inspect or replace the ﬁlter, do the following: 1. Disconnect the Mass Air Flow sensor, PCV hose, and both ducts. 2. Pull the entire system from the top of the engine. 3. Turn the system over and place it on a soft, non-abrasive surface.
Page 303: Automatic Transmission Fluid
To inspect or replace the ﬁlter, do the following: 1. Remove the screws that hold the housing and cover together and lift off the cover. 2. Inspect or replace the engine air cleaner/ﬁlter. 3. Reverse the steps to reinstall the system. Be sure to reinstall the housing tightly.
Page 304: Manual Transmission Fluid
Manual Transmission Fluid It is not necessary to check the manual transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to a dealer/retailer for service. Have it repaired as soon as possible. You may also have the ﬂuid level checked by your dealer/ retailer when the oil is changed.
Page 305: Engine Coolant
CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
Page 306: What To Use
What to Use CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning.
Page 307: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. The coolant recovery tank cap has this symbol on it. The tank is located in the engine compartment toward the front of the engine on the passenger’s side of the vehicle.
Page 308: How To Add Coolant To The Cooling System
How to Add Coolant to the Cooling System CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a speciﬁc coolant ﬁll procedure.
Page 309 If no coolant is visible in the coolant recovery tank, add coolant at the pressure cap as follows: 1. Remove the pressure cap when the cooling system, including the pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise. If you hear a hiss, wait for that to stop.
Page 310: Pressure Cap
8. By this time, the coolant level inside the radiator ﬁller port may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁll port until the level reaches the base of the ﬁll port. 9.
Page 311: If Steam Is Coming From The Engine Compartment
If Steam Is Coming From The Engine Compartment CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 312: Adding Washer Fluid
If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally.
Page 313: Brakes
Brakes Brake Fluid The brake master cylinder and, on manual transmission vehicles, the clutch hydraulic system use the same reservoir. See Engine Compartment Overview on page 5-14 for the location of the reservoir. The reservoir is ﬁlled with DOT 3 brake ﬂuid. There are only two reasons why the brake ﬂuid level in the reservoir might go down: •...
Page 314 What to Add Use only new DOT 3 brake ﬂuid from a sealed container. See Recommended Fluids and Lubricants on page 6-14. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Page 315: Brake Adjustment
Brake Wear This vehicle has front disc brakes and could have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 316: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced —...
Page 317: Jump Starting
Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start the vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 318 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3.
Page 319 Locate the remote negative (−) ground terminal, marked GND (−), which is located at the front of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 5-14 for more information on the location of the positive (+) and negative (−) terminals on the vehicle.
Page 320 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 321 Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 322: Headlamp Aiming
Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim has been preset at the factory and should need no further adjustment. However, if the vehicle is damaged in a crash, the headlamp aim may be affected and adjustment may be necessary.
Page 323 To adjust the vertical aim: 1. Open the hood. See Hood Release on page 5-13 for more information. 2. Find the aim dot on the lens of the low-beam headlamp. 3. Measure the distance from the ground to the aim dot on the low-beam headlamp.
Page 324 Driver Side Shown 7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a 6 mm hex socket. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Page 325: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-51. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 326 To replace the headlamp, turn signal, or parking lamp bulb: 1. Turn the wheel to access the wheel well. 2. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs. 5-48 3. Reach in behind the wheel well liner and locate the bulb to be changed.
Page 327: Center High-Mounted Stoplamp (Chmsl)
Center High-Mounted Stoplamp (CHMSL) To replace the center high-mounted stoplamp bulb: 1. Open the liftgate. See Liftgate on page 2-12. 2. Remove the center trim located near the top of the liftgate. 3. Turn the bulb socket counterclockwise and pull it straight out of the lamps assembly.
Page 328: Taillamps, Turn Signal, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Stoplamps and Back-up Lamps A. Stoplamp/Taillamp/Turn Signal Lamp B. Back-up Lamp 5-50 To replace one of these bulbs: 1. Open the liftgate. See Liftgate on page 2-12. 2. Remove the cover in the rear cargo area of the vehicle to access the bulbs.
Page 329: License Plate Lamp
6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place. 7. Reinstall the cover. License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps to the fascia.
Page 330: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-4 for more information on wiper blade inspection. Replacement blades come in different types and are removed in different ways. For the proper type and length, see Maintenance Replacement Parts on page 6-16.
Page 331: Tires
Backglass Wiper Blade Replacement 1. Remove the protective cap from the wiper arm. If the protective cap is not removed before lifting the wiper arm, the wiper arm could be damaged. 2. Pull the wiper arm away from the backglass and into the service position.
Page 332: Tire Sidewall Labeling
Low-Proﬁle Performance Tire If your vehicle has P225/45R18 size tires, they are classiﬁed as low-proﬁle performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster.
Page 333 (B) TPC Spec (Tire Performance Criteria Speciﬁcation) Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation) Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S.
Page 334 Compact Spare Tire Example (A) Temporary Use Only The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 335 (F) Tire Size A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type, and service description. The letter T as the ﬁrst character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Speciﬁcation) Original equipment tires designed...
Page 336: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 337 GAWR RR Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 4-25. Intended Outboard Sidewall an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) The metric unit for air pressure. Light Truck (LT-Metric) Tire light duty trucks and some multipurpose passenger vehicles.
Page 338 Recommended Inﬂation Pressure manufacturer’s recommended tire inﬂation pressure as shown on the tire placard. See Inﬂation - Tire Pressure on page 5-61 and Loading the Vehicle on page 4-25. Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.
Page 339: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 340: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 341 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inﬂation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
Page 342: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. If your vehicle has this feature, TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly.
Page 343: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 344: Tpms Sensor Matching Process
TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you replace one or more of the TPMS sensors or rotate the vehicle’s tires, the identiﬁcation codes need to be matched to the new tire/wheel location. The sensors are matched, to the tire/wheel locations, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using...
Page 345: Tire Inspection And Rotation
8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the driver side rear tire, and repeat the procedure in Step 5. 9. After hearing the single horn chirp for the driver side rear tire, two additional horn chirps sound to indicate the tire learning process is done.
Page 346 Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-69 and Wheel Replacement on page 5-73. When rotating the vehicle’s tires, always use the correct rotation pattern shown here.
Page 347: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch...
Page 348: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 349: Different Size Tires And Wheels
CAUTION: If you use bias-ply tires on the vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed...
Page 350: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 351: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 352: Tire Chains
If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle.
Page 353: If A Tire Goes Flat
CAUTION: (Continued) Use another type of traction device only if its manufacturer recommends it for use on the vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to the vehicle, drive slowly, readjust or remove the device if it is contacting the vehicle, and do not spin the vehicle’s wheels.
Page 354: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6. CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 355: Removing The Spare Tire And Tools
A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire. Removing the Spare Tire and Tools The jack, wheel wrench, and spare tire are stowed in the rear of the vehicle, underneath the ﬂoor of the cargo area.
Page 356 3. Turn the retainer counterclockwise to remove the tire cover. 4. Remove the tire cover. 5-78 5. Remove the spare tire by placing your hands at the four and eight o’clock positions. Gently pull it up and out of the trunk. See Compact Spare Tire on page 5-98.
Page 357 Turn the plastic wheel nut counterclockwise to loosen the wheel wrench from the jack. Press the button and then pull on the end of the wheel wrench to extend the handle. 5-79...
Page 358: Removing The Flat Tire And Installing The Spare Tire (All Models Except Ss)
Removing the Flat Tire and Installing the Spare Tire (All Models Except SS) 1. Do a safety check before proceeding. See Changing a Flat Tire on page 5-76 for more information. 2. Using the wheel wrench, loosen all the wheel nuts. Do not remove them yet.
Page 359 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 360 5. Remove all the wheel nuts and take off the ﬂat tire. CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident.
Page 361 CAUTION: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 8. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.
Page 362 CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 363: Removing The Flat Tire And Installing The Spare Tire (Ss Model)
Removing the Flat Tire and Installing the Spare Tire (SS Model) The SS Model has larger performance brakes than the base model. The compact spare tire will not clear the front brakes. Do not use the compact spare tire in the event of a front ﬂat tire.
Page 364 3. Position the jack on the rear position and raise the jack lift head to ﬁt over the car ﬂange under the down arrow markings on the rocker panel. 5-86 CAUTION: Getting under a vehicle when it is jacked up is dangerous.
Page 365 4. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to ﬁt underneath the wheel well. 5. Remove all the wheel nuts and take off the tire.
Page 366 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 367 CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 368 To change the front ﬂat tire: Front Tire Changing Procedure 1. Perform a rear tire change by removing the rear tire and installing the compact spare tire in the rear wheel location. The rear road tire will be used to replace the front ﬂat tire. See Rear Tire Changing Procedure in this section.
Page 369 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 370 5. Remove all the wheel nuts and take off the ﬂat tire. 6. Install the tire. 5-92 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 371 7. Remove any rust or dirt from the wheel bolts, mounting surfaces, and wheel. 8. Place the tire on the wheel mounting surface. 9. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each by hand until the wheel is held against the hub.
Page 372: Storing A Flat Or Spare Tire And Tools
CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 373: Storing The Flat Tire And Tools
Storing the Flat Tire and Tools To store the ﬂat tire: 1. Open the liftgate. See Liftgate on page 2-12 for more information. 2. Put back all tools as they were stored in the rear storage compartment and put the compartment cover back on.
Page 374 Aluminum Wheel Steel Wheel 8. Route the hook end of the strap through the wheel. 5-96...
Page 375 9. Attach the strap to the cargo tie-downs in the rear of the vehicle. 10. Slide the buckle to tighten the tie-down strap. Storing the Compact Spare Tire and Tools Use the diagram as a guide for storing the compact spare tire once you are done using it.
Page 376: Compact Spare Tire
4. Secure the jack and wheel wrench (E) with the wing nut (D). 5. With the valve stem up, place the spare tire (C) on the compartment ﬂoor. 6. Make sure the bolt (G) passes through the wheel center. 7. Install the spare tire cover (B). 8.
Page 377: Appearance Care
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery.
Page 378: Fabric/Carpet
Do not clean the vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. • A stiff brush. It can cause damage to the vehicle’s interior surfaces. • Heavy pressure or aggressive rubbing with a cleaning cloth.
Page 379: Leather
4. Continue to gently rub the soiled area until the cleaning cloth remains clean. 5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water. If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary.
Page 380: Instrument Panel, Vinyl, And Other Plastic Surfaces
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces.
Page 381: Washing Your Vehicle
Washing Your Vehicle The best way to preserve the vehicle’s ﬁnish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty.
Page 382: Finish Care
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish. Approved cleaning products can be obtained from your dealer/retailer. If the vehicle has a basecoat/clearcoat paint ﬁnish, the clearcoat gives more depth and gloss to the colored basecoat.
Page 383: Aluminum Or Chrome-Plated Wheels And Trim
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 384: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Page 385: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 386: Electrical System
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer ﬁrst. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 387: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 388 Fuses Fuse Puller Empty Empty Empty Empty 5-110 Usage Fuses Usage Ampliﬁer Cluster Ignition Switch, PASS-Key Stoplamp Heating, Ventilation, Air Conditioning, PASS-Key Empty Spare Airbag Spare Windshield Wiper Climate Control System, Ignition Window Retained Accessory Power Empty Electric Power Steering, Steering Wheel Control Sunroof Spare...
Page 389: Engine Compartment Fuse Block
Fuses Engine Control Module, Transmission Control Module Door Locks Interior Lights Steering Wheel Control Illumination Power Windows Relays Climate Control System Empty Retained Accessory Power (RAP) Engine Compartment Fuse Block The underhood fuse block is located on the driver side of the engine compartment.
Page 390 Fuses Rear Power Plug (Panel Van Only), Cooling Fan (SS only) Empty Air Conditioning Clutch Diode Liftgate, Sunroof Empty Rear Power Outlet (Panel Van Only) Fuel Pump Rear Wiper Mirror Air Conditioning Heated Seats (Option) Fuse Puller Empty Cigarette Lighter Power Outlet Daytime Running Lamps Empty...
Page 391 Fuses Usage Driver Side High-Beam Canister Vent Driver Side Low-Beam Passenger Side Low-Beam Passenger Side High-Beam Parking Lamps Relays Usage Rear Defogger Relay Air Conditioning Clutch Empty Rear Wiper Liftgate Release Fuel Pump Empty Powertrain Daytime Running Lamps Starting System Empty Empty Relays...
Page 392: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Please refer to Maintenance Replacement Parts on page 6-16 for more information. Application Air Conditioning Refrigerant R134a Cooling System 2.0L Engine 2.2L Engine 2.4L Engine with Automatic Transmission 2.4L Engine with Manual Transmission Engine Oil with Filter Fuel Tank...
Page 393 Application Transmission Fluid Automatic (Bottom Pan Removal) Manual — 2.0L L4 Engine (Drain and Reﬁll) Manual — 2.2L L4 or 2.4L L4 Engine (Drain and Reﬁll) Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual.
Page 394 ✍ NOTES 5-116...
Page 395 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-7 Maintenance Footnotes ...6-8 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-10 At Least Once a Year ...6-11 Recommended Fluids and Lubricants ...6-14...
Page 396: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 397 This schedule is for vehicles that: • carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Loading the Vehicle on page 4-25. • are driven on reasonable road surfaces within legal driving limits. • use the recommended fuel.
Page 398: Scheduled Maintenance
Scheduled Maintenance When the CHANGE OIL SOON message displays, service is required for the vehicle. Have the vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 399 Change engine oil and ﬁlter. See Engine Oil on page 5-17. Reset oil life system. See Engine Oil Life System on page 5-21. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). 2.2L and 2.4L engines: Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter.
Page 400 Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components.
Page 401: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 402: Maintenance Footnotes
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings/shoes for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, etc.
Page 403: Owner Checks And Services
(h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 404: Engine Oil Level Check
Engine Oil Level Check Notice: It is important to check the engine oil regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by the vehicle warranty.
Page 405: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Page 406: Ignition Transmission Lock Check
Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface.
Page 407: Underbody Flushing Service
Parking Brake and Automatic Transmission P (Park) Mechanism Check CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 408: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Engine Oil Institute (API) Certiﬁed for Gasoline (2.2L and 2.4L Engines starburst symbol.
Page 409 Usage Fluid/Lubricant ® Automatic DEXRON -VI Automatic Transmission Transmission Fluid. Multi-Purpose Lubricant, Superlube Key Lock (GM Part No. U.S. 12346241, Cylinders in Canada 10953474). Chassis Lubricant Manual (GM Part No. U.S. 12377985, Transmission in Canada 88901242) or lubricant Shift Linkage meeting requirements of NLGI #2, Category LB or GC-LB.
Page 410: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter 2.0L Engine 2.2L and 2.4L Engines Engine Oil Filter Passenger Compartment Air Filter Spark Plugs 2.0L Engine 2.2L and 2.4L Engines Wiper Blades Front –...
Page 411: Engine Drive Belt Routing
Engine Drive Belt Routing Dotted line shows routing for vehicles without air conditioning. 6-17...
Page 412: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 413 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-19...
Page 414 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-20...
Page 415: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-5 Customer Assistance for Text Telephone (TTY) Users ...7-6 Customer Assistance Offices ...7-6 GM Mobility Reimbursement Program ...7-7 Roadside Assistance Program ...7-7 Scheduling Service Appointments ...7-11 Courtesy Transportation ...7-11 Collision Damage Repair ...7-13 Customer Assistance Information...
Page 416: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 417 STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you can ﬁle with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
Page 418 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Page 419: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Chevrolet dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 420: Customer Assistance For Text Telephone (Tty) Users
(2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 421: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000 Long Distance: 011-52-53 29 0 800 GM Mobility Reimbursement...
Page 422: Calling For Assistance
Roadside Assistance is not a part of the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 423: Services Provided
• Emergency Tow From a Public Road or Highway: Tow to the nearest Chevrolet dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow.
Page 424 Services Speciﬁc to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. • Lock-Out Service: Vehicle registration is required. • Trip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route.
Page 425: Scheduling Service Appointments
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience. If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related.
Page 426: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
Page 427: Collision Damage Repair
Additional Program Information All program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for speciﬁc information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described...
Page 428: Repair Facility
Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 429 • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Page 430: Reporting Safety Defects
In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or...
Page 431: Service Manuals
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle.
Page 432: Vehicle Data Recording And Privacy
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Page 433: Onstar
Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) is recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
Page 434 ✍ NOTES 7-20...
Page 435 Accessories and Modiﬁcations ... 5-3 Accessory Power ... 2-25 Accessory Power Outlets ... 3-19 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-78 Additional Required Services, Scheduled Maintenance ... 6-7 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-108 Adjustment Chime Level ... 3-96 Adjustments Headlamp Range ...
Page 436 Appearance Care (cont.) Chemical Paint Spotting ... 5-106 Cleaning Exterior Lamps/Lenses ... 5-103 Fabric/Carpet ... 5-100 Finish Care ... 5-104 Finish Damage ... 5-106 Instrument Panel, Vinyl, and Other Plastic Surfaces ... 5-102 Interior Cleaning ... 5-99 Leather ... 5-101 Sheet Metal Damage ...
Page 437 Bulb Replacement ... 5-51 Center High-Mounted Stoplamp (CHMSL) ... 5-49 Fog Lamp ... 3-16 Halogen Bulbs ... 5-47 Headlamp Aiming ... 5-44 Headlamps ... 5-47 Headlamps, Front Turn Signal, and Parking Lamps ... 5-47 License Plate Lamps ... 5-51 Taillamps, Turn Signal, Stoplamps and Back-up Lamps ...
Page 438 Cleaning Aluminum or Chrome-Plated Wheels ... 5-105 Exterior Lamps/Lenses ... 5-103 Fabric/Carpet ... 5-100 Finish Care ... 5-104 Instrument Panel, Vinyl, and Other Plastic Surfaces ... 5-102 Interior ... 5-99 Leather ... 5-101 Tires ... 5-106 Underbody Maintenance ... 5-106 Washing Your Vehicle ...
Page 439 Display Reconﬁgurable Performance ... 3-43 Doing Your Own Service Work ... 5-4 Dome Lamp ... 3-17 Door Automatic Door Lock ... 2-10 Delayed Locking ... 2-10 Locks ... 2-9 Power Door Locks ... 2-9 Programmable Automatic Door Unlock ... 2-10 Rear Door Security Locks ...
Page 440 Engine Air Cleaner/Filter ... 5-23 Check and Service Engine Soon Lamp ... 3-37 Compartment Overview ... 5-14 Coolant ... 5-27 Coolant Heater ... 2-27 Coolant Temperature Gage ... 3-36 Coolant Temperature Warning Light ... 3-36 Cooling System ... 5-26 Drive Belt Routing ... 6-17 Exhaust ...
Page 441 Fuel ... 5-5 Additives ... 5-6 California Fuel ... 5-6 E85 (85% Ethanol) ... 5-7 Economy Driving ... 4-2 Filling a Portable Fuel Container ... 5-12 Filling the Tank ... 5-9 Fuels in Foreign Countries ... 5-8 Gage ... 3-42 Gasoline Octane ...
Page 442 Heater ... 3-21 Engine Coolant ... 2-27 Height Adjuster, Driver Seat ... 1-3 Hideaway Rear Storage Bins ... 2-55 Highbeam On Light ... 3-41 Highway Hypnosis ... 4-20 Hill and Mountain Roads ... 4-21 Hood Checking Things Under ... 5-12 Release ...
Page 443 Lights ... 3-14 Airbag Readiness ... 3-30 Antilock Brake System (ABS) Warning ... 3-34 Brake System Warning ... 3-33 Charging System ... 3-32 Engine Coolant Temperature Warning ... 3-36 Enhanced Traction System (ETS) Active ... 4-12 Flash-to-Pass ... 3-8 Fog Lamp ... 3-41 Highbeam On ...
Page 444 Message DIC Warnings and Messages ... 3-50 Mirror Reading Lamps ... 3-17 Mirrors Automatic Dimming Rearview ... 2-39 Blind Spot ... 2-41 Manual Rearview Mirror ... 2-39 Outside Convex Mirror ... 2-43 Outside Power Mirrors ... 2-41 MP3 ... 3-74 Navigation System, Privacy ...
Page 445 Paint, Damage ... 5-106 Park Shifting Into ... 2-34 Shifting Out of ... 2-35 Parking Over Things That Burn ... 2-36 Parking Brake ... 2-33 Parking Your Vehicle ... 2-36 Passenger Airbag Status Indicator ... 3-31 Passenger Compartment Air Filter ... 3-24 Passenger Sensing System ...
Page 446 Reconﬁgurable Performance Display (RPD) ... 3-43 Recreational Vehicle Towing ... 4-31 Reimbursement Program, GM Mobility ... 7-7 Remote Keyless Entry (RKE) System ... 2-4 Remote Keyless Entry (RKE) System, Operation ... 2-4 Remote Vehicle Start ... 2-7 Removing the Flat Tire and Installing the Spare Tire ...
Page 447 Security Light ... 3-41 Service ... 5-3 Accessories and Modiﬁcations ... 5-3 Adding Equipment to the Outside of the Vehicle ... 5-5 Doing Your Own Work ... 5-4 Engine Soon Lamp ... 3-37 Publications Ordering Information ... 7-17 Scheduling Appointments ... 7-11 Service Parts Identiﬁcation Label ...
Page 448 Tire Pressure Light ... 3-37 Tires ... 5-53 Aluminum or Chrome-Plated Wheels, Cleaning ... 5-105 Buying New Tires ... 5-70 Chains ... 5-74 Changing a Flat Tire ... 5-76 Cleaning ... 5-106 Compact Spare ... 5-98 Different Size ... 5-71 If a Tire Goes Flat ...
Page 449 Vehicle Control ... 4-3 Loading ... 4-25 Parking Your ... 2-36 Running While Parked ... 2-38 Symbols ... iii Vehicle Data Recording and Privacy ... 7-18 Vehicle Data Recording, Radio Frequency (RFID) ... 7-19 Vehicle Identiﬁcation Number (VIN) ... 5-107 Service Parts Identiﬁcation Label ...
Page 450 Windshield Washer ... 3-9 Washer Fluid ... 5-34 Wiper Blade Replacement ... 5-52 Wiper Blades, Cleaning ... 5-104 Wiper Fuses ... 5-108 Wipers ... 3-8 Winter Driving ... 4-22 Wiper Activated Headlamps ... 3-15 Wipers Rear Washer ... 3-10 XM Radio Messages ... 3-81 XM™...

Chevrolet 2009 HHR Owner's Manual

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Object Detection Systems

Onstar System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2009 HHR

Summary of Contents for Chevrolet 2009 HHR