Page 1 2009 Chevrolet Corvette Owner Manual Seats and Restraint System ... 1-1 Front Seats ... 1-2 Safety Belts ... 1-9 Child Restraints ... 1-25 Airbag System ... 1-44 Restraint System Check ... 1-58 Features and Controls ... 2-1 Keys ... 2-3 Doors and Locks ...
Page 2: Canadian Owners
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3 Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Page 4: Vehicle Symbol Chart
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. : Airbag Readiness Light : Air Conditioning : Antilock Brake System (ABS) : Audio Steering Wheel Controls or OnStar : Brake System Warning Light "...
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Power Seats ...1-3 Power Lumbar and Side Bolsters ...1-3 Heated Seats ...1-4 Memory Seat, Mirrors and Steering Wheel ...1-4 Reclining Seatbacks ...1-6 Seatback Latches ...1-8 Safety Belts ...1-9 Safety Belts: They Are for Everyone ...1-9 How to Wear Safety Belts Properly ...1-14 Lap-Shoulder Belt ...1-22 Safety Belt Use During Pregnancy ...1-24...
Page 6: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 7: Power Seats
Power Seats To adjust a power seat: • Move the control forward or rearward to adjust the seat forward or rearward. • Move the front or rear of the control up or down to adjust the height of the seat cushion. Your seat position can be stored and recalled if you have the memory option.
Page 8: Heated Seats
Heated Seats On vehicles with heated seats, the buttons are located on the center console. The ignition must be on for this feature to work. : Press to turn the seat on at the high setting, and twice to turn it to the low setting. : Press to turn the system off.
Page 9: Easy Exit Seat
For vehicles with the Auto Memory Recall, see “Auto Memory Recall” under DIC Vehicle Personalization on page 3-73 for more information. To stop recall movement of the memory feature, press one of the power seat controls, power mirror or memory buttons, or the telescopic steering column switch.
Page 10: Reclining Seatbacks
Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 11 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 12: Seatback Latches
Seatback Latches To fold a seatback forward, lift the latch located on top of the backside of the seat. The seatback locks when folded down. To return the seatback upright, lift up on the latch and push the seatback rearward. The seatback must be locked in place.
Page 13 Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 14: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-10...
Page 15 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-11...
Page 16 or the instrument panel... 1-12 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 17 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 18: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-25 or Infants and Young Children on page 1-29.
Page 19 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 20 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 1-16 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 21 What is wrong with this? The belt is buckled in the wrong buckle. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 22 What is wrong with this? The belt is over an armrest. 1-18 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 23 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 24 What is wrong with this? The belt is behind the body. 1-20 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 25 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 26: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 27 4. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Page 28: Safety Belt Pretensioners
Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly. They can help tighten the safety belts during the early stages of a moderate to severe frontal and near frontal crash if the threshold conditions for pretensioner activation are met.
Page 29: Child Restraints
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 30: Safety Belts
The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
Page 31 CAUTION: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. 1-27...
Page 32 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 33: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 34 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person’s arms.
Page 35 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat.
Page 36 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 37: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 38 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-34 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the...
Page 39: Convertible Models Only
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 40: Lower Anchors And Tethers For Children
In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. Your vehicle does not have lower anchors or top tether anchors to secure a child restraint with the LATCH system. If a national or local law requires that your top tether be anchored, do not use a child restraint in this vehicle because a top tether cannot be properly anchored.
Page 41 In order to use the top tether anchors in your vehicle, you need a child restraint equipped with a top tether. The child restraint manufacturer will provide you with instructions on how to use the child restraint and its top tether.
Page 42 Top Tether Anchor Locations (Top Tether Anchor): Seating positions with top tether anchors. To assist you in locating the top tether anchors, the top tether anchor symbol is located on the trim cover. 1-38 The top tether anchor is located behind the passenger seat.
Page 43 Securing a Child Restraint with a Top Tether CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with the child...
Page 44: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions. See Passenger Sensing System on page 1-51 and Passenger Airbag Status Indicator on page 3-37 for more information, including important safety information.
Page 45 If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) (Coupe and Convertible Models Only) on page 1-35 or Lower Anchors and Tethers for Children (LATCH) (Z06 and ZR1 Models Only) on page 1-36 for how and where to install the child restraint using LATCH.
Page 46 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 47 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 48: Airbag System
Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. The vehicle may have the following airbags: • A seat-mounted side impact airbag for the driver. •...
Page 49 CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Page 50: Where Are The Airbags
Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. 1-46 The right front passenger frontal airbag is in the instrument panel on the passenger’s side.
Page 51 Driver Side shown, Passenger Side similar If the vehicle has seat-mounted side impact airbags for the driver and right front passenger, they are in the side of the seatbacks closest to the door. CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 52: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 53: What Makes An Airbag Inﬂate
Seat position sensor(s) provide information that is used to determine if the airbags should deploy at a reduced level or at full deployment. Your vehicle may or may not have seat-mounted side impact airbags. See Airbag System on page 1-44. Seat-mounted side impact airbags are intended to inﬂate in moderate to severe side crashes.
Page 54: What Will You See After An Airbag Inﬂates
But airbags would not help in many types of collisions, primarily because the occupant’s motion is not toward those airbags. See When Should an Airbag Inﬂate? on page 1-48 for more information. Airbags should never be regarded as anything more than a supplement to safety belts.
Page 55: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 56 The passenger sensing system will turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions. The driver airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat.
Page 57 The passenger sensing system is designed to turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat.
Page 58 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 59 If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped): 1. Turn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 60: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Your dealer/retailer and the service manual have information about servicing the vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-16.
Page 61 The passenger sensing system may not operate properly if the original seat trim is replaced with non-GM covers, upholstery or trim, or with GM covers, upholstery or trim designed for a different vehicle. Any object, such as an aftermarket seat heater or a comfort enhancing pad or device, installed under or on top of the seat fabric, could also interfere with the operation of the passenger sensing...
Page 62: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 63: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 64 ✍ NOTES 1-60...
Page 65: Features And Controls
Section 2 Keys ...2-3 Keyless Access System ...2-4 Keyless Access System Operation ...2-5 Doors and Locks ...2-10 Door Locks ...2-10 Power Door Locks ...2-12 Automatic Door Lock ...2-13 Programmable Automatic Door Unlock ...2-13 Lockout Protection ...2-13 Hatch ...2-14 Windows ...2-16 Power Windows ...2-17 Sun Visors ...2-18 Theft-Deterrent Systems ...2-18...
Page 66 Section 2 Storage Areas ...2-52 Glove Box ...2-52 Cupholders ...2-52 Center Console Storage ...2-52 Floor Mats ...2-53 Rear Storage Area ...2-53 Convenience Net ...2-55 Cargo Cover ...2-55 Features and Controls Roof Panel ...2-57 Removing the Roof Panel ...2-57 Storing the Roof Panel ...2-60 Installing the Roof Panel ...2-61 Convertible Top ...2-62 Convertible Top (Manual) ...2-62...
Page 67: Keys
Keys CAUTION: Leaving children in a vehicle with the keyless access transmitter is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keyless access transmitter in the vehicle and they could be seriously injured or killed if caught in the path of a...
Page 68: Keyless Access System
The key, located inside the keyless access transmitter, can be used to lock and unlock the glove box and to open the hatch/trunk lid if power to the vehicle is lost. See Hatch on page 2-14 for more information. Press the button (A) near the bottom of the keyless access transmitter to remove the key.
Page 69: Keyless Access System Operation
Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. If there is a decrease in the keyless access transmitter range, try this: • Check the distance. The transmitter may be too far from the vehicle.
Page 70: Keyless Trunk Opening
Keyless Trunk Opening Press the hatch/trunk release button located on the rear of the hatch/trunk lid above the license plate to open the trunk if the keyless access transmitter is within range. See Hatch on page 2-14 for additional information. There are other conditions that can affect the performance of the transmitter.
Page 71: Programming Transmitters To The Vehicle
Programming Transmitters to the Vehicle Only keyless access transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to four transmitters programmed to it.
Page 72: Programming Without A Recognized Transmitter
Programming without a Recognized Transmitter This procedure requires three ten minutes cycles to complete the programming process. United States owners are permitted to program a new transmitter to their vehicle when a recognized transmitter is not available. The Canadian immobilizer standard requires that Canadian owners see their dealer/retailer for programming new transmitters when two recognized transmitters are not available.
Page 73 7. Press Acc. on the ignition switch. 8. The DIC reads WAIT 10 MINUTES and counts down to zero. 9. The DIC displays OFF-ACCESSORY TO LEARN again. 10. Press Acc. on the ignition switch. 11. Steps 8, 9 and 10 will be repeated two more times. 12.
Page 74: Doors And Locks
Battery Replacement Notice: When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter. 1. Separate the transmitter with a ﬂat, thin object inserted into the slot on the side or back of the transmitter.
Page 75 There are several ways to lock and unlock your vehicle. From the outside, press the lock or unlock button on the keyless access transmitter. Door Open to Show Location of Door Handle Sensor When you have the transmitter with you, you may also unlock and open the door by squeezing the door handle sensor (A).
Page 76: Power Door Locks
From outside the vehicle, use the key in the cylinder above the license plate to open the hatch then use the door release tab located on the carpet inside the hatch on the driver’s side of the vehicle. Pull the tab to unlock and unlatch the driver’s door.
Page 77: Automatic Door Lock
Automatic Door Lock The vehicle is programmed so that, when the doors are closed, the ignition is on and the shift lever is moved out of P (Park)for automatic transmissions, or when vehicle speed becomes faster than 8 mph (13 km/h) for manual transmissions, both doors will lock.
Page 78: Hatch
Hatch CAUTION: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 79 Hatch/Trunk Lid Release There are several ways to release the hatch/trunk lid. If your vehicle has an automatic transmission, the shift lever must be in P (Park). For manual transmission vehicles, the parking brake must be set when the ignition is started for the hatch/trunk release to operate. The parking brake does not need to be set when the ignition is off for the hatch/trunk release to operate.
Page 80: Windows
Closing the Rear Compartment (Except Convertible) To close the rear compartment lid of your coupe, pull down on the rear edge of the lid. Lower it until the power pull down latch feature activates and it will close the rest of the way and latch automatically. Emergency Trunk Release Handle (Coupe) Notice: Do not use the emergency trunk release...
Page 81: Power Windows
Power Windows The power window switches are located on each door. Pull up or press down on the front of the switch to raise or lower the window. Retained Accessory Power (RAP) allows you to use the power windows when the ignition is off. For more information, see Retained Accessory Power (RAP) on page 2-24.
Page 82: Sun Visors
Express-Down Window Press the front of the switch to the second position to activate the express-down feature. If you want to stop the window as it is lowering, press the switch again. Window Indexing This feature automatically lowers the window a small amount when the door is opened.
Page 83: Arming The System
Arming the System To arm the system: • Press on the keyless access transmitter. • Open the door and lock the door with the power door lock switch. The security light should ﬂash. Remove the keyless access transmitter from inside the vehicle and close the door.
Page 84: Immobilizer
Immobilizer This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Page 85: Starting And Operating Your Vehicle
If the vehicle does not start and the keyless access transmitter appears to be undamaged, try another keyless access transmitter. Or, place the transmitter in the transmitter pocket. See “NO FOBS DETECTED” under DIC Warnings and Messages on page 3-56 for additional information.
Page 86: Front Air Dam
For the ﬁrst 500 miles/805 km: • Avoid full throttle starts and abrupt stops. • Do not exceed 4,000 engine rpm. • Avoid driving at any one constant speed, fast or slow, including the use of cruise control. • Avoid downshifting to brake or slow the vehicle when the engine speed will exceed 4000 RPM.
Page 87: Ignition Positions
Ignition Positions The vehicle has an electronic keyless ignition with a pushbutton start. In order to shift out of P (Park), the vehicle must be running or in Acc. mode and the regular brake pedal must be applied. (START): Press this button while your foot is on the brake for an automatic transmission, or while pressing in the clutch for a manual transmission, to start the engine.
Page 88: Retained Accessory Power (Rap)
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: • Audio System • Power Windows These features continue to work up to 10 minutes after the engine is turned off or until either door is opened. If a door is opened, the power windows and audio system will shut off.
Page 89: Stopping The Engine
4. If the engine does not start and no DIC message is displayed, wait 15 seconds before trying again to let the cranking motor cool down. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline.
Page 90: Automatic Transmission Operation
Automatic Transmission Operation There are several different positions for the shift lever. P (Park): This position locks the rear wheels. It is the best position to use when starting the engine because the vehicle cannot move easily. 2-26 CAUTION: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set.
Page 91 R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
Page 92 Manual Paddle Shift While in the S (Sport Mode) position, the paddles located on the steering wheel can be used to manually up-shift or down-shift the transmission. While in S (Sport Mode), push the paddle above the steering wheel spokes to up-shift to the next gear, or pull on the paddle behind the steering wheel spokes to down-shift to the next gear.
Page 93 If the vehicle has a Navigation system, see “Head-Up Display (HUD)” in the Index of the navigation manual. The Manual Paddle Shift system will not allow either an up-shift or a down-shift if the vehicle speed is too fast or too slow, nor will it allow a start from 4 (Fourth) or higher gear.
Page 94: Manual Transmission Operation
Manual Transmission Operation This is the shift pattern for the six-speed manual transmission. Here is how to operate the transmission: 1 (First): Press the clutch pedal and shift into 1 (First). Then slowly let up on the clutch pedal as you press the accelerator pedal.
Page 95: Manual Transmission
Shift Speeds (Manual Transmission) CAUTION: If you skip a gear when you downshift, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift. This chart shows when to shift to the next higher gear for the best fuel economy.
Page 96: Parking Brake
Downshifting (Manual Transmission) Do not downshift into the gear shown below at a speed greater than shown in the table: 1 (First) 2 (Second) 74 mph (119 km/h) 3 (Third) 101 mph (163 km/h) 4 (Fourth) 130 mph (209 km/h) Notice: If you skip more than one gear when you downshift, or if you race the engine when you release the clutch pedal while downshifting, you...
Page 97: Shifting Into Park (Automatic Transmission)
Shifting Into Park (Automatic Transmission) CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 98: Shifting Out Of Park
Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park).
Page 99: Parking The Vehicle (Manual Transmission)
If you still are unable to shift out of P (Park): 1. Fully release the shift lever button. 2. While holding down the brake pedal, press the shift lever button again. 3. Move the shift lever to the desired position. If you still cannot move the shift lever from P (Park), consult your dealer/retailer or a professional towing service.
Page 100: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes).
Page 101: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 102: Mirrors
Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror with a compass display and/or ® map lamps, and OnStar . If the vehicle has OnStar, there are three control buttons located at the bottom of ®...
Page 103: Compass Calibration
Compass Calibration Press once to turn the compass display on or off. If after several seconds the display does not show a compass heading, there may be a strong magnetic ﬁeld interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder or similar object.
Page 104: Outside Power Mirrors
Outside Power Mirrors Controls for the outside power mirrors are located on the driver door. To adjust the mirrors: 1. Move the top selector control to the left or right to select either the driver or passenger mirror. 2. Use the arrows located on the four-way control pad to move the mirror in the desired direction.
Page 105: Outside Heated Mirrors
Outside Heated Mirrors < (Rear Window Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-25 for more information. ® OnStar System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services.
Page 106 OnStar Services Available with the Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert •...
Page 107: Onstar Virtual Advisor
OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information.
Page 108: Universal Home Remote System
Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place.
Page 109: Universal Home Remote System Operation
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 3521A-GTV06A.
Page 110 Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
Page 111 3. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button.
Page 112 Programming Universal Home Remote — Fixed Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
Page 113 The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program the Universal Home Remote.
Page 114 3. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.”...
Page 115: Reprogramming Universal Home Remote Buttons
6. After entering all of the switch positions, again, ﬁrmly press and release all three buttons at the same time. The indicator lights turn on. 7. Press and hold the button that will be used to control the garage door until the garage door moves.
Page 116: Storage Areas
Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly.
Page 117: Floor Mats
Floor Mats The ﬂoor mats are designed to remain in position and out of reach of the accelerator pedal. The driver side ﬂoor mat is held in place by two locator pins and the passenger side is held in place by one. Make sure that the driver side ﬂoor mat is properly placed on the ﬂoor so that it does not block the movement of the accelerator pedal.
Page 118 Rear Trunk Partition For vehicles with the power convertible top option only, there is a trunk partition to keep cargo from getting in the way of the convertible top. The trunk partition must be in place for the convertible top to move. If the trunk partition is not properly in place the ATTACH TRUNK PARTITION Driver Information Center (DIC) message displays.
Page 119: Convenience Net
Convenience Net Use the convenience net, located in the rear, to store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Cover For vehicles with this feature, the security shade can provide hidden storage in the rear area of the vehicle.
Page 120 4. Push the loop to the top of the striker (base plate). 3. Grasp the loop at the rear center of the shade and wrap it around the striker assembly. 2-56...
Page 121: Roof Panel
Roof Panel On vehicles with a removable roof panel, follow the procedures when removing or installing it. Removing the Roof Panel CAUTION: Do not try to remove a roof panel while the vehicle is moving. Trying to remove the roof panel while the vehicle is moving could cause an accident.
Page 122 The driver’s side handle moves toward the driver’s 6. To unlock the release latches on the front of the door. The passenger’s side handle moves toward roof panel, grasp each handle and pull it outward. the passenger’s door. 2-58...
Page 123 7. To unlock the rear of the roof panel’s rear release latch, press the back of the release handle (B). Then press the button on the front of the release handle (A). Pull down the latch lever. 8. Stand on one side of the vehicle, and if necessary, have someone stand on the other side.
Page 124: Storing The Roof Panel
Storing the Roof Panel CAUTION: If a roof panel is not stored properly, it could be thrown about the vehicle in a crash or sudden maneuver. People in the vehicle could be injured. Whenever you store a roof panel in the vehicle, always be sure that it is stored securely in the proper location.
Page 125: Installing The Roof Panel
Installing the Roof Panel CAUTION: An improperly attached roof panel may fall into or ﬂy off the vehicle. You or others could be injured. After installing the roof panel, always check that it is ﬁrmly attached by pushing up on the underside of the panel.
Page 126: Convertible Top
Convertible Top Convertible Top (Manual) For care and cleaning of the convertible top, see Convertible Top on page 5-98 under “Service and Appearance Care”. High pressure car washes may cause water to enter the vehicle. If the vehicle has this feature, the following procedures explain the proper operation of the manual convertible top.
Page 127: Lowering The Manual Convertible Top
Notice: Lowering the convertible top when there are objects in the storage area could damage it or break the glass rear window. Always verify that no objects are in the storage area before lowering the convertible top. Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle.
Page 128 5. Lift upward on the front edge (A) of the convertible top off of the windshield frame. Then lift upward on the rear edge (B) of the convertible top so it is vertical to the tonneau cover (C). The front edge (A) and rear edge (B) should be straight up.
Page 129 After pressing the release button, the driver’s and passenger’s door glass should retract to the full-down position. If the vehicle has lost battery power, the tonneau cover (C) can still be opened using the manual release cable. The tonneau cover emergency manual release cable is located underneath the carpeting behind the passenger’s seat head restraint, on the underside forward edge of the tonneau cover.
Page 130 8. Push forward on the front edge (A) of the convertible top to allow the rear edge (B) of the convertible top to be moved to its full-down position. 2-66 9. Then move the top rearward to its fully-stored position. 10.
Page 131 Raising the Manual Convertible Top 1. Park on a level surface. Shift an automatic transmission into P (Park) and set the parking brake. Shift a manual transmission into N (Neutral) and set the parking brake. 2. Lower both windows. 3. Make sure the ignition is off. 4.
Page 132 7. Lift the rear edge (B) of the convertible top to its full-up position by ﬁrst raising the front edge (A). 8. Close the tonneau cover (C) by pushing it down with a swift, ﬁrm motion. 9. Lower the rear edge (B) of the convertible top by ﬁrst slightly pushing the front edge (A) of the convertible top forward.
Page 133: Convertible Top (Power)
Convertible Top (Power) For care and cleaning of the convertible top see Convertible Top on page 5-98 under “Service and Appearance Care”. High pressure car washes may cause water to enter the vehicle. To operate the power convertible top use the following steps.
Page 134 3. Release the convertible top front latch, located above the inside rearview mirror, by pulling and turning it clockwise toward the driver’s door. Push upward on the front edge. The windows will automatically lower. 2-70 4. Push and hold the bottom of the power convertible top button, located to the left of the...
Page 135 Raising the Power Convertible Top Notice: If you raise or lower the convertible top while the vehicle is in motion, you could damage the top or the top mechanism. The repairs would not be covered by your warranty. Always put an automatic transmission in (P) Park or a manual transmission in (N) Neutral before raising or lowering the convertible top.
Page 136 If the radio is on the sound may be muted for a brief time due to a new audio system equalization being loaded. If the vehicle has lost power, the convertible top can still be raised by releasing pressure on the hydraulic pump, located under the passenger’s side of the tonneau cover, by using the following steps.
Page 137 2. Locate the pressure release bolt on the front side of the hydraulic pump. 3. Use the wrench, located in the console, and turn the pressure release bolt counterclockwise one revolution, to relieve pressure to the hydraulic pump. This will allow you to manually raise the convertible top.
Page 138 ✍ NOTES 2-74...
Page 139 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals (Auto Signal) ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-9 Windshield Washer ...3-10 Cruise Control ...3-10 Exterior Lamps ...3-14 Wiper Activated Headlamps ...3-15 Headlamps on Reminder ...3-15...
Page 140 Section 3 Highbeam On Light ...3-48 Fuel Gage ...3-49 Boost Gage (ZR1 Only) ...3-50 Driver Information Center (DIC) ...3-50 DIC Operation and Displays ...3-50 DIC Warnings and Messages ...3-56 Other Messages ...3-72 DIC Vehicle Personalization ...3-73 Audio System(s) ...3-82 Setting the Clock ...3-82 Radio(s) ...3-83 Instrument Panel Using an MP3 ...3-94...
Page 141 ✍ NOTES...
Page 142: Instrument Panel Overview
Instrument Panel Overview...
Page 143 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-30. B. Head-Up Display (HUD) on page 3-20 (If Equipped). C. Turn Signal/Multifunction Lever on page 3-7. Cruise Control on page 3-10. Fog Lamps on page 3-17.
Page 144: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers warns others that you have a problem. The button is located near the center of the instrument panel. : Press to make the front and rear turn signal lamps ﬂash on and off. Press again to turn the ﬂashers off. The hazard warning ﬂashers work no matter what mode the ignition is in, even if the ignition is turned off.
Page 145: Turn Signal/Multifunction Lever
Telescopic Steering Column If your vehicle has this feature, the telescopic steering column will allow you to adjust the distance the steering wheel is from the instrument panel. The telescopic steering column switch is located on the right side of the steering column.
Page 146: Turn And Lane-Change Signals (Auto Signal)
Turn and Lane-Change Signals (Auto Signal) An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change.
Page 147: Windshield Wipers
Windshield Wipers The windshield wiper lever is located on the right side of the steering column. Move the lever to the following positions: (High Speed): For steady wiping at high speed. (Low Speed): For steady wiping at low speed. & (Delay): Use to set a delay between wipes.
Page 148: Windshield Washer
Windshield Washer The lever on the right side of the steering column also controls the windshield washer. There is a button at the end of the lever. To spray washer ﬂuid on the windshield, press the button and hold it. The washer will spray until you release the button.
Page 149: Setting Cruise Control
The vehicle has cruise control. (Off): Turns the system off. (On): Turns the system on. + (Resume/Accelerate): Use to make the vehicle accelerate or resume a previously set speed. (Set): Press this button at the end of the lever to set the speed.
Page 150: Resuming A Set Speed
Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged. But it does not need to be reset. Once the vehicle is going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from The vehicles goes back up to your chosen speed and...
Page 151 Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle slows down to the cruise control speed set earlier. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle’s speed, load, and the steepness of the hills.
Page 152: Exterior Lamps
Ending Cruise Control To end a cruise control session, step lightly on the brake pedal. If the vehicle has a manual transmission, lightly tapping the clutch will also end a cruise control session. Move the cruise control switch to completely off. When cruise control is disengaged, the CRUISE DISENGAGED message displays on the Driver Information Center (DIC).
Page 153: Wiper Activated Headlamps
AUTO (Automatic): Sets the exterior lamps to automatic mode. AUTO mode turns the exterior lamps on and off depending on how much light is available outside the vehicle. To override AUTO mode, turn the control to off. To reset to AUTO mode turn the control to exterior lamps and then back to AUTO.
Page 154: Daytime Running Lamps (Drl)
Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system makes the front turn signal lamps come on when the following conditions are met: •...
Page 155: Fog Lamps
Fog Lamps Use fog lamps for better vision in foggy or misty conditions. The fog lamps control is located on the multifunction lever next to the exterior lamp control. (Fog Lamps): Turning the band to this position will turn the fog lamps on. When you turn the fog lamps on, the fog lamp light will appear on the instrument panel cluster to indicate that the fog lamps and the parking lamps are on.
Page 156: Exterior Lighting Battery Saver
You can idle the vehicle with the lamps off, even when it is dark outside. After starting the vehicle, turn the exterior lamp control band on the multifunction lever to off and then release it. The lamps will remain off until the control band is turned to off again.
Page 157: Instrument Panel Brightness
Instrument Panel Brightness The knob for this feature is located on the left side of the instrument panel. Push the knob in to turn on the interior lights. Turn and hold the knob clockwise to brighten the lights or counterclockwise to dim them. During the day, this knob will adjust the instrument panel brightness and at night will adjust all interior lighting.
Page 158: Head-Up Display (Hud)
Head-Up Display (HUD) CAUTION: If the HUD image is too bright, or too high in your ﬁeld of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your ﬁeld of view.
Page 159 There are three HUD modes that can be viewed in the HUD display. Press the MODE button to scroll through these modes in the following order: Street Mode supports audio and navigation functions with your choice of tachometer settings. Track Mode 1 supports the G-Force gage and minor gages with a circular tachometer.
Page 160 Be sure to continue scanning the displays, controls and driving environment just as you would in a vehicle without HUD. If you never look at the instrument panel cluster, you may miss something important, such as a warning light. Under important warning conditions, the CHECK GAGES warning will illuminate in the HUD.
Page 161 2. Adjust the seat to a comfortable driving position. If your seat position changes, the HUD may need to be re-adjusted. 3. Press the up or down arrows to center the HUD image in your view. The HUD image can only be adjusted up and down, not side-to-side.
Page 162: Accessory Power Outlet(S)
Accessory Power Outlet(s) The accessory power outlet can be used to connect electrical equipment, such as a cellular phone. The accessory power outlet is located inside the center console storage compartment, on the forward left side. To use the outlet, remove the tethered cap. When not using it, always cover the outlet with the protective cap.
Page 163: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter The ashtray and cigarette lighter are located on the instrument panel, in front of the shift lever. To use the ashtray, press on the indentation at the top of the door. Notice: If papers, pins, or other ﬂammable items are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle.
Page 164: Automatic Operation
When the vehicle is ﬁrst started, the display shows the driver’s temperature setting, the outside temperature, the fan speed and the air delivery, for about 10 seconds. The outside temperature is shown in the center of the display. The digital display will show the readings in Fahrenheit or Celsius.
Page 165: Manual Operation
Manual Operation Driver Power/Temperature: Press the driver temperature knob to turn the climate control system off. This is the only setting that completely shuts off the fan. The digital display shows only the outside temperature. The driver and the passenger set temperature and the air intake mode can still be adjusted when the climate control is off.
Page 166 (Defrost): This mode clears the windows of fog or frost more quickly. Air is directed to the windshield, with a small amount directed to the side window outlets. The indicator light comes on and the digital display will show the defrost mode symbol and fan speed when the front defrost mode is being used.
Page 167 (Recirculation): Press to turn the recirculation mode on or off. An indicator light comes on to show that recirculation is on. This mode prevents outside air from entering your vehicle. It can be used to prevent outside air and odors from entering your vehicle and to help cool the air inside your vehicle more quickly.
Page 168: Rear Window Defogger
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. The rear window defogger only works when the engine is running. (Rear Window Defogger): Press to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible.
Page 169: Passenger Compartment Air Filter
Passenger Compartment Air Filter The passenger compartment air ﬁlter removes certain particles from the air including pollen and dust particles. Reductions in airﬂow, which may occur more often in dusty areas, indicate that the ﬁlter may need to be replaced. See Scheduled Maintenance on page 6-4 for information on how often to replace the ﬁlter.
Page 170: Warning Lights, Gages, And Indicators
3. Remove the ﬁlter and install the new air ﬁlter. 4. Replace the ﬁlter cover. 5. Attach the retainer clips. 3-32 Warning Lights, Gages, and Indicators Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 171: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster and Driver Information Center (DIC) are designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel the vehicle has left and many other things needed to know to drive safely and economically.
Page 172 ZR1– United States shown Canada similar 3-34...
Page 173: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the speed in either miles per hour (mph) or kilometers per hour (km/h). For more information see “Personal Options” under DIC Vehicle Personalization on page 3-73. To read the odometer with the ignition off, turn on the parking lamps.
Page 174: Airbag Readiness Light
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-44.
Page 175: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-51 for important safety information. The rearview mirror has a passenger airbag status indicator. United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 176: Voltmeter Gage
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. CAUTION: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 177: One-To-Four Shift Light
One-to-Four Shift Light (Manual Transmission) When this light comes on, the vehicle can only be shifted from 1 (First) to 4 (Fourth) instead of 1 (First) to 2 (Second). The shift must be completed into 4 (Fourth) to turn off this feature.
Page 178: Brake System Warning Light
Brake System Warning Light The vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working well. United States This light comes on brieﬂy while starting the engine.
Page 179: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Page 180: Active Handling System Light
This light turns off when the TCS is turned back on and a TRACTION SYSTEM ON message displays on the DIC See Traction Control System (TCS) on page 4-6 and DIC Warnings and Messages on page 3-56 for more information. This light also comes on while the vehicle is in the Competitive Mode.
Page 181: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the shaded area, the engine is too hot. This means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible.
Page 182: Malfunction Indicator Lamp
When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light ﬂashes for about a minute and stays on steady for the remainder of the ignition cycle.
Page 183 This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. The following can prevent more serious damage to the vehicle: •...
Page 184: Emissions Inspection And Maintenance Programs
If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control...
Page 185: Maintenance Schedule
Engine Oil Pressure Gage United States United States — Z06 and ZR1 Models Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Page 186: Security Light
Security Light For information regarding this light and the vehicle’s security system, see Theft-Deterrent System on page 2-18. Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-17 for more information.
Page 187: Fuel Gage
Fuel Gage The fuel gage shows how much fuel the vehicle has left while the engine is on. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. When the needle approaches the low fuel symbol, a chime sounds and LOW FUEL appears on the Driver Information Center (DIC) display.
Page 188: Boost Gage (Zr1 Only)
The DIC buttons are located on the instrument panel, to the right of the cluster. The DIC comes on when the ignition is turned on. After displaying CORVETTE BY CHEVROLET, the DIC shows the information that was last displayed before the engine was turned off.
Page 189 (Fuel): Press this button to display fuel information such as fuel economy and range. (Gages): Press this button to display gage information like oil pressure and temperature, coolant temperature, automatic transmission ﬂuid temperature, if equipped, battery voltage, and front/rear tire pressures. TRIP: Press this button to display your total and trip distance driven, the elapsed time function, your average speed, and the engine oil life.
Page 190 FUEL Button The fuel button displays average fuel economy and instantaneous fuel economy, calculated for your speciﬁc driving conditions, and range information. Average Fuel Economy: The average fuel economy is viewed as a long-term approximation of your overall driving conditions. You should reset the average fuel economy display every time you refuel.
Page 191 GAGES Button The gages button displays oil pressure, oil temperature, coolant temperature, transmission ﬂuid temperature for automatic transmission vehicles only, battery voltage, and tire pressure information. Oil Pressure: This display shows the oil pressure. Press the gages button to display the oil pressure, such as: •...
Page 192: Trip Button
Battery Voltage: This display shows the current battery voltage. Press the gages button again to display the battery voltage, such as: • BATTERY VOLTAGE 13.5 VOLTS Tire Pressure: This display shows the tire pressure for each tire. Press the gages button again to display the tire pressure for the front tires, such as: •...
Page 193 There is also a miles since last ignition feature that displays the number of miles (kilometers) driven since you last started the vehicle. Press and hold the RESET button for three seconds, then release it. The miles (kilometers) since the last ignition cycle will be set into the trip odometer.
Page 194: Reset Button
OPTION Button The OPTION button allows you to access the PERSONAL OPTIONS menu and customize the personalization settings on your vehicle. See DIC Vehicle Personalization on page 3-73 for more information. RESET Button The RESET button, used along with other buttons, will reset system functions and turn off or acknowledge messages on the DIC.
Page 195: Battery Saver Active
ACTIVE HANDLING This message displays when the Active Handling System is operating. The Active Handling System is a computer controlled system that assists the driver in controlling the vehicle in difficult driving conditions. You may feel or hear the system working and see the ACTIVE HANDLING message displayed in the DIC.
Page 196: Buckle Seatbelt
BUCKLE SEATBELT This message reminds you to buckle the driver’s safety belt. This message displays and a sound will be heard when the ignition is on, the driver’s safety belt is unbuckled, and the vehicle is in motion. You should buckle your safety belt.
Page 197: Competitive Driving Mode
CHECK GAS CAP This message displays if the fuel cap has not been fully tightened. Check the fuel cap to make sure that it is on properly. Once tightened, it takes at least one overnight park to reset or clear this message. If both the CHECK GAS CAP message and the malfunction indicator lamp in the instrument panel cluster are on, you may need to see your dealer/retailer for service.
Page 198 COOLANT OVER TEMPERATURE This message displays and a sound will be heard if the engine coolant exceeds 255°F (124°C). If you have been operating the vehicle under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.
Page 199: Ice Possible
HEADLAMPS SUGGESTED This message displays if it is dark enough outside and the headlamps and the Twilight Sentinel off. This message informs the driver that turning on the exterior lamps is recommended. It has become dark enough outside to require the headlamps and/or other exterior lamps.
Page 200: Low Tire Pressure
LOW OIL PRESSURE This message displays if low oil pressure levels occur. If this message appears while the engine is running, stop the engine and do not operate it until the cause of low oil pressure is corrected. Severe damage to the engine can result.
Page 201 MAXIMUM SPEED 80 MPH (129 km/h) This message displays when a malfunction is present in the Selective Ride Control system. The vehicle speed will be limited to a value determined by the vehicle when the shock absorber system has failed and the shocks are in their full soft mode.
Page 202: Automatic Transmission Only
NO FOB - OFF OR RUN? This message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off. The vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed.
Page 203 Multiple chimes sound when this message is displayed. To acknowledge the message, press the RESET button. The message reappears every ﬁve minutes until this condition changes. If the REDUCED ENGINE POWER message is displayed in combination with the COOLANT OVER TEMPERATURE message, see Engine Overheating on page 5-39.
Page 204: Service Charging System
SERVICE CHARGING SYSTEM If this message displays while you are driving, there may be a problem with the electrical charging system. It could mean that there is a loose or broken drive belt or that there is another electrical problem. Have the vehicle checked right away by your dealer/retailer.
Page 205: Service Transmission
SERVICE TRACTION SYSTEM If this message displays when you are driving, there is a problem with the Traction Control System (TCS) and the vehicle is in need of service. See your dealer/retailer. When this message is displayed, the system will not limit wheel spin.
Page 206 The vehicle will remain in ACCESSORY, without the 20 minute time-out period, until the shift lever is moved to P (Park) or until the driver presses the pushbutton to restart the vehicle. See Ignition Positions on page 2-23 for more information. SHIFT TO PARK OR SET PARK BRAKE FOR TOP If the vehicle has an automatic transmission, this...
Page 207 This message is followed by the MAXIMUM SPEED 55 MPH (90 km/h) message, and then by the REDUCED HANDLING message. The Active Handling System will intervene more quickly when a ﬂat tire has been detected. Adjust your driving accordingly. You can receive more than one tire pressure message at a time.
Page 208 TRACTION SYSTEM AND ACTIVE HANDLING – OFF This message displays, the instrument panel cluster light turns on, and a sound will be heard when the Traction Control System (TCS) and Active Handling System are turned off by pressing the Active Handling System button on the console for ﬁve seconds.
Page 209: Turn Signal On
TRANSMISSION HOT IDLE ENGINE This message displays and four chimes sound if the transmission ﬂuid temperature rises above 270°F (132°C) or rises rapidly. The transmission may shift gears or apply the torque converter clutch to reduce the ﬂuid temperature. Driving aggressively or driving on long hills can cause the transmission ﬂuid temperature to be higher than normal.
Page 210: Other Messages
Other Messages Here are more messages that you can receive on your Driver Information Center (DIC). To acknowledge a message and read another message that may have come on at the same time, press the RESET button. • ACCESSORY MODE ON •...
Page 211: Dic Vehicle Personalization
DIC Vehicle Personalization Many features on your vehicle can be personalized. This means that the operation of these features can be set to operate differently depending on who is driving the vehicle. See “Personal Options” later in this section for the features that you can personalize. The personalization settings for other features are automatically updated and saved as the driver adjusts them.
Page 212 Entering the Personal Options Menu To enter the personal options menu, use the following steps: 1. If you have an automatic transmission vehicle, turn the vehicle on with the shift lever in P (Park). If you have a manual transmission vehicle, turn the vehicle on with the parking brake set.
Page 213 Press the OPTION button until AUTO MEMORY RECALL appears on the display, then press the RESET button to scroll through the following modes: • • NO (default) If you choose YES, the driver’s seat, the outside rearview mirrors and the telescopic steering column, if your vehicle has this feature, positions are recalled when you turn the ignition on.
Page 214 Approach Lights: This option brieﬂy turns on the parking lamps, the high-beam headlamps and the back-up lamps during low light periods when the keyless access transmitter is used to unlock the vehicle. Press the OPTION button until APPROACH LIGHTS appears on the display, then press the RESET button to scroll through the following modes: •...
Page 215 If you choose 90 S, the twilight delay time will be set to 90 seconds. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option. Flash at Unlock: This option activates the front and rear turn signals for two short ﬂashes when the unlock or hatch/trunk button on the keyless access transmitter is pressed.
Page 216 FOB Reminder: This option sounds the horn three times when the driver’s door is closed and there is a keyless access transmitter inside the interior of the vehicle. This will only occur when the vehicle is off. Press the OPTION button until FOB REMINDER appears on the display, then press the RESET button to scroll through the following modes: •...
Page 217 If you choose HORN, the doors will automatically lock and the horn will sound a short time after you remove a keyless access transmitter from the interior of the vehicle and close both doors. If you are parking in a quiet area and do not want the horn to sound when the doors lock, press the lock button on the keyless access transmitter immediately after removing it from the interior and closing the doors.
Page 218 When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option. Language: This option allows you to select the language the DIC, the Head-Up Display (HUD), if your vehicle has this feature, and the radio uses to display messages.
Page 219 4. Press the OPTION button and a cursor will display where you can insert a letter. 5. Press the OPTION button again until the letter you want is displayed. To scroll through the letters faster and without a beeping noise, keep the OPTIONS button depressed.
Page 220: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 221: Radio(S)
Radio(s) Single CD Radio shown, Six-Disc CD Radio similar The vehicle has one of these radios as its audio system. An indicator light on the upper left side of the radio ﬂashes when the ignition is off, to indicate the theft deterrent feature is set.
Page 222: Audio Settings
Audio Settings Press and hold when no tone or speaker control is displayed to adjust all tone and speaker controls to the middle position. AUDIO SETTINGS CENTERED displays. Adjusting the Tone (Bass/Treble) (Bass/Treble): To adjust the Bass or Treble: Press and release until BASS or TREBLE displays.
Page 223 AUTO (Automatic Volume): Automatic volume automatically adjusts the audio system to make up for road and wind noise, by increasing the volume as vehicle speed increases. ® For vehicles without the Bose sound system: 1. Set the volume at the desired level. 2.
Page 224: Using The Radio
Using the Radio Radio Data System (RDS) RDS features are available for use only on FM stations that broadcast RDS information. The station name or call letters display while the radio is tuned to an RDS station. This system relies upon receiving speciﬁc information from these stations and works only when the information is available.
Page 225: Setting Preset Stations
To scan preset stations: Press and hold for four seconds until PRESET SCAN displays. The radio goes to the next preset station, plays for a few seconds, then goes to the next preset station. Press again or one of the pushbuttons to stop scanning presets.
Page 226: Radio Messages
Radio Messages CAL ERR (Calibration Error): Displays if the radio is no longer conﬁgured properly for the vehicle. The vehicle must be returned to your dealer/retailer for service. LOC (Locked): Displays when the THEFTLOCK system has locked up. The vehicle must be returned to your dealer/retailer for service.
Page 227: Using The Cd Player
Radio Messages for XM Only See XM Radio Messages on page 3-96 XM Radio Messages later in this section for further detail. Using the CD Player The CD player can play smaller 3 inch (8 cm) single CDs with an adapter ring. A CD in the player it stays in the player when the ignition is turned off.
Page 228 Playing a CD (Tune): Turn to go to the next or previous track. (Reverse): Press and hold to reverse within the current track. (Fast Forward): Press and hold to fast forward through the current track. SEEK : Press the left arrow to go to the start of the current track if more than eight seconds have played.
Page 229 The CD is automatically pulled back into the player if the CD is not removed after 25 seconds. Pushing a CD back into the player, before the 25 second time period is complete causes the player to sense an error and the CD player tries to eject the CD several times before stopping.
Page 230 SONGLIST FULL displays if more than 20 selections are stored. To play tracks: 1. Press . One beep sounds and S-LIST displays. The recorded tracks begin to play in the order they were saved 2. Press to go back or forward within the saved tracks.
Page 231: Using The Auxiliary Input Jack
Care of the CD Player Do not add labels to a CD, it could get caught in the CD player. Use a marking pen to write on the top of the CD if a description is needed. Do not use CD lens cleaners, they could damage the CD player.
Page 232: Using An Mp3
Using an MP3 MP3 Format Radios with the MP3 feature can only play CD-R discs. Do not mix standard audio and MP3 ﬁles on the same disc. Supported File Structure Radios with the MP3 feature support up to: • 50 folders. •...
Page 233 Playing an MP3 Insert a CD partway into the slot, label side up. The player pulls it in, and READING displays. The CD should begin playing and the CD symbol displays. If the ignition or radio is turned off with a CD-R in the player, it stays in the player.
Page 234: Xm Radio Messages
(Information): Press to display the artist name and album contained in the ID3 tag. BAND: Press to listen to the radio when a CD is playing. The inactive CD remains inside the radio for future listening. CD AUX (Auxiliary): Press to play a CD when listening to the radio.
Page 235: Audio System
Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. ® Bluetooth Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Proﬁle to make and receive phone calls. The system can be used while the key is in ON/RUN or ACC/ACCESSORY position.
Page 236: Pairing A Phone
Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system ﬁrst and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar Calling, if available.
Page 237: Storing Name Tags
Listing All Paired and Connected Phones 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices.
Page 238 Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please”...
Page 239: Deleting Name Tags
4. After the complete number has been entered, say “Store”. The system responds with “Please say the name tag” followed by a tone. 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>.
Page 240: Making A Call
Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). To use the delete all name tags command: 1. Press and hold for two seconds.
Page 241: Receiving A Call
4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear”...
Page 242: Call Waiting
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press to answer an incoming call when another call is active. The original call is placed on hold. • Press again to return to the original call.
Page 243: Bluetooth System
To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press . The system responds with “Ready” followed by a tone. 2. Say “Transfer Call.” The system responds with “Transferring call” and the audio will switch from the vehicle to the cell phone.
Page 244 Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls.
Page 245: Theft-Deterrent Feature
Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indeﬁnitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
Page 246: Audio Steering Wheel Controls
Audio Steering Wheel Controls For vehicles with steering wheel controls, some audio controls can be adjusted at the steering wheel. (Mute/Push to Talk): Press to silence the vehicle speakers only. Press again to turn the sound on. ® For vehicles with OnStar or Bluetooth systems press and hold for longer than two seconds to interact...
Page 247: Radio Reception
To select tracks on a CD: • Press to go to the next or to the previous track when a CD is playing. • Press and hold for more than two seconds to scan the current CD. The CD goes to the next track, plays the ﬁrst 10 seconds, then goes to the next track.
Page 248: Diversity Antenna System
XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
Page 249: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-5 Traction Control System (TCS) ...4-6 Active Handling System ...4-7 Limited-Slip Rear Axle ...4-9 Selective Ride Control ...4-9...
Page 250: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 251: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 252: Braking
Braking See Brake System Warning Light on page 3-40. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second. But that is only an average.
Page 253: Antilock Brake System (Abs)
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little.
Page 254: Traction Control System (Tcs)
Traction Control System (TCS) The vehicle has a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the rear wheels are spinning too much or are beginning to lose traction.
Page 255: Active Handling System
To turn the system off, press the button located on the console. The system can be turned on or off at any time by pressing the ACTIVE HANDLING button. The DIC will display the appropriate message when the button is pushed.
Page 256 The Active Handling System comes on automatically whenever the vehicle is started. To help maintain directional control of the vehicle, the system should always be left on. The system can be turned off needed. If the Active Handling System is turned off, the Traction Control System will also be turned off.
Page 257: Limited-Slip Rear Axle
This light will be on when the vehicle is in the Competitive Driving Mode. When the ACTIVE HANDLING button is pressed again, the Active Handling and Traction Control Systems will be on. The TRACTION SYSTEM AND ACTIVE HANDLING-ON message will be displayed brieﬂy in the DIC and a chime will be heard.
Page 258: Steering
This knob is located on the center console. Turn it to select the suspension of your choice. TOUR: Use for normal city and highway driving. This setting provides a smooth, soft ride. SPORT: Use where road conditions or personal preference demand more control. This setting provides more “feel”, or response to the road conditions.
Page 259: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 260: Off-Road Recovery
Off-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 261 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Page 262: Racing Or Other Competitive Driving
Racing or Other Competitive Driving Racing or competitive driving may affect the vehicle warranty. See the warranty book before using the vehicle for racing or other competitive driving. Notice: If you use the vehicle for racing or other competitive driving, the engine may use more oil than it would with normal use.
Page 263: Zr1 Brake Burnish Procedure
ZR1 Brake Burnish Procedure Notice: These procedures are speciﬁc to the ZR1 with ceramic brake rotors. These procedures should not be run on other Corvette models as damage may result. Notice: The new vehicle break-in period should be completed before performing the brake burnish procedure or damage may occur to the powertrain/engine.
Page 264: Driving At Night
Racing/Track Brake Burnish Procedure To prepare the ZR1 brake system for track events and racing, the Street High Performance Brake Burnish as described previously should be completed. In addition to completing the Street High Performance Brake Burnishing Procedure, the following additional procedure needs to be completed to make the ZR1 brake system ready for track events and racing.
Page 265: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water.
Page 266: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 267: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 268: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 269 CAUTION: Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: •...
Page 270: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 4-22. If the vehicle has a traction system, it can often help to free a stuck vehicle.
Page 271: Loading The Vehicle
Loading the Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certiﬁcation label.
Page 272 For more information on tires and inﬂation see Tires on page 5-62 and Inﬂation - Tire Pressure on page 5-71. There is also important loading information on the vehicle Certiﬁcation label. It tells you the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axle.
Page 273 Example 1 Item Description Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight @ 150 lbs (68 kg) x 1 = Available Occupant and Cargo Weight = Total Item 400 lbs (181 kg) 150 lbs (68 kg) 250 lbs (113 kg) Example 2 Description Vehicle Capacity...
Page 274 Example 3 Item Description Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight @ 200 lbs (91 kg) x 2 = Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating 4-26 positions.
Page 275 Do not load your vehicle with more weight than it was designed to carry. See “Steps for Determining Correct Load Limit” earlier in this section. CAUTION: Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Page 276: Towing
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/ retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-7. 4-28 Recreational Vehicle Towing Notice: Dolly towing or dinghy towing the vehicle...
Page 277: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-7 Fuels in Foreign Countries ...5-8...
Page 278 Section 5 Inﬂation - Tire Pressure ...5-71 High-Speed Operation ...5-72 Tire Pressure Monitor System ...5-73 Tire Pressure Monitor Operation ...5-75 Tire Inspection and Rotation ...5-77 When It Is Time for New Tires ...5-77 Buying New Tires ...5-78 Different Size Tires and Wheels ...5-80 Uniform Tire Quality Grading ...5-80 Wheel Alignment and Tire Balance ...5-82 Wheel Replacement ...5-82...
Page 279: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes,...
Page 280: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 281: Adding Equipment To The Outside Of The Vehicle
If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-16. This vehicle has an airbag system.
Page 282: Gasoline Speciﬁcations
If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. Otherwise, you could damage the engine. If you are using gasoline rated at 87 octane or higher and you hear heavy knocking, the engine needs service.
Page 283: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 284: Fuels In Foreign Countries
We recommend against the use of such gasolines. Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system could be affected. The malfunction indicator lamp might turn on. If this occurs, return to your dealer/retailer for service.
Page 285 The tethered fuel cap is located behind a hinged fuel door on the driver side of the vehicle. The fuel door release button is located on the instrument panel to the left of the steering wheel. Push the button to release the fuel door.
Page 286 There is also a manual fuel door release tab. It is located against the upper trim in the rear compartment on the driver side of the vehicle. Pull the tab to release the fuel door. To remove the fuel cap, turn it slowly counterclockwise. While refueling, let the cap hang by the tether below the fuel ﬁll opening.
Page 287: Filling A Portable Fuel Container
When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere.
Page 288: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. 5-12 CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 289: Hood Release
Hood Release To open the hood: 1. Pull the hood release lever with this symbol on it. It is located inside the vehicle below the instrument panel on the driver side. 2. Go to the side of the vehicle and pull up on the rear edge of the hood, near the windshield.
Page 290: Engine Compartment Overview
Engine Compartment Overview If your vehicle has the 6.2L LS3 V8 engine and you are facing the front, when you open the hood, here is what you will see: 5-14...
Page 291 A. Clutch Master Cylinder Reservoir (If Equipped). See Hydraulic Clutch on page 5-31. B. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-42. C. Brake Fluid Reservoir. See “Brake Fluid” under Brakes on page 5-43. D.
Page 292 If your vehicle has the 6.2L LS9 Supercharged V8 engine and you are facing the front, when you open the hood, here is what you will see: 5-16...
Page 293 A. Intercooler. See Cooling System (Engine) on page 5-32 or Cooling System (Intercooler) on page 5-33. B. Engine Air Cleaner/Filter on page 5-28. C. Power Steering Fluid Reservoir and Cap. See Power Steering Fluid on page 5-41. D. Coolant Surge Tank and Pressure Cap. See Engine Coolant on page 5-34.
Page 294 If your vehicle has the 7.0L LS7 V8 engine and you are facing the driver side of the vehicle, when you open the hood, here is what you will see: 5-18...
Page 295: Engine Oil
A. Engine Air Cleaner/Filter on page 5-28. B. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-41. C. Engine Compartment Fuse Block on page 5-106. D. Remote Positive (+) Terminal (Out of View). See Jump Starting on page 5-50. E.
Page 296: When To Add Engine Oil
When to Add Engine Oil (Except ZO6 and ZR1) If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-110.
Page 297 Checking Engine Oil (ZO6 and ZR1) A. Engine Oil Dipstick B. Engine Oil Fill Cap It is a good idea to check the engine oil level at each fuel ﬁll. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground.
Page 298 If the vehicle has been parked for an extended period without the engine being started, some oil will seep back into the oil pan, reducing the amount of oil held in the dry sump tank and there could be no engine oil at all showing on the dipstick.
Page 299: Changing Engine Oil And Filter
When to Add Engine Oil (ZO6 and ZR1) If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil through the oil ﬁll cap opening in the oil tank. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-110.
Page 300 ZO6 Shown, ZR1 Similar A. Engine Oil Drain Plugs B. Seals 1. Remove the two engine oil drain plugs from the bottom of the engine oil pan. One drain plug drains the external oil tank via the oil transfer supply line.
Page 301: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard. Use only an oil that meets GM Standard GM4718M.
Page 302: Engine Oil Life System
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM4718M are all that is needed for good performance and engine protection. Engine oil system ﬂushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 303: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL message being turned on, reset the system.
Page 304: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-14 for the location of the engine air cleaner/ﬁlter. Notice: If you spray water into the engine air cleaner/ﬁlter intake and water enters the engine air cleaner/ﬁlter housing, you could damage your vehicle’s engine.
Page 305 To inspect or replace the engine air cleaner/ﬁlter: 6.2 L LS3 Engine 6.2 L LS9 Engine shown, 7.0 L LS7 Engine similar 1. Remove the screws holding the air cleaner assembly. 2. Pull the air cleaner assembly back to gain access to the ﬁlter element.
Page 306 3. Remove the screws holding the ﬁlter element in place. 4. Inspect or replace the ﬁlter. See Maintenance Replacement Parts on page 6-14. 5. Reverse Steps 1 and 3 to replace the air cleaner/ﬁlter cover. 5-30 CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned.
Page 307: Automatic Transmission Fluid
Automatic Transmission Fluid How to Check Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to your dealer/retailer service department and have it repaired as soon as possible.
Page 308: Cooling System (Engine)
When to Check and What to Use The hydraulic clutch ﬂuid reservoir cap has this symbol on it. See Engine Compartment Overview on page 5-14 for reservoir location. Refer to the Maintenance Schedule for the proper ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12.
Page 309: Cooling System (Intercooler)
CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
Page 310: Engine Coolant
Checking Coolant 1. Verify that the engine and intercooler are no longer hot. 2. Place a cloth to absorb possible coolant loss under the driver’s side bleeder valve (A). 5-34 3. Loosen, but do not completely unscrew the bleeder valve to check for coolant in the system. 4.
Page 311: What To Use
What to Use CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but would not get the overheat warning.
Page 312: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant...
Page 313 CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the coolant surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the coolant surge tank pressure cap, is hot.
Page 314 3. Fill the coolant surge tank with the proper DEX-COOL coolant mixture until the level inside stabilizes at the FULL COLD mark on the front of the surge tank. 5-38 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 315: Engine Overheating
5. Replace the pressure cap. Be sure the pressure cap is hand-tight and fully seated. Check the level in the surge tank when the system has cooled down. If the coolant is not at the proper level, repeat Steps 1 through 4, then reinstall the pressure cap.
Page 316: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down.
Page 317: Overheated Engine Protection Operating Mode
If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down. Also, see “Overheated Engine Protection Operating Mode”...
Page 318: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid: 1. Turn the ignition off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 319: Brakes
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-14 for reservoir location. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. •...
Page 320: Checking Brake Fluid
Do not top off the brake ﬂuid. Adding ﬂuid does not correct a leak. If ﬂuid is added when the linings are worn, there will be too much ﬂuid when new brake linings are installed. Add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system.
Page 321 CAUTION: With the wrong kind of ﬂuid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake ﬂuid. Notice: • Using the wrong ﬂuid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will...
Page 322 Brake Wear (ZR1 Only) The ZR1 model does not have built-in brake pad wear indicators and periodic visual inspection of the brake pads is required to determine when to replace the brake pads. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.
Page 323 Brake Rotor Wear ZR1 models have ceramic brake rotors. Rotors should be visually inspected whenever the brake pads are replaced. Rotors also need to be weighed before brake pads are replaced to conﬁrm that the rotor mass is greater than the wear-out mass printed on the rotor. The rotor can be reused if the weight of the rotor is above the mass limit.
Page 324: Brake Adjustment
A rotor protector should always be installed before any wheel removal. The protector can be installed by feeding it through the wheel spokes and slipping it over the outer edge of the rotor. Leave the protector in place, over the rotor edge, until the wheel is re-installed.
Page 325: Battery
Battery This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. For battery replacement, see your dealer/retailer or the service manual.
Page 326: Jump Starting
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 327 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3.
Page 328 See Engine Compartment Overview on page 5-14 for the location of the engine compartment fuse block and engine oil ﬁll cap. You will not need to access the battery for jump starting. The remote terminals are for that purpose. CAUTION: An electric fan can start up even when the engine is not running and can injure you.
Page 329 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 330: Rear Axle
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 331: Headlamp Aiming
How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole.
Page 332: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-59. For any bulb changing procedure not listed in this section, contact your dealer/retailer. High Intensity Discharge (HID) Lighting CAUTION: The low beam high intensity discharge lighting system operates at a very high voltage.
Page 333: Headlamps, Front Turn Signal, And Parking Lamps
Headlamps, Front Turn Signal, and Parking Lamps A. High-beam Headlamp B. Low-beam Headlamp C. Front Parking/Turn Signal/Daytime Running Lamp (DRL) If the low-beam headlamp needs to be replaced, see your dealer/retailer. See High Intensity Discharge (HID) Lighting on page 5-56 for more information. To replace a high-beam or front parking/turn signal/ DRL bulb: 1.
Page 334: Taillamps, Turn Signal, And Stoplamps
4. Remove the headlamp bulb by releasing the outer tabs from the socket. 5. Remove the front parking/turn signal bulb by turning the bulb socket counterclockwise. 6. Replace the high-beam headlamp bulb with a new bulb and reattach to the bulb socket. Replace the front parking/turn signal bulb by turning the bulb socket clockwise.
Page 335: Replacement Bulbs
4. Pull the bulb straight out to remove it from the socket. 5. Push the new bulb in the bulb socket until it snaps into place. 6. Reinstall the lamp assembly by ﬁrst lining up the tabs on the bottom of the lamp assembly with the tabs in the vehicle, then slide it in.
Page 336 To remove the wiper blade assembly: 1. Open the hood to gain access to the windshield wipers. 2. Lift the wiper arm away from the windshield. A. Blade Assembly D. Blade Pivot B. Arm Assembly E. Hook Slot C. Locking Tab F.
Page 337 2. Be sure the notches are locked by the bottom claws. Make sure that all other claws are properly locked on both sides of the insert slots. 3. Put the blade assembly pivot in the wiper arm hook. Pull up until the pivot locking tab locks in the hook slot.
Page 338: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Page 339: Winter Tires
Low-Proﬁle Performance Tire The original equipment tires on your vehicle are classiﬁed as low-proﬁle performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle tires and that they tend to wear faster.
Page 340: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger (p-metric) tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 341 (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. Tire Size The following illustration shows an example of a typical passenger (p-metric) vehicle tire size. (A) Passenger (P-Metric) Tire version of a metric tire sizing system.
Page 342: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 343 GAWR RR Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 4-23. Intended Outboard Sidewall asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) The metric unit for air pressure. Light Truck (LT-Metric) Tire light duty trucks and some multipurpose passenger vehicles.
Page 344 Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. A metal support for a tire and upon which the tire beads are seated. Sidewall The portion of a tire between the tread and the bead.
Page 345: Run-Flat Tires
Run-Flat Tires This vehicle, when new, had run-ﬂat tires. There is no spare tire, no tire changing equipment, and no place to store a tire in the vehicle. Run-ﬂat tires perform so well without any air that a Tire Pressure Monitor System (TPMS) is used to alert you if a tire has lost pressure.
Page 346 Some road hazards can damage a tire beyond repair. This damage could occur even before you have driven on the tire in a deﬂated condition. When a tire has been damaged, or if you have driven any distance on a run-ﬂat tire, check with an authorized run-ﬂat tire service center to determine whether the tire can be repaired or should be replaced.
Page 347: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 348: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 349: Tire Pressure Monitor System
If you will be driving your vehicle at speeds of 175 mph (282 km/h) or higher, where it is legal, set the cold inﬂation pressure to the maximum inﬂation pressure shown on the tire sidewall, or 38 psi (265 kPa), whichever is lower.
Page 350 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inﬂation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
Page 351: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly on your vehicle.
Page 352: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 353: Tire Inspection And Rotation
TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you replace one or more of the TPMS sensors or rotate your vehicle’s tires, the identiﬁcation codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver...
Page 354: Buying New Tires
You need a new tire if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.
Page 355 GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Page 356: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover. Additionally, if your vehicle has electronic systems such as, antilock brakes, traction control, and electronic stability control, the performance of these systems can be affected.
Page 357 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 358: Wheel Replacement
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Page 359 CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 360 Tightening Wheel Lug Nuts CAUTION: Never use oil or grease on studs or the threads of the wheel nuts. If you do, the wheel nuts might come loose and the wheel could fall off, causing a crash. CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off.
Page 361: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
Page 362: Lifting The Vehicle
Lifting the Vehicle CAUTION: Lifting a vehicle can cause an injury. The vehicle can slip off the jack and roll over you or other people. You and they could be badly injured. Find a level place to lift your vehicle. To help prevent the vehicle from moving: 1.
Page 363: Lifting From The Front
Lift only in the areas shown in the following pictures. For additional information, see your dealer/retailer and the Chevrolet Corvette service manual. Lifting From the Front The front lifting points can be accessed from either side of your vehicle, behind the front tires.
Page 364 1. Locate the front lifting points (A), according to the illustration shown. 2. Be sure to place a block or pad between the jack and the vehicle. 5-88 3. Lift the vehicle with the jack, making sure the jack spans at least two of the crossmember ribs (B).
Page 365: Lifting From The Rear
Lifting From the Rear The rear lifting points can be accessed from the rear of the vehicle, on either the driver’s or passenger’s side. 1. Locate the rear lifting points (A), according to the illustration shown. 2. Be sure to place a block or pad between the jack and the vehicle.
Page 366: If A Tire Goes Flat
3. Lift the vehicle with the jack, making sure the jack spans at least two of the crossmember ribs (B). For more information, see Doing Your Own Service Work on page 5-4. 5-90 If a Tire Goes Flat It is unusual for a tire to blow out while you are driving, especially if you maintain the tires properly.
Page 367: Appearance Care
The vehicle, when new, had run-ﬂat tires. This type of tire can operate effectively with no air pressure, so you will not need to stop on the side of the road to change a ﬂat tire. You can just keep on driving. The shorter the distance you drive and the slower the speed, the greater the chance that the run-ﬂat tire will not have to be replaced.
Page 368 When cleaning the vehicle’s interior, only use cleaners speciﬁcally designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately.
Page 369: Fabric/Carpet
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on ﬂoor carpet and carpeted ﬂoor mats. For any soil, always try to remove it ﬁrst with plain water or club soda.
Page 370: Coated Moldings
Coated Moldings These moldings are around the hatch opening in the rear area. • When lightly soiled, wipe with a sponge or soft lint-free cloth dampened with water. • When heavily soiled, use warm soapy water. Leather A soft cloth dampened with water can be used to remove dust.
Page 371: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak.
Page 372: Cleaning Exterior Lamps/Lenses
Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the ﬁnish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. Notice: If you drive the vehicle through an automatic car wash that does not have enough clearance for the wide rear tires and wheels, you...
Page 373: Windshield And Wiper Blades
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, chrome polish may be used on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum.
Page 374: Removable Roof Panel
Removable Roof Panel Notice: If you use a glass treatment and/or conditioner that contains ethyl alcohol or ethyl sulfate on the roof panel, you could damage the panel. The repairs would not be covered by your warranty. Only use a GM-approved glass cleaner on the roof panel.
Page 375: Aluminum Or Chrome-Plated Wheels And Trim
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 376: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Page 377: Chemical Paint Spotting
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, we will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within...
Page 378: Service Parts Identiﬁcation Label
Engine Identiﬁcation The eighth character in the VIN is the engine code. This code helps identify the vehicle’s engine, speciﬁcations, and replacement parts. See “Engine Speciﬁcations” under Capacities and Speciﬁcations on page 5-110 for the vehicle’s engine code. Service Parts Identiﬁcation Label This label is on the inside of the glove box.
Page 379: Windshield Wiper Fuses
Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it ﬁxed.
Page 380 Fuses BCK/UP LAMP Reverse Lamps BLANK Not Used BLANK Not Used 5-104 Usage BTSI SOL/STR WHL LCK CLSTR/HUD Fuses Usage Brake Transmission Shift Interlock, Steering Wheel Column Lock Cluster, Heads-Up Display...
Page 381 Fuses Usage CRUISE Cruise Control Switch SWITCH CTSY/LAMP Courtesy Lamp DR LCK Door Locks DRIV DR Driver Door Switch SWITCH Engine Control Module (ECM) Exhaust Module (Z06), EXH MDL Spare (Coupe and Convertible) GM LAN GM LAN Devices RUN/CRNK HTD SEAT/ Heated Seat, Wiper Relays WPR RLY HVAC/...
Page 382: Engine Compartment Fuse Block
Fuses REAR/FOG Rear Fog Lamps TONNEAU Tonneau Release RELSE TRUNK RELSE Trunk Release Fuses AUX PWR Auxiliary Power BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used DRVR HTD Driver Heated Seat SEAT Cigarette Lighter...
Page 383 Fuse Usage Transmission Control Module/Transmission Horn, Alternator Sense Antilock Braking System (ABS)/Real Time Damping Fuse Usage Wiper Stoplamps/Back-Up Lamps Oxygen Sensor Battery Main 5 5-107...
Page 384 Fuse Parking Lamps Powertrain Relay Input/Electronic Throttle Control Manual Transmission Solenoids Antilock Braking System Odd Numbered Fuel Injectors Electronic Suspension Control (Option) Canister Purge Solenoid, Mass Air Flow Sensor Air Conditioner Compressor Even Numbered Fuel Injectors Windshield Washer Headlamp Washer Passenger Side Low-Beam Headlamp Fuel Pump...
Page 385 Micro-Relays Usage Horn Air Conditioning Compressor Windshield Washer Parking Lamps, Foglamps Front Fog Lamp High-Beam Headlamp Headlamp Washer Fuel Pump Mini-Relays Usage Rear Defog Windshield Wiper High/Low Windshield Wiper Run/Accessory Crank Powertrain Ignition 1 Windshield Wiper On/Off Low-Beam Headlamp Spare Fuses Usage Spare Spare...
Page 386: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Cooling System 6.2L LS3 V8 Engine 6.2L LS9 V8 Supercharged Engine – Cooling System 6.2L LS9 V8 Supercharged Engine –...
Page 387 Application Engine Oil with Filter 6.2L LS3 V8 6.2L LS9 V8 Supercharged Engine 7.0L LS7 V8 Engine Fuel Tank Transmission Fluid Automatic Transmission (Pan Removal and Filter Replacement) Manual Transmission – Base Manual Transmission – Z51 Manual Transmission – Z06 Manual Transmission –...
Page 388: Engine Data
Engine VIN Code 6.2L LS3 V8 6.2L LS9 V8 7.0L LS7 V8 Engine Horsepower 6.2L LS3 V8 without 430 @ 5900 rpm option NPP 6.2L LS3 V8 with 436 @ 5900 rpm option NPP 6.2L LS9 V8 638 @ 6500 rpm Supercharged 7.0L LS7 V8 505 @ 6300 rpm...
Page 389 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 390: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 391 This schedule is for vehicles that: • carry passengers and cargo within recommended limits on the Tire and Loading Information label. See Loading the Vehicle on page 4-23. • are driven on reasonable road surfaces within legal driving limits. • use the recommended fuel.
Page 392: Scheduled Maintenance
Scheduled Maintenance When the CHANGE ENGINE OIL message displays, service is required for the vehicle. Have the vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 393 Change engine oil and ﬁlter. See Engine Oil on page 5-19. Reset oil life system. See Engine Oil Life System on page 5-26. An Emission Control Service. Visually check for any leaks or damage. See footnote (g). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-28.
Page 394: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 395: Maintenance Footnotes
Service and Miles (Kilometers) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). ZR1 Only: Intercooler system service (or every ﬁve years, whichever occurs ﬁrst). See footnote (n). Inspect engine accessory drive belt. An Emission Control Service.
Page 396 (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, ﬁttings, and clamps; replace with genuine parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year.
Page 397: Engine Oil Level Check
(m) Drain, ﬂush, and reﬁll clutch hydraulic system at a regular service interval (I or II) every two years. This service can be complex; you should have your dealer/ retailer perform this service. See Hydraulic Clutch on page 5-31. (n) Drain, ﬂush, and reﬁll intercooler system. This service can be complex;...
Page 398: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Page 399: Underbody Flushing Service
Parking Brake and Automatic Transmission P (Park) Mechanism Check CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 400: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard can be identiﬁed as synthetic, and should also be identiﬁed with the American Petroleum Institute (API) Certiﬁed for...
Page 401 Usage Fluid/Lubricant Chassis Chassis Lubricant Lubrication (GM Part No. U.S. 12377985, (Rear Toe-Link in Canada 88901242) or lubricant Outer Ends with meeting requirements of NLGI #2, ZO6, ZR1, or Category LB or GC-LB. Z51 Option) Manual Transmission Fluid Manual (GM Part No. U.S. 88861800, Transmission in Canada 88861801).
Page 402: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter 6.2L LS3 V8 and 7.0L LS7 V8 Engines 6.2L LS9 V8 Supercharged Engine Engine Oil Filter 6.2L LS3 V8 Engines 6.2L LS9 V8 Supercharged Engine 7.0L LS7 V8 Engine Passenger Compartment Air Filter Element...
Page 403: Engine Drive Belt Routing
Engine Drive Belt Routing 6.2L LS9 V8 Engine 6.2L LS3 V8, 7.0L LS7 V8 Engines 6-15...
Page 404: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 405 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 406 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 407: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-5 Customer Assistance for Text Telephone (TTY) Users ...7-6 Customer Assistance Offices ...7-6 GM Mobility Reimbursement Program ...7-7 Roadside Assistance Program ...7-7 Scheduling Service Appointments ...7-10 Courtesy Transportation Program ...7-11 Collision Damage Repair ...7-12 Customer Assistance Information...
Page 408: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 409 STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you can ﬁle with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
Page 410 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Page 411: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Chevrolet dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 412: Customer Assistance For
(2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 413: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000 Long Distance: 011-52-53 29 0 800 GM Mobility Reimbursement...
Page 414: Calling For Assistance
Roadside Assistance program at any time without notiﬁcation. Chevrolet and General Motors of Canada Limited reserve the right to limit services or payment to an owner or driver if they decide the claims are made too often, or the same...
Page 415: Services Provided
• Emergency Tow From a Public Road or Highway: Tow to the nearest Chevrolet dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow.
Page 416: Scheduling Service Appointments
• Trip Interruption Beneﬁts and Assistance: Must be over 250 kilometres from where your trip was started to qualify. General Motors of Canada Limited requires pre-authorization, original detailed receipts, and a copy of the repair orders. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Page 417: Courtesy Transportation Program
Courtesy Transportation Program To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid speciﬁc warranty in both the U.S.
Page 418: Collision Damage Repair
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts.
Page 419: Insuring Your Vehicle
Aftermarket collision parts are also available. These are made by companies other than GM and may not have been tested for your vehicle. As a result, these parts may ﬁt poorly, exhibit premature durability/corrosion problems, and may not perform properly in subsequent collisions. Aftermarket parts are not covered by your GM New Vehicle Limited Warranty, and any vehicle failure related to such parts are not covered by that warranty.
Page 420: If A Crash Occurs
If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. •...
Page 421: Reporting Safety Defects
Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts.
Page 422: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or...
Page 423: Vehicle Data Recording And Privacy
Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model GM vehicles. To request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Page 424: Event Data Recorders
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
Page 425: Onstar
® OnStar If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use. ® See also OnStar System on page 2-41 in this manual for more information.
Page 426 ✍ NOTES 7-20...
Page 427 Accessories and Modiﬁcations ... 5-3 Accessory Power ... 2-24 Accessory Power Outlets ... 3-24 Active Handling System ... 4-7 Active Handling System Light ... 3-42 Additional Required Services, Scheduled Maintenance ... 6-6 Additives, Fuel ... 5-7 Add-On Electrical Equipment ... 5-102 Air Cleaner/Filter, Engine ...
Page 428 Ashtray ... 3-25 Assistance Program, Roadside ... 7-7 Audio System ... 3-82 Audio Steering Wheel Controls ... 3-108 Navigation/Radio System, see Navigation Manual ... 3-97 Setting the Clock ... 3-82 XM™ Satellite Radio Antenna System ... 3-110 Audio System(s) ... 3-83 Audio Systems Radio Reception ...
Page 429 Carbon Monoxide ... 2-14 Engine Exhaust ... 2-36 Winter Driving ... 4-20 Care of Safety Belts ... 5-95 Cargo Cover ... 2-55 CD, MP3 ... 3-94 Center Console Storage ... 2-52 Chains, Tire ... 5-85 Check Engine Lamp ... 3-44 Checking Things Under the Hood ...
Page 430 Cruise Control ... 3-10 Cupholders ... 2-52 Customer Assistance ... 7-6 Offices ... 7-6 Text Telephone (TTY) Users ... 7-6 Customer Information Service Publications Ordering Information ... 7-16 Customer Satisfaction Procedure ... 7-2 Damage Repair, Collision ... 7-12 Data Recorders Event ...
Page 431 EDR ... 7-17 Electrical Equipment Add-On Equipment ... 5-102 Electrical System Engine Compartment Fuse Block ... 5-106 Fuses and Circuit Breakers ... 5-103 Headlamp Wiring ... 5-102 Instrument Panel Fuse Block ... 5-103 Power Windows and Other Power Options ... 5-103 Windshield Wiper Fuses ...
Page 432 Fuel ... 5-5 Additives ... 5-7 California Fuel ... 5-6 Economy Driving ... 4-2 Filling a Portable Fuel Container ... 5-11 Filling the Tank ... 5-8 Fuels in Foreign Countries ... 5-8 Gage ... 3-49 Gasoline Octane ... 5-5 Gasoline Speciﬁcations ... 5-6 Fuses Engine Compartment Fuse Block ...
Page 433 High-Speed Operation, Tires ... 5-72 Highway Hypnosis ... 4-18 Hill and Mountain Roads ... 4-19 Hood Checking Things Under ... 5-12 Release ... 5-13 Horn ... 3-6 How to Wear Safety Belts Properly ... 1-14 Hydraulic Clutch ... 5-31 Ignition Positions ... 2-23 Immobilizer ...
Page 434 Latches, Seatback ... 1-8 Lifting the Vehicle, Tires ... 5-86 Lighting Entry/Exit ... 3-19 Lights Active Handling System ... 3-42 Airbag Readiness ... 3-36 Antilock Brake System (ABS) Warning ... 3-41 Brake System Warning ... 3-40 Exterior Lamps ... 3-14 Flash-to-Pass ...
Page 435 Maintenance Schedule (cont.) Scheduled Maintenance ... 6-4 Using ... 6-2 Your Vehicle and the Environment ... 6-2 Malfunction Indicator Lamp ... 3-44 Manual Seats ... 1-2 Manual Transmission Fluid ... 5-31 Operation ... 2-30 Memory Seat, Mirrors, Steering Wheel Controls ... 1-4 Message DIC Warnings and Messages ...
Page 436 Paint, Damage ... 5-100 Panel, Roof ... 2-57 Park Shifting Into ... 2-33 Shifting Out of ... 2-34 Parking Brake ... 2-32 Over Things That Burn ... 2-35 Parking Your Vehicle ... 2-35 Passenger Airbag Status Indicator ... 3-37 Passenger Compartment Air Filter ... 3-31 Passenger Sensing System ...
Page 437 Reclining Seatbacks ... 1-6 Recommended Fluids and Lubricants ... 6-12 Recreational Vehicle Towing ... 4-28 Reimbursement Program, GM Mobility ... 7-7 Remote, Keyless Access System ... 2-4 Removing the Roof Panel ... 2-57 Replacement Bulbs ... 5-59 Replacement Parts Maintenance ... 6-14 Reporting Safety Defects General Motors ...
Page 438 Service ... 5-3 Accessories and Modiﬁcations ... 5-3 Adding Equipment to the Outside of the Vehicle ... 5-5 Doing Your Own Work ... 5-4 Engine Soon Lamp ... 3-44 Parts Identiﬁcation Label ... 5-102 Publications Ordering Information ... 7-16 Scheduling Appointments ... 7-10 Servicing Your Airbag-Equipped Vehicle ...
Page 439 Tires (cont.) Pressure Light ... 3-43 Pressure Monitor Operation ... 5-75 Pressure Monitor System ... 5-73 Run-Flat ... 5-69 Sidewall Labeling ... 5-64 Terminology and Deﬁnitions ... 5-66 Uniform Tire Quality Grading ... 5-80 Wheel Alignment and Tire Balance ... 5-82 Wheel Replacement ...
Page 440 Warning Lights, Gages, and Indicators ... 3-32 Warnings DIC Warnings and Messages ... 3-56 Hazard Flashers ... 3-6 Safety and Symbols ... iii Wheels Alignment and Tire Balance ... 5-82 Different Size ... 5-80 Replacement ... 5-82 When It Is Time for New Tires ... 5-77 Windows ...

Chevrolet 2009 Corvette Owner's Manual

Section 1 Seats and Restraint System

Front Seats

Child Restraints

Safety Belts

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Roof Panel

Convertible Top

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Rear Axle

Headlamp Aiming

Bulb Replacement

Windshield Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2009 Corvette

Summary of Contents for Chevrolet 2009 Corvette