Table of Contents
Advertisement
Quick Links
Featuring the
WARNING:
If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
-
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
-
Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
This appliance may be installed as an OEM installation in a manufactured (mobile) home and
must be installed in accordance with the manufacturer's instructions and the manufactured
home construction and safety standard, Title 24 CFR, Part 3280 or Standard for Installation in
Mobile Homes, CAN/CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion
kit is supplied with the appliance.
Heritage Owner's Manual
Installer:
After installation give this manual to the home-owner
and explain operation of this heater.
Copyright 2007, T.I.
Burner
$10.00
100-01135
• Direct Vent Freestanding Stove
• Natural Gas or Propane
• Vent Horizontally or Vertically
• Standard Residential
• Mobile Home Approved
Tested and Listed by
Omni-Test Laboratories, Inc.
Beaverton, Oregon
Report # 028 – S – 19 - 1
4800 Harbour Pointe Blvd. SW
4050926
Mukilteo, WA 98275
ANSI Z21.88
Advertisement
Table of Contents
Related Manuals for Lopi Heritage
Summary of Contents for Lopi Heritage
- Page 1 Mobile Homes, CAN/CSA Z240 MH. This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the appliance. Heritage Owner’s Manual Installer: After installation give this manual to the home-owner and explain operation of this heater.
-
Page 2: Introduction
Introduction Introduction We welcome you as a new owner of a Heritage Stove. In purchasing this heater you have joined the growing ranks of concerned individuals whose selection of an energy system reflects both a concern for the environment and aesthetics. The Heritage is one of the finest home heaters the world over. -
Page 3: Table Of Contents
Interior Masonry Chimney Conversions ....35 Vertical Term’s with Two 90° Elbows ....13 Index Termination Requirements ........14 Finalizing the Installation ........15 Index...............36 Opening the Door ..........17 Log Set and Coal Installation ........18 Travis Industries 4 0 2 0 7 2 6 100-01135... -
Page 4: Safety Precautions
• Keep all furniture or other combustible items at least 36” away from the front of the heater. Travis Industries 4 0 4 0 8 0 9 100-01135... - Page 5 Always follow the instructions in this manual. • If the fiber logs become damaged, replace with Travis Industries log set. • Do not touch the hot • Plug the heater into a 120V surfaces of the heater.
-
Page 6: Specifications
The sticker on top of the gas control valve will verify the correct fuel. 20-3/8" Electrical Specifications Electrical Rating............115 Volts, 0.8 Amps, 60 Hz (92 watts on high) Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 7: Installation
This is normal. We recommend you open windows to vent the room. Straight Installations Corner Installations Stove Clearances With this clearance, the vent is centered 15-1/8" from the wall. 10" Min. 4" Min. Mobile Home Requirements Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 8: Heater Placement Requirements
Contact the local gas supplier if the regulator is at an improper pressure. Standard Input Pressure Natural Gas 7” W.C. (1.74 Kpa) P ro p a n e 13” W.C. (3.23 Kpa) Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 9: Vent Requirements
If it does not, apply high temperature sealant to the joints of the affected sections. • Horizontal sections require a 1/4" rise every 12" of travel • Horizontal sections require non-combustible support every three feet (e.g.: plumbing tape) Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 10: Approved Vent Configurations
When a horizontal elbow (90° or 45°) is to the top of the termination Elbow used, horizontal length is the sum of the on vertical terminations. two lengths (H1 + H2). Vent Vertical Elbow Height Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 11: Vertical Term's With (Or Without) 2 45° Elbows
5 feet 5 feet 5 feet 5 feet NOTE: four 4' sections. The maximum offset lengths, combined, is four 4' sections. 0 feet 0 feet 0 feet 0 feet Travis Industries 4 0 4 0 8 0 9 100-01135... - Page 12 12" of travel. Use Restrictor Position # 1 (all shaded areas) 5 feet 5 feet NOTE: A minimum 3 foot rise is required directly off of the stove. 0 feet 0 feet Travis Industries 4 0 4 0 8 0 9 100-01135...
-
Page 13: Vertical Term's With Two 90° Elbows
(Horizontal Length = H1 + H2). horizontal vent length is calculated by adding the length before and after the elbow (H1 + H2 = horizontal vent length). This is considered a vertical elbow Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 14: Termination Requirements
Use the vinyl siding standoff (#950) when installing on an exterior with vinyl siding. • Vent termination must not be located where it will become plugged by snow or other material • These clearances meet UMC-1994 standards. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 15: Finalizing The Installation
If the flames are all blue and Flames should be blue at the on the ends, push the air control in. short, pull the air control out. base, yellow-orange on the top. Travis Industries 4 0 4 0 8 0 9 100-01135... - Page 16 Check the flame on low position. The flames should burn off of each burner hole. If the heater does not work correctly, contact your dealer for a remedy. Give this manual to the home owner and fully explain the operation of this heater. Travis Industries 4 0 4 0 8 0 9 100-01135...
-
Page 17: Opening The Door
When securing the door, make sure the pawl fits over the strike before tightening. NOTE: Do not overtighten the pawl by screwing it in. This will permanently damage the latch. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 18: Log Set And Coal Installation
Top View 1” to 1-1/2” space Do not place Note how the front left log is logs over spaced 1/4” to 3/8” off of the burner holes. burner holes. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 19: Travis Industries
Step 3 Install the embers along the front of the burner (see the illustrations below). Do not place the embers over the burner holes. Front View Side View Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 20: Operation
If using a remote control or thermostat, the On/Off Switch must be left “ON”. Turning the On/Off Switch “OFF” will keep the heater off always. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 21: Starting The Pilot Flame
“f”. Close and latch the door. Turn the gas control knob counter-clockwise to "ON". The pilot is now lit and the heater can be turned on and off. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 22: Starting The Heater For The First Time
Your heater has an adjustable flame to tailor the look and heat output to your specific needs. It is adjusted by turning the middle dial on the gas control valve. Index Mark Flame Height Adjustment Knob Turn counter-clockwise to adjust the flame higher, clockwise to lower. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 23: Adjusting The Blower Speed
This appliance has several areas that reach high temperatures. Dust or other particles on these areas may burn and create a burnt-paper smell. This is normal during startup. You may notice the smell is more acute if the appliance was left idle for a long period. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 24: Maintenance
If the pilot or main burners do not burn correctly, contact your dealer for service. Monitor the blower operation. Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or deterioration is found near the vent termination. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 25: Troubleshooting Steps
Heater for the First Time” Flames Are Too Short The flame height may be turned too low....Turn the flame height to “HI” - See “Adjusting the Flame Height” (Under 6”) Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 26: How This Heater Works
It has been amount of electricity. If the pilot flame tested to be extremely resistant to goes out, the gas valve automatically breakage from temperature changes. shuts off all gas. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 27: Wiring Diagram
Log, Left 98900720 Snap Disk, 120 Degree Log, Rear 93006518 Thermocouple, S.I.T. Log, Right 93006920 Threaded Pipe Adapter - 5/8 x 1/2 Log Set 93006505 Wiring Harness 98900747 On/Off Switch Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 28: Safety Label
Safety Label The listing label is shown below for your records. It can be found inside the right side panel. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 29: Warranty
TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your TRAVIS appliance if it is found to be defective in material or workmanship within the time frame stated within this 7 year warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges (years 1 to 5) prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or dealership. -
Page 30: Optional Equipment & Addenda
Make sure the mixing tubes slide onto the orifices. NOTE: Mixing Tubes Make sure the burner is fully seated. When in place, the pilot flame must align directly above the burner holes. Orifices Travis Industries 4 0 4 0 8 0 9 100-01135... - Page 31 1/2" Wrench Orifice Front Burner Orifice Look here for the orifice identification Front Rear Manifold 5/16” Screw the LP orifice in so the orifice shoulder protrudes 5/16” (indicating full insertion). Travis Industries 4 0 4 0 8 0 9 100-01135...
- Page 32 Screwdriver (or T-20 Torx) NOTE: Make sure the burner is lit. regulator gasket is correctly aligned before installation. Place the LP label on the plate near the gas control valve. Travis Industries 4 0 4 0 8 0 9 100-01135...
-
Page 33: Fireback
Secure installed in step “a”. Secure the with the side fireback clips and fireback with the screw removed in the screws removed in step “b”. step “b”. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 34: Gold Door
Attach the gold grill with the screws removed. To prevent marring of the gold surface, clean the grill with denatured alcohol and a soft cloth. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 35: Installation Addenda
Make sure the coaxial pipe maintains a 1” clearance to any Connector (included in #934 combustible. The vent must be Masonry Conversion Kit) sealed air-tight. secured and sealed to block-off plate. Travis Industries 4 0 4 0 8 0 9 100-01135... -
Page 36: Index
High Wind Vertical Terminations....9 Wiring Diagram..........27 Horizontal Vent Termination Requirements ..14 Yearly Service Procedure......24 How to Measure Vent Lengths ....10 Installation Options ........6 Installation Preparation........7 Leaking Gas .......See Inst. on Cover Travis Industries 4 0 4 0 8 0 9 100-01135...