10 amp on board battery charger
two output (8 pages)
Summary of Contents for Guest Cruising Charger 2632A
Page 1
Cruising Charger Series OWNER’S MANUAL ON BOARD BATTERY CHARGERS Models DC Amperage No. Of Banks Volts 2632A 5,5,20 Amps 3 Bank 12/12 2632A-OEM 2632A-230 2632A-230-OEM 2633A 10,20 Amps 2 Banks 12/12/12 2633A-OEM 2633A-230 2633A-230-OEM * : See Section 3 diagrams for specific connection instructions IMPORTANT NOTICE This manual contains important safety and operating instructions for the charger.
AC current than other charger types. Unlike automotive “trickle” chargers, the 2632A, and 2633A will not boil off the electrolytes in properly installed and maintained batteries. The red and green LED’s, mounted on the charger face let you know the unit is recharging and maintaining your batteries.
Page 3
Personal Safety Precautions (cont’d) Wear complete eye protection and clothing protection. Avoid touching eyes while working near a battery. If battery acid contacts skin or clothing, wash them immediately with soap and water. If acid enters the eye, flood the eye with cold, running water for at least ten minutes and get medical attention.
2. INSTALLING THE CHARGER AC Connection and Grounding Precautions: DANGER DO NOT OPERATE THIS CHARGER WITH A TWO BLADED ADAPTER PLUG OR EXTENSION CORD. DOING SO CAN RESULT IN SERIOUS PERSONAL INJURY. DO NOT ATTEMPT TO WIRE THE BATTERY CHARGER USING AN ELECTRICALLY ENERGIZED LINE CORD.
Page 5
3. For 230 Vac chargers, the AC and DC wiring method is identical to 115 Vac chargers. Note: US Color Code is Black = Line, White = Neutral, Green or Non Insulated = Earth Ground. Euro color coding is Brown = Line; Blue = Neutral; Green, Green/Yellow or Non Insulated = Earth Ground.
Page 6
DC positive output per ABYC standards. If the Guest Cruising Series charger does not come equipped with circuit breakers, an inline fuse must be installed in series with each DC positive output cable to the battery.
Page 7
5/5/20 7.5 Amp 50/60Hz 115VAC 2632A-OEM 12/12/12 5/5/20 7.5 Amp 50/60Hz 230VAC 2632A-230 12/12/12 5/5/20 3.75 Amp 50/60Hz 230VAC 2632A-230-OEM 12/12/12 5/5/20 3.75 Amp 50/60Hz Diagram 1. Standard Connections for a 2632A (5/5/20 Amps) used with 3 independent 12V Batteries...
Page 8
Diagram 2. Standard Connections for a 2632A (5/5/20 Amps) used with 2 12V batteries wired in series for a 24 V system, and one other 12 V battery 2632A Connection Warnings: Do NOT connect the outputs of the 2632A in series or in parallel while charger is AC powered ON.
Page 10
only. While charger is AC powered on, battery switch must be set to “OFF”, “1”, or “2”, not “both”. 4. OPERATING THE CHARGER – 10 (or 5/5) amp output The LED Function Chart describes the charging process for any 10 (or 5/5) Amp output. Display Operating condition When the red LED is on, it indicates that your batteries are discharged and is...
Page 11
OPERATING THE CHARGER – 20 amp output The LED Function Chart describes the charging process for any individual 20 Amp output. Display Operating condition When the red LED is on, it indicates that your batteries are discharged and is recharging them at the "Charging" rate (stage 1). This charging rate is 20 Amps.
AC breaker on the main panel when the AC 2. Charger failure 2. Return charger to the Guest power is applied. Service Dept. 6. MAINTAINING THE CHARGER Periodically clean both battery terminals with baking soda and tighten all connections.
Page 14
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. LIMITED WARRANTY For two (2) years from the date of purchase, The Guest Co. will, at its discretion, repair or replace for the original consumer, free of charge, any parts found defective in material or workmanship.