Table of Contents
Advertisement
Quick Links
LIMITED WARRANTY
For one (1) year from the date of purchase, The Guest Co., Inc.
will, at its discretion, repair or replace for the original consumer,
free of charge, any part or parts found upon examination by Guest
Co., Inc., 48 Elm St., Meriden, Connecticut to be defective in
material or workmanship or both. Proof of purchase required. All
transportation charges under this warranty must be borne by the
consumer.
THERE IS NO OTHER EXPRESSED WARRANTY. IMPLIED
WARRANTIES,
INCLUDING THOSE OF
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR FROM THE DATE OF
PURCHASE. THIS IS THE EXCLUSIVE REMEDY
CONSEQUENTIAL DAMAGES ARE EXCLUDED WHERE
PERMITTED BY LAW.
CUSTOMER SERVICE
If you,
customer, have any questions concerning Guest
our
products, parts or warranties, please contact our Service
Department Monday through Friday between 9:00 AM and 4:00
PM Eastern Time.
(203)-238-0550
(203)-634-1696 fax
The Guest Co.
48 Elm St. Meriden, CT 06450 USA
A Valley Forge Company
Writefor your free copy ofthe new GUEST catalog.
1-24020
I
MERCHANT-
AND
I
4.
ShipWrite
Services
MODEL 2815M
(formerly 2615AM)
I5AMP,2-BANK
BATTERY CHARGER
Installation AND OPERATION
INSTRUCTIONS FOR
MODELS 281 5M11 15 AND 281 5M123D
IMPORTANT!
READ THESE INSTRUCTIONS BEFORE
INSTALLING AND USING THIS PRODUCT.
Keep these instructions for future reference
Advertisement
Table of Contents
Related Manuals for Guest 2815M
Summary of Contents for Guest 2815M
- Page 1 LIMITED WARRANTY For one (1) year from the date of purchase, The Guest Co., Inc. will, at its discretion, repair or replace for the original consumer, free of charge, any part or parts found upon examination by Guest Co., Inc., 48 Elm St., Meriden, Connecticut to be defective in material or workmanship or both.
- Page 2 Description Specifications The Guest 2815M ChargePro is a solid-state “3-stage” battery Total output current charger and is lightweight, silent and completely automatic. It can maximum: 15 amps at 12 volts DC produce a full 15 amps of 12 volt DC charging current while using much less AC current than other chargers.
- Page 3 Checklist for required tools and mate rials Operation Tools When the 2815M charger senses a drop in battery voltage, it Electric drill with 1/4” 1/16” drill bits automatically increases its output to re-charge the battery. By Wire cutting and crimping tools using a sophisticated 3 stage charging method, it recharges your 1/4”...
- Page 4 Planning the DC connections onto a carpeted, upholstered, or varnished surface. You can configure the Guest 281 SM charger to main:ain one 2. Although this charger is ruggedly designed, avoid or two separate 12 volt batteries. There are several ways to mounting it in an areathat is open to rain, snow or spray.
- Page 5 E-9. 1 5h. For sample diagrams of these types of installations, refer to Guest document 1-21681. This is included with all Guest battery switches and isolators, and is available on request.
- Page 6 The DC connections (continued) Remove the two screws on the lower face of the expose the wiring terminals. The AC and DC 3. You will also need to establish a path between the terminals are arranged as shown here: charger’s common DC negative output and the common negative engine ground connection.
- Page 7 The Guest Company strongly recommends 1. Use only a heavy duty 3 conductor AC cord such a:; a Guest part # U-2554 or Radio Shack TM part # 278-1258. that you consult with a qualified marine electrician before installing this device.
- Page 8 OK. If not, Testing your installation (such as lights, pumps, etc.) contact The Guest Co. Activate the battery charger by re-connecting your dockside AC Confirm that AC power is Connect power available, supply cr reset breaker, power.