Advertisement
Models
2613A
2620A
2623A
2631A
* : See Connection diagrams for warnings.
IMPORTANT NOTICE
This manual contains important safety and operating instructions for the charger. Read
the entire manual before using. Also read all instructions and cautions for and on the
charger, batteries and equipment in the vicinity of the batteries.
1. INTRODUCING THE CHARGER
The Guest model 2613A, 2620A, 2623A and 2631A are designed to both recharge
your batteries, and extend your battery's life in applications where it is stored for long
periods of time. They are "3-stage" electronic, completely automatic, lightweight, silent,
battery chargers and each output produces 12 Volts DC at either a full 5 Amps or 10
Amps (model specific), while using much less AC current than other charger types.
Unlike automotive "trickle" chargers, the 2613A, 2620A, 2623A and 2631A will not boil
off the electrolytes in properly installed and maintained batteries. When the charger is
attached to your batteries and plugged into a standard 115 Volt / 60 Hz AC outlet, the
red and green LED's, mounted on the face of the charger let you know the unit is
recharging and maintaining your batteries. This sophisticated device is ideal for
recharging and maintaining the 12VDC batteries in your boat, electric vehicle or cart,
ATV, snowmobile or motorcycle.
Trolling Charger Series
OWNER'S MANUAL
ON BOARD BATTERY CHARGERS
Amperage
5,5,5 Amps
10,10 Amps
10,5,10 Amps
10,10,10 Amps
SAVE THESE INSTRUCTIONS
No. Of Banks
3 Bank
2 Banks
3 Banks
3 Banks
R
Volts
12/24/36
12/24
*12 or 24
12/24/36
Advertisement
Table of Contents
Related Manuals for Guest Trolling Charger 2613A
Summary of Contents for Guest Trolling Charger 2613A
-
Page 1: Introducing The Charger
1. INTRODUCING THE CHARGER The Guest model 2613A, 2620A, 2623A and 2631A are designed to both recharge your batteries, and extend your battery’s life in applications where it is stored for long periods of time. - Page 2 WARNINGS THIS CHARGER SHOULD BE USED TO CHARGE ONLY LEAD ACID OR GEL CELL TYPE BATTERIES. USE ON OTHER BATTERY TYPES MAY EXPLODE AND CAUSE PERSONAL INJURY. RISK OF EXPLOSIVE GASES! WORKING IN THE VICINITY OF LEAD ACID BATTERIES IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.
-
Page 3: Installing The Charger
Add distilled water in each cell until battery acid reaches levels specified by the battery manufacturer, if applicable. Do not overfill. For a battery without cell caps, carefully follow the manufacturer’s recharging instructions. Never allow the ring terminals to touch each other. NEVER charge a frozen battery. - Page 4 Diagram 1. 2613A (5/5/5 Amps) used with 3 independent 12V Batteries 2613A Connection Warnings: For the 2613A, only output 2 and output 3 may be connected in parallel for a 12 V 10 amp output. The engine start output (Output...
- Page 5 2613A Connections Diagram 2. 2613A used in a 24V system To use a 2613A in a 36V system connect all 3 outputs in series.
- Page 6 2620A Connections Output Output DC Cable Size (inches) Input Model Banks Input Volts Volts Amps Size L x W x H Amps Max 115VAC 2620A 12/24 10/10 6’/6’ 9.6 x 7 x 2.6 5 Amps 50/60Hz Diagram 3. 2620A (10/10 Amps) used with 2 independent 12V Batteries...
- Page 7 NOTE: The 2620A can be used on 2 12 volt batteries or a 24V system. Outputs may also be paralleled for a single 12V 20 amp output. 2623A Connections Output Output DC Cable Size (inches) Input Model Banks Input Volts Volts Amps Size...
-
Page 8: 2623A Used In A 24 V System
2) may NOT be connected in parallel with output 1 & 3. Output 1 and 3 may be connected in series for a 24 V system, the engine start output (Output 2) may NOT be connected in series with output 1 and 3. 2623A Connections *Diagram 5: 2623A used in a 24 V system... -
Page 9: Used With 3 Independent 12V Batteries
2631A Connections Output Output DC Cable Size (inches) Input Model Banks Input Volts Volts Amps Size L x W x H Amps Max 115VAC 2631A 12/24/36 10/10/10 6’/6’/6’ 13 x 7 x 2.6 7.5 Amps 50/60Hz Diagram 6: 2631A (10/10/10 Amps) used with 3 independent 12V Batteries NOTE: The 2631A can be used on 3 12 volt batteries, a 24V system, or a 36 volt system. - Page 10 3. OPERATING THE CHARGER – 10 amp output The LED Function Chart describes the charging process for any individual 10 Amp output. Display Operating condition When the red LED is on, it indicates that your batteries are discharged and is recharging them at the "Charging"...
- Page 11 OPERATING THE CHARGER – 5 amp output The LED Function Chart describes the charging process for any individual 5 Amp output. Display Operating condition When the red LED is on, it indicates that your batteries are discharged and is recharging them at the "Charging" rate (stage 1). This charging rate is 5 Amps.
-
Page 12: Troubleshooting
AC breaker on the main panel when the AC 2. Component failure 2. Return charger to the Guest power is applied. Service Dept. 5. MAINTAINING THE CHARGER Periodically clean both battery terminals with baking soda and tighten all connections. -
Page 13: Specifications
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. LIMITED WARRANTY For two (2) years from the date of purchase, The Guest Co. will, at its discretion, repair or replace for the original consumer, free of charge, any parts found defective in material or workmanship.