Advertisement
Y Y Y Y Y our Curtis
our Curtis
our Curtis ADS System is F
our Curtis
ADS System is Factor
ADS System is F
ADS System is F
our Curtis
ADS System is F
After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller.
WILBUR CURTIS
The control displays
Water will fill the tank (approximately 2-3 minutes depending on water flow rate). When the proper level is reached
screen.
WILBUR CURTIS
Control will display
READY TO BREW
T T T T T o Go Into Programming
o Go Into Programming
o Go Into Programming
o Go Into Programming
o Go Into Programming
ON/OFF
ON/OFF
Press ON/OFF
ON/OFF
ON/OFF button (yellow). Press and hold BREW
Continue holding BREW
BREW button. Display will read
BREW
BREW
BREW
1
2
During actual brew cycle
a 2-minute drip mode is
added to the brew time.
The programmed water
level compensates for back to
back brewing in Delta 3 to allow for
an increase of water volume.
>
Pressing
button will display the subsequent menu features.
Next item in the sequence is Brew by Time.
Brew by Time.
Brew by Time.
Brew by Time. Press
Brew by Time.
back and forth from minutes to seconds to exit (ex). Change the time or set and exit by pressing
T T T T T empera
emperature (F
empera
empera
empera
ture (F
ture (Factor
ture (F
ture (F
actor
actory set 200
actor
actor
y set 200
y set 200
y set 200
y set 200°F) F) F) F) F)
<
>
Press
to Select. Press
or
to move to desired temperature and then
Energy Save Mode (Factory set Off)
Energy Save Mode (Factory set Off)
Energy Save Mode (Factory set Off)
Energy Save Mode (Factory set Off)
Energy Save Mode (Factory set Off)
<
>
Press
to Select,
to
ON or OFF,
energy by not heating the tank during period of non-operation (tank temperature maintains at 140º F).
Brew Count Odom
Brew Count Odom
Brew Count Odom
Brew Count Odom
Brew Count Odom
Press
to display total brew cycles. Press ex ex ex ex ex or Reset
Freshness Timer (Factory set Disable)
Freshness Timer (Factory set Disable)
Freshness Timer (Factory set Disable)
Freshness Timer (Factory set Disable)
Freshness Timer (Factory set Disable)
<
Press
to Select,
to Off, or select
Brew Count
Brew Count T T T T T otal
Brew Count
otal
otal
otal
Brew Count
Brew Count
otal
Press
to Select, Shows total gallons and total brew cycles on the unit. Press
Cold Brew Lock . . . (Factory set Delta 3)
Cold Brew Lock . . . (Factory set Delta 3)
Cold Brew Lock . . . (Factory set Delta 3)
Cold Brew Lock . . . (Factory set Delta 3)
Cold Brew Lock . . . (Factory set Delta 3)
<
>
Press
to select,
or
to select desired setting (CBL 5, 15 or OFF),
The CBL feature allows the brewer to brew at three different temperature levels from the actual set point. The first setting is within 5 degrees of set point, next is within
15 degrees of set point, OFF is within 30 degrees of set point for the Ready to Brew message, however it will brew at any temperature. This feature will operate after
initialization to set temperature after the rear standby toggle switch is reset to ON.
Master Reset
Master Reset
Master Reset
Master Reset
Master Reset
Press
to display Are
Are Y Y Y Y Y ou Sure?
Are
Are
Are
ou Sure?
ou Sure?
ou Sure?
ou Sure?
<
>
Then
for Y Y Y Y Y es es es es es,
for No
No No
No No
Brewer factory defaults are then reset.
Service Call (Phone number)
Service Call (Phone number)
Service Call (Phone number)
Service Call (Phone number)
Service Call (Phone number)
Press
to display number and change number or < to move place and EX to exit when complete This number will be displayed during a Heating
SENSOR ERROR or during a WATER ERROR.
Access Code (Factory set 1-2-3-4)
Access Code (Factory set 1-2-3-4)
Access Code (Factory set 1-2-3-4)
Access Code (Factory set 1-2-3-4)
Access Code (Factory set 1-2-3-4)
Press
to display number and change number, (the number can be change 1 to 4) or < to move place and ex ex ex ex ex to exit when complete.
2
actory Pre-Set for Optimum P
actor
actor
y Pre-Set for Optimum P
y Pre-Set for Optimum P
y Pre-Set for Optimum Performance.
actor
y Pre-Set for Optimum P
. Press ON/OFF button and the screen will display
when temperature reaches the setpoint (200°F). Unit is now ready to brew.
BREW
BREW
BREW
BREW button (green) and then press and release ON/OFF
ENTERING PROGRAM
MODE
3
4
PROGRAM MENUS
Brew Volume (Factory Set at 60 oz)
Brew Volume (Factory Set at 60 oz)
Brew Volume (Factory Set at 60 oz)
Brew Volume (Factory Set at 60 oz)
Brew Volume (Factory Set at 60 oz)
This is preset from the factory for use with the Curtis glass bowl. If programming is necessary, the following procedure must be
followed to ensure proper pot levels under all operating conditions.
Selecting Brew by Volume
Brew by Volume or Brew by Time
Brew by Volume
Brew by Volume
Brew by Time
Brew by Time
Brew by Time depends on whether you know your brew time before starting.
Brew by Volume
Brew by Time
>
From Program Menus press
display will now show the next feature.
Brew by V V V V V olume
Brew by
Brew by
Brew by
Brew by
olume
olume: Press
olume
olume
to Select, Display will now show Push START To Begin... Press the BREW
starts running, when desired volume is reached press BREW
to Select to change the brew time. Display will now show the current time. By pressing
to set. When enabled unit will automatically shut off 4 hours from last brew. This feature will save a considerable amount of
>
to set from 20 minutes to 120 minutes in 10 minute increments,
erformance.
erformance.
erformance.
erformance.
<ALP3/4/5>
WILBUR CURTIS
ENTER CODE
, wait until
is displayed Enter the 4-digit access code, the digits 1-4
– – – –
correspond to the buttons (see illustration below).
The default code set at the factory is 1-2-3-4. Then
displayed.
All programming selections are performed with the three center buttons.
The symbols below the buttons are:
Scroll LEFT
SELECTION or ENTER to save new parameter
Scroll RIGHT
Exit
Exit
Exit
Exit
Exit
Press
BREW
BREW
BREW
BREW button again to stop the flow.
.
to set. Temperature is programmable from 170°F to 204°F in 2-degree increments.
for 5 seconds. Not resettable.
to set.
WILBUR CURTIS
. After three seconds,
FILLING
WILBUR CURTIS
HEATING
ON/OFF
ON/OFF
ON/OFF button (yellow).
ON/OFF
PROGRAM MENUS
<
to select, exits program mode and returns unit to operation.
BREW
BREW
BREW button then hot water
BREW
to set.
ALPHA GT
is displayed.
will appear on the
will be
SELECT
>
<
>
or
you can toggle
system
Advertisement
