Program Menus - Curtis D500GT Installation Instructions And Service Manual

Digital airpot brewing systems airpot brewing systems

Hide thumbs

page of 5

/ 5
Bookmarks

Y Y Y Y Y our Curtis

our Curtis

our Curtis ADS System is F

our Curtis

ADS System is F

ADS System is Factor

ADS System is F

our Curtis

ADS System is F

After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller.

WILBUR CURTIS

The control displays

Water will fill the tank (approximately 2-3 minutes depending on water flow rate). When the proper level is reached

screen.

WILBUR CURTIS

Control will display

READY TO BREW

T T T T T o Go Into Programming

o Go Into Programming

ON/OFF

Press ON/OFF

ON/OFF button (yellow). Press and hold BREW

ON/OFF

Continue holding BREW

BREW button. Display will read

BREW

correspond to the buttons (see illustration below).

PROGRAM MENUS

During actual brew cycle

a 2-minute drip mode is

added to the brew time.

The programmed water

level compensates for back to

back brewing in Delta 3 to allow for

an increase of water volume.

T T T T T empera

empera

emperature (F

empera

ture (F

ture (Factor

actor

actory set 200

actor

y set 200°F) F) F) F) F)

y set 200

empera

ture (F

actor

y set 200

< < < < <

> > > > >

Press

to Select. Press

Energy Save Mode (Factory seting OFF)

< < < < <

> > > > >

Press

to Select,

ON or OFF,

feature is OFF, unit does not have the energy saving mode. This feature will save a considerable amount of energy by not heating the tank during periods of non-operation

(tank temperature maintains at 140º F).

Brew Count Odom.

to display total brew cycles. Press ex ex ex ex ex or Reset

Press

Freshness Timer (Factory set Disable)

< < < < <

Press

to Select,

to Off, or select

Brew Count

Brew Count T T T T T otal

otal

Brew Count

otal

Press

to Select, Shows total gallons and total brew cycles on the unit. Not resettable.

Cold Brew Lock . . . (Factory set Delta 3)

< < < < <

> > > > >

Press

to select,

to select desired setting (CBL 5, 15 or OFF),

The CBL feature allows the brewer to brew at three different temperature levels from the actual set point. The first setting is within 5 degrees of set point, next is within

15 degrees of set point, OFF is within 30 degrees of set point for the Ready to Brew message, however it will brew at any temperature. This feature will operate after

initialization to set temperature after the rear standby toggle switch is reset to ON.

Master Reset

Press

to display Are

Are

Are Y Y Y Y Y ou Sure?

ou Sure?

< < < < <

> > > > >

Then

for Y Y Y Y Y es es es es es,

for No

No No.

No No

Brewer factory defaults are then reset.

Service Call (Phone number)

Press

to display number and change number or

ERROR or during a WATER ERROR.

actor

actory Pre-Set for Optimum P

y Pre-Set for Optimum P

y Pre-Set for Optimum Performance.

actor

y Pre-Set for Optimum P

. Press ON/OFF button and the screen will display

when temperature reaches the setpoint (200°F). Unit is now ready to brew.

BREW

BREW button (green) and then press and release ON/OFF

ENTERING PROGRAM

MODE

Brew Volume (Factory Set at 60 oz)

Selecting Brew by Volume

Brew by Volume

Brew by Volume or Brew by Time

Brew by Volume

> > > > >

From Program Menus press

Brew by V V V V V olume

Brew by

olume: Press

olume

to Select, Display will now show Push START To Begin... Press the BREW

Brew by

olume

starts running, when desired volume is reached press BREW

> > > > >

Pressing

button will display the subsequent menu features.

Next item in the sequence is Brew by Time.

< < < < <

> > > > >

time. By pressing

you can toggle back and forth from minutes to seconds to exit (ex). Change the time or set and exit by

pressing

to move to desired temperature and then

to set. When on, temperature is at 140ºF. Also, when enabled unit will automatically shut off 4 hours from last brew. When

> > > > >

to set from 20 minutes to 120 minutes in 10 minute increments,

< < < < <

to move place and EX to exit when complete This number will be displayed during a Heating

erformance.

WILBUR CURTIS

ENTER CODE

, wait until

is displayed Enter the 4-digit access code, the digits 1-4

– – – –

The default code set at the factory is 1-2-3-4. Then

displayed.

All programming selections are performed with the three center buttons.

The symbols below the buttons are:

Scroll LEFT

SELECTION or ENTER to save new parameter

Scroll RIGHT

Exit

Press

Brew by Time

Brew by Time depends on whether you know your brew time before starting.

display will now show the next feature.

BREW

BREW button again to stop the flow. Now the volume has been set.

BREW

Brew by Time.

Brew by Time. Press

Brew by Time.

to Select to change the brew time. Display will now show the current

to set. Temperature is programmable from 170ºF to 204ºF in 2-degree increments.

to set.

WILBUR CURTIS

. After three seconds,

FILLING

WILBUR CURTIS

HEATING

ON/OFF

ON/OFF button (yellow).

PROGRAM MENUS

to select, exits program mode and returns unit to operation.

BREW

BREW button then hot water

BREW

to set.

D500 GT

is displayed.

will appear on the

will be

SELECT

system SENSOR

Table of Contents

This manual is also suitable for:

D500gt/h

Program Menus - Curtis D500GT Installation Instructions And Service Manual

PROGRAM MENUS

Related Manuals for Curtis D500GT

Related Content for Curtis D500GT

This manual is also suitable for: