Related Manuals for Curtis Gemini 12D Series
Summary of Contents for Curtis Gemini 12D Series
- Page 1 USER GUIDE Gemini 12D Series ® Twin Coffee Brewing System READ AND SAVE THESE INSTRUCTIONS NOTICE TO INSTALLER: Please leave this booklet with the machine.
-
Page 2: Table Of Contents
..................IP36 ..................................ES43 ........................ES44 ........................ES45 ..........................................................Contact Information Wilbur Curtis Co., Inc. 6913 Acco Street | Montebello, CA 90640 US Phone: 323-837-2300 | Toll Free: 800-421-6150 Email: csrassistance@wilburcurtis.com | Web: www.wilburcurtis.com . - 4:00 . PT Email: techsupport@wilburcurtis.com... -
Page 3: Fs22
KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS22 Key Features • Brews automatically in 12 or 24 cup increments per cycle. • Automatic timer allows brewing of 24 cups without brew basket reloading. • Hot water faucet lets you draw steaming hot water for tea or soups — even during brewing. •... -
Page 4: Is2
INSTRUCTIONS could result in personal injury or void the warranty. • This appliance is designed for commercial use. Any service other than cleaning and preventive maintenance should be performed by an authorized Wilbur Curtis service technician. • serviceable parts inside. - Page 5 IMPORTANT SAFEGUARDS CE Requirements • This appliance must be installed in locations where it can be overseen by trained personnel. • • • • This appliance must not be cleaned by water jet. • instruction concerning use of the appliance in a safe way and if they understand the hazards involved. •...
-
Page 6: Ii2
INSTALLATION INSTRUCTIONS WARNING: WARNING: properly grounded. NOTICE: SPECIFICATIONS section. IMPORTANT: Installation Instructions Installation Requirements • A secure surface capable of supporting the weight of the appliance. • For units without an attached cord set: Appropriately sized, UL listed, grounding type power cable to meet enough •... -
Page 7: Ii15
INSTALLATION INSTRUCTIONS II15 Installation Leveling WARNING: Use the leveling legs to level the brewer only. Do not use them to adjust brewer height. Do not extend them higher than necessary. Position the brewer on the counter top. Level it left to right and front to back by turning the bottom of the legs. - Page 8 INSTALLATION INSTRUCTIONS II15 Connect the Brewer Wiring (cont.) Power Up the Brewer 10 Turn on the water supply valve. 11 Make sure that the circuit breaker supplying power to the unit is on. 12 Turn the toggle switch on the back of the brewer to the 13 If the control panel is not already lit, push the ON/ to the correct volume, the heating elements will turn on automatically.
-
Page 9: Oi19
OPERATING INSTRUCTIONS OI19 Brewing Instructions WARNING - TO AVOID SCALDING, AVOID SPLASHING. Keep body parts clear of the brewer during ® NOTICE - Do not use IntelliFresh satellites on non-IntelliFresh brewers. The Gemini Brewer is factory preset for optimal performance. The brewer should be ON. - Page 10 OPERATING INSTRUCTIONS OI19 Sleep Mode This function conserves energy. See the PROGRAMMING GUIDE section to turn sleep mode on or off. When enabled, the SLEEP light ( comes on and the brewer reduces the temperature of the water in the tank to 140ºF, when the unit has not brewed for more than two hours.
-
Page 11: Ci1
CLEANING INSTRUCTIONS WARNING: HOT SURFACES - To avoid injury, allow the brewer and dispenser(s) to cool before cleaning. NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives. USE OF THESE PRODUCTS WILL VOID THE WARRANTY. Cleaning The Brewer - Daily WARNING: DO NOT immerse the brewer in water or any other liquid. -
Page 12: Ci3
CLEANING INSTRUCTIONS Cleaning the Satellite (Daily) WARNING: DO NOT immerse the satellite in water or any other liquid. Do not place the satellite in a dishwasher. Placing the satellite in a dishwasher will void the warranty. Cleaning the Liner Prepare a mild solution of detergent and warm water. Remove the satellite from the brewer and remove the lid. - Page 13 CLEANING INSTRUCTIONS Cleaning the Faucet Parts and Site Gauge (cont.) 10 Air Dry - Allow all parts to thoroughly air dry. 11 Reassemble - When dry, reassemble the handle/ bonnet. Hand tighten the handle/bonnet onto the top of the faucet assembly. Reinstall the site gauge (if applicable).
- Page 14 PROGRAMMING GUIDE IMPORTANT: Change the program settings only if necessary. Before programming, allow the brewer to reach brewing temperature. Make sure air is purged from the lines according to the INSTALLATION INSTRUCTIONS. Programming Options Changing the Brew Temperature (Factory Default: 200°F) This function sets the tank water temperature.
- Page 15 PROGRAMMING GUIDE Enabling/Disabling Sleep Mode The unit must be on (the control panel must be lit) to enable/disable sleep mode. Press the ON/OFF button until the SLEEP light ( comes on, then release. To disable: Press the ON/OFF button until the SLEEP light ( goes off, then release.
- Page 16 ROUGH-IN DRAWINGS RD28 GEM-12D - Twin Coffee Brewer 22.25 in [56.5 cm] 18.00 in [45.7 cm] 29.00 in [73.7 cm] 7.00 in 5.50 in [17.8 cm] [14.0 cm] 4.00 in [10.2 cm] GEM-12D, ROUGH-IN DRAWING 11277B...
-
Page 17: Ip35
ILLUSTRATED PARTS/RECOMMENDED PARTS IP35 GEM-12D - Main Chassis - Exploded View Water tank assemblies: - see section IP36 - see section IP37 for units with capillary probe See satellite user guide for satellite replacement parts. GEM-12D, ILLUSTRATED PARTS/RECOMMENDED PARTS 051618D... - Page 18 EPDM 70 SHORE COVER, FRONT W/A GEM-12 GEM- WC-5829 12D/312IL/612ILD WC-4213-P a NUT, 5/8 LOCK PLATED WC-39197 MEMBRANE CONTRL PANEL CURTIS GEM-12D WC-4212-02 b NUT, 5/8-18 JAM PLASTIC WC-38310 LABEL, CAUTION HOT SURFACE GEN USE WC-314 POWER BLOCK, 5 STATION...
-
Page 19: Ip36
ILLUSTRATED PARTS/RECOMMENDED PARTS IP36 WC-54005 - Tank Assembly WC-54005 - Tank Assembly - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION WC-54005 TANK, COMPLETE GEM-612ILD/G12D/TL9002 WC-4382* GUARD, SHOCK HTNG ELMNT DOUBLE WC-37008 KIT, TANK LID ROUND (INCLUDES GASKET) THERMOSTAT, HI LIMIT HEATER CONTROL DPST WC-522* 277V 40A... - Page 20 ILLUSTRATED PARTS/RECOMMENDED PARTS IP37 WC-5432 - Tank Assembly WC-5432 - Tank Assembly - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION WC-5432 TANK, ASSY. COMPLETE GEM-12/GEM-312IL WC-4382* GUARD, SHOCK HTNG ELMNT DOUBLE WC-37008* KIT, TANK LID ROUND (INCLUDES GASKET) THERMOSTAT, HI LIMIT HEATER CONTROL DPST WC-522* 277V 40A...
-
Page 21: Es43
ELECTRICAL SCHEMATICS ES43 GEM-12D-10 GEM-12D-10, ELECTRICAL SCHEMATIC 111116NC... -
Page 22: Es44
ELECTRICAL SCHEMATICS ES44 GEM-12D-16 GEM-12D-16, ELECTRICAL SCHEMATIC 111116NC... -
Page 23: Es45
ELECTRICAL SCHEMATICS ES45 GEM-12D-30 ELECTRICAL RATING TABLE # of Tank Element Warmer Element Voltage Amps Wa s Hertz # of Tank Model Conductor Phase Ra ng Ra ng Elements Wires GEM-12D-30 6300 50/60 2000W/220V (2X) 100W/220V GEM-12D-30 29.9 6890 GEM-12D-30 31.2 7500 UCM Pin Assignments... - Page 24 TROUBLESHOOTING GUIDE TG15 WARNING: Electric Shock Hazard - Scald and Burn Hazard - IMPORTANT: always Valve Test Procedure Troubleshooting Guidelines • • Use this troubleshooting guide along with the appropriate ELECTRICAL SCHEMATIC. • Valve Test Procedure in either direction Water Not Hot Enough PROGRAMMING GUIDE replace the temperature sensor...
- Page 25 TROUBLESHOOTING GUIDE TG15 During Brewing By-Pass Flow Adjustment No Power - Control Panel Not Lit Water Tank Does Not Fill Brewer Does Not Start When Brew Button is Pressed All Of The Time Coffee/Tea Too Strong Dispenser Not Filled To Normal Level During Brewing...
- Page 26 TROUBLESHOOTING GUIDE TG15 Water Tank Does Not Fill IMPORTANT: Dispenser Not Filled To Normal Level During Brewing PROGRAMMING GUIDE SPECIFICATIONS sure that the spray head is correctly aligned and that the tubing is routed properly to allow for maximum water By-Pass Flow Adjustment No Water Flows From Brewer During Brewing Water Tank Does Not Fill...
- Page 27 TROUBLESHOOTING GUIDE TG15 Water Does Not Heat At All Tank Does Not Fill • Water Not Hot Enough • • ELECTRICAL SCHEMATIC) to the Water Too Hot (Boiling or Excessive Steaming) IMPORTANT: Warmer Does Not Heat NOTE...
- Page 28 TROUBLESHOOTING GUIDE TG15 By-Pass Flow Adjustment PROGRAMMING GUIDE...
- Page 29 Return Merchandise Authorization (RMA): All returned equipment must be properly re-packaged in the original carton and received by Curtis within 45 days following the issuance of a RMA. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).