GE WBVH6240 Technical Service Manual page 52

T e s t
Press
Mode
t01 Start/ Display defi nes model id (01-03). Always displays"---" when control
Pause board replaced. Proper model must be set when control board
replaced. Rotate knob until desired selection is displayed (01-03),
then press and hold Start/Pause until beep.
t02 Start/ Displays the most recent error code. (E00=none) Repeat pressing
Pause Start/Pause to display up to previous 10 error codes. Press and hold
Start/Pause to clear all error codes. (Will then display E00.)
t03 Start/ Displays software revision numbers. Press Start/Pause to alternate
Pause between COD (Control software version), EE (eeprom version), and
InV (Inverter software version).
t04 Start/ Displays and tests loops on lighting of LED'S and cycle lights.
Pause Buttons beep when pressed.
t05 Start/ Displays P and operates pump for 60 seconds, then returns to t05.
Pause
t06 Start/ Water level control test. Pump runs and displays E at start (no
Pause water in tub). Press Start/Pause to advance. Water valve begins fi ll.
Displays F when reaches FOAM level. Displays nl when reaches
MAIN level, and briefl y displays oF when reaches overfl ow level,
then pumps water out. Displays E when empty.
t07 Start/ Water heater/thermistor test. (Note: Main level switch must be
Pause functional.) Fills with water to main level, then operates heater
for up to 5 minutes. Displays temperature of water, as heated, in
degrees F. After 5 minutes, water pumps out, then returns to t07.
t08 Start/ Water valve test. Displays hOt and pump runs. Fills with hot water.
Pause Maximum level is main level switch setting. Pumps out water and
returns to t08.
t09 Start/ Water valve test. Displays Cld and pump runs. Fills with cold water.
Pause Maximum level is main level switch setting. Pumps out water and
returns to t09.
t10 Start/ Tumble test. Displays tt. Wash basket spins in one direction for 5
Pause seconds, pauses, then spins in the opposite direction for 5 seconds.
Repeats until exit initiated. (Note: Beginning direction is random.)
t11 Start/ Spin speed-low spin/high spin test. Display shows rpm. Pump runs,
Pause displays 0, then wash basket ramps to 400 rpm. Press Start/Pause
a second time to ramp to 1000 rpm. (May display 999 or 0 for 1000
rpm.) Then motor is unpowered, displays 0, pump runs, and returns
to t11.
t12 Start/ Dispenser motor/mechanism test. Press Start/Pause to advance.
Pause Displays Pdt and fi lls via prewash compartment. Displays
ddt and fi lls via wash compartment. Displays bdt and fi lls via
bleach compartment. Displays Fdt and fi lls via fabric softener
compartment. (Note: If main level reached during test, dispenser
operation stops, pump runs, and returns to t12.)
t13 Start/ EOL test sequence. Not used for service.
Pause
t14 Start/ Spin speed ramp up test. Display shows rpm. Pump runs, displays
Pause 0, then wash basket ramps to 100 rpm, pauses, ramps to 350 rpm,
pauses, then ramps to and holds at 1000 rpm. (May display 999 or
0 for 1000 rpm.)
Displays
– 52 –
Exit
Press Power.
Returns to t01
Press Power.
Returns to t02
Press Power.
Returns to t03
Press Power.
Returns to t04
Press Power.
Returns to t05
Press Power.
Pump runs.
Returns to t06
Press Power.
Pump runs.
Returns to t07
Press Power.
Pump runs.
Returns to t08
Press Power.
Pump runs.
Returns to t09
Press Power.
Pump runs.
Returns to t10
Press Power.
Pump runs.
Returns to t11
Press Power.
Pump runs.
Returns to t12
Press Power.
Returns to t13
Press Power.
Pump runs.
Returns to t14