Table of Contents
Advertisement
(
*
)
The following conditions must be satisfied:
- Material type: 3M Scotchcal Mastercut Film, ARLON Series 2100
- Special stand (a roll material must be set at the rear and on the inner sheet hanger)
- Side margins: 25 mm (1") or more for both the left and right margins
- Front margin: 25 mm (1") or more
(After loading the material, using the display menu to select "EDGE" as the material type automatically sets a front margin of 25 mm (1").)
- Use of the display menu's "AREA" function to perform feed of the material length plus 0.2 m and set the material correctly
- Cutting of the following data one time
Side margins: 25 mm (1") or more
Front margin: 25 mm (1") or more
Movable
pinch roller (left)
Movable pinch roller (right)
Interface Specifications
Standard
Input signals
Output signals
Level of input/output signals
Transmission method
Standard
Transmission method
Transmission speed
Parity check
Data bits
Stop bits
Handshake
Specification of the Parallel interface
Signal
Terminal
Signal
Number
Number
Number
NC
3 6
1 8
HIGH**
HIGH*
3 5
1 7
GND
NC
3 4
1 6
GND
GND
3 3
1 5
HIGH*
3 2
1 4
NC
3 1
1 3
HIGH*
3 0
1 2
GND
2 9
1 1
BUSY
2 8
1 0
ACK
2 7
9
2 6
8
2 5
7
GND
2 4
6
2 3
5
2 2
4
2 1
3
2 0
2
1 9
1
STROBE
32
Cutter
protector
Origin
Y
Side margins:
Feed length
X
25 mm (1")
Sheets with a width exceeding 610 mm (24"): 4,000 mm (157-7/16")
or more
Sheets with a width of 610 mm (24") or less : 8,000 mm (315-15/16")
The origin is rotated 90 degrees ("AXIS" on the display menu is set to "90deg").
In compliance with the specifications of Centronics
STROBE (1 BIT), DATA (8 BIT)
BUSY (1 BIT), ACK (1 BIT)
TTL level
Asynchronous
RS-232C specifications
Asynchronous, duplex data transmission
2400, 4800, 9600, 19200 (selected using panel keys)
Odd, Even, or None (selected using panel keys)
7 or 8 bits (selected using panel keys)
1 or 2 bits (selected using panel keys)
DTR or Xon/Xoff (selected using panel keys)
Pin Connection
18
1
NC
NC
36
19
D7
D6
+5 V
Ω
3.3K
D5
=
*
D4
+5 V
D3
Ω
100
D2
=
**
D1
D0
(1)
The letters are cut in order starting with "R"
(2)
After the last letter ("P") has been cut, the machine returns to the origin
point and the outer border is cut
Parallel
Serial
Specification of the Serial interface
Signal
Terminal
Number
Number
NC
2 5
1 3
NC
2 4
1 2
NC
2 3
1 1
NC
2 2
1 0
NC
2 1
9
DTR
2 0
8
NC
1 9
7
NC
1 8
6
NC
1 7
5
NC
1 6
4
NC
1 5
3
NC
1 4
2
1
Cut length
Fills the
hard clip
Signal
Pin Connection
Number
NC
NC
NC
13
NC
NC
NC
SG
25
DSR
CTS
RTS
RXD
TXD
FG
1
14
Hide quick links:
Advertisement
Table of Contents
