Table of Contents
Advertisement
PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
-=:>
Wire or insulate the speaker cable
properly and press the reset button. If
the "PROTECT" code does not disappear,
consult your nearest service center.
NA FILE:
COpy PRO:
An Audio file is played with a format that this
unit can't support.
A copy-protected file is played.
HF DISCONCT: The unit cannot communicate with the cell-
phone.
HF ERROR 07:
The memory cannot be accessed.
-=:>
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF ERROR 68:
The unit cannot communicate with the cell-
phone.
-=:>
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
READ ERROR:
The file system of the connected USB device
is broken.
-=:>
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
USB REMOVE (Blink)
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
NO NUMBER:
0
The calling party does not notify a caller
10.
o
There is no phone number data.
The faceplate of the slave unit being
connected to this unit has been removed.
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be
recognized.
Pairing error.
NO PANEL:
TOO SOFT:
TOO LOUD:
TOO LONG:
PAIRING NG:
FAV: NO MEMORY:
The procedure is not registered to Favorite
Preset Memory
NO ACCESS:
The procedure preset with Favorite Control
cannot be available. The preset content may
not be recalled depending on the selected
source or mode.
NO MATCHING: The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
NO VOICE:
No call.
NO PHONEBOOK:
Data is not contained in the phone book.
NO MESSAGE:
No short message in In Box.
NO RECORD:
The voice tag is not registered in the
phonebook.
MEMORY FULL: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
DEVICE FULL:
5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN CODE NG: The PIN code is wrong.
CONNECT NG: The unit cannot be connected to the device.
UNKNOWN:
The Bluetooth device cannot be detected.
Connection to the iPod has failed.
-=:>
Remove the USB device and then
reconnect it.
-=:>
Confirm that the software for the iPod is
the latest version.
iPod ERROR:
USB ERROR:
NO MUSIC DATA/ERROR 15:
o
The connected USB device contains no
playable audio file.
o
Media was played that does not have data
recorded that the unit can play.
Some trouble may have occurred to the
connected USB device.
-=:>
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
NO DEVICE:
The USB device is selected as a source
although no USB device is connected.
-=:>
Change the source to any source other
than USB Connect an USB device, and
change the source to USB again.
N/A DEVICE:
0
An unsupported USB device is connected.
o
Connection to the iPod has failed.
-=:>
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 36) for information on supported
iPods.
NO DATA:
NO ENTRY:
o
There is no outgoing call list.
o
There is no incoming call list.
o
There is no missed call list.
o
There is no phone book list.
The cell-phone has not been registered
(pairing).
HD MEM FULL: The tag memory of HD Radio is FULL.
iPod MEM FULL:
The iPod memory is FULL.
NO TAG FNC:
iPod which does not support the tag memory
is connected.
English I
45
Hide quick links:
Advertisement
Table of Contents
