Service Adjustments - Sanyo DS13204 Service Manual

GENERAL
This set has an on-screen Service Menu system included in the CPU that allows remote operation for most of the service adjustments.
To enter the Service Menu, first disconnect the AC power cord. Then while pressing the MENU key on the front control panel, recon-
nect the AC power cord. The adjustments can now be made with the remote control or front control panel keys.
ON-SCREEN SERVICE MENU SYSTEM
1. Enter the Service Menu:
•
While pressing the MENU key on the front control panel, reconnect the AC
power cord. The Service Menu Display will now appear. (See Figure 1.)

2. Service Adjustments:

•
Press the or key to select the desired service menu item you want to
adjust. (See page 4 for On-screen Service Menu.)
•
Use the + or – key or number keys to adjust the data.
The + or – keys will increase or decrease the data sequentially.
The number keys (0 ~ 7) toggle only their respective bits between 1and 0.
3. Exit from the Service Menu:
•
Press the MENU key to turn off the Service Menu display.
IC802 (EEPROM) REPLACEMENT
When IC802 (EEPROM) is replaced, IC801 (CPU) will automatically write the initial reference data into IC802 for basic TV operation.
However, the bus data should be checked and some bus data should be set up before attempting the service adjustments.
(See pages 4 – 5 for detailed information.)
INITIAL BUS DATA SETUP
Note: When IC802 (EEPROM) is replaced, change the following initial reference data for proper TV operation before
attempting the service adjustments.
1. Disconnect the AC power cord (AC 120V line).
2. While pressing the MENU key on the front control panel, reconnect the AC power cord.
The Service Menu display will now appear.
3. Select No. 3C SCO (Sub Color) with
4. Select No. 3D STI (Sub Tint) with
5. Select No. 3F SSH (Sub Sharpness) with
6. Select No. 41 HBS7HP (H Blanking / H Phase) with
7. Select No. 42 VS (V Size) with
8. Select No. 43 VSP7VPO (V Sync Sep / V Position) with
9. Select No. 44 GRY7CRS5VLN (Gray / Cross B/W / V Lin) with
10. Select No. 45 HBL5VSC with
11. Select No. 46 VC3CDM (V Size Comp / V Count Down), with
12. Select No. 4B BGS5RGD4GD (Bγ / RGγ / G Drive) with
13. Select No. 4D SBI (Sub Bias) with
14. Select No. 56 FBP6WP4PRE2CRG (FBP Blanking / White Peak / Pre shoot / Coring Gain) with
with + or – key for 42 (hex).
15. Select No. 57 DCR4BSS2BSG (DC Reset / Black Stretch Start / Black Stretch Gain) with
+ or – key for 02 (hex).
16. Select No. 58 AFC7CBP5 (Auto Flesh / Color BPF Bypass) with
17. Select No. 60 HBL5 (H Blanking Left) with
18. Select No. 83 OPT (AV Option) with
19. Select No. 8D HR (H Display Position) with
20. Select No. 8E SBO (Sub Bright Offset) with
21. Press the MENU key to turn off the Service Menu display.
SERVICE ADJUSTMENTS
or key. Adjust the data with + or – key for 1D (hex).
or key. Adjust the data with + or – key for 08 (hex).
or key. Adjust the data with + or – key for 05 (hex).
or
or key. Adjust the data with + or – key for 45 (hex).
or key. Adjust the data with + or – key for EA (hex).
or
or key. Adjust the data with + or – key for 40 (hex).
or key. Adjust the data with + or – key for 00 (hex).
or key. Adjust the data with + or – key for 84 (hex).
or key. Adjust the data with + or – key for 10 (hex).
or key. Adjust the data with + or – key for 00 (hex).
— 3 —
ITEM NO.
key. Adjust the data with + or – key for 10 (hex).
or key. Adjust the data with + or – key for 0F (hex).
or key. Adjust the data with + or – key for 92 (hex).
or key. Adjust the data with + or – key for 38 (hex).
key. Adjust the data with + or – key for 0B (hex).
or key. Adjust the data with + or – key for 80 (hex).
TITLE
3C SCO
0A 00001010
BINARY DATA
(8 bit)
HEX DATA
Figure 1. Service Menu Display
or key. Adjust the data
or key. Adjust the data with