Keypad Functions - Honeywell ADEMCO LYNXR Series Installation And Setup Manual

System Operation

Keypad Functions

The keypad allows the user to arm and disarm the system, and perform other system functions, such as
bypassing zones. Zone and system conditions (alarm, trouble, bypass) are displayed in the display window.
When an alarm occurs, keypad sounding and external sounding will occur, and the zone(s) in alarm will be
displayed on the keypad. Pressing any key will silence the keypad sounder for 10 seconds (only once).
Disarming the system will silence both keypad and external sounders. When the system is disarmed, any
zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To
clear this display, simply repeat the disarm sequence (enter the security code and press the OFF key). The
keypad also features chime annunciation, and 3 panic key pairs for silent, audible, fire or personal
emergency alarms. These keys can notify the central station of an alarm condition, if that service is
connected. A summary of system functions is provided below for more detailed information refer to the
User's Manual.
Security Functions
(Empty boxes represent the user's security code)
Checking system status:
To arm in STAY mode:
To restart exit delay:
To arm in AWAY mode:
To arm with NO DELAY:
To arm if Quick Arm is programmed:
To disarm the system and silence alarms:
To bypass a zone(s):
To turn Chime mode on or off:
Message Center
To record a message:
FUNCTION
To stop recording before end of 20 seconds:
To play back a message:
To skip a message: [✻]
To delete all messages:
Volume Control
To adjust message playback/system announcement volume:
To mute system announcements:
To restore/unmute announcement & volume:
Other Functions
To set the time and date:
To set the scheduling:
To activate or deactivate X-10 devices 1-6:
To activate or deactivate X-10 devices 7 & 8:
To add a user code:
To delete a user code (except Master Code):
To turn Test mode on:
To turn Test mode off:
To use the defined AUX function:
To define AUX function:
To send message to pager:
To program Follow Me Announcement telephone number
(high level messages); press
STATUS
+
STAY
(applies only if system is armed in Stay mode)
STAY
+
AWAY
+
AWAY
or
AWAY
+
BYPASS
+
FUNCTION CHIME
+
RECORD
OFF
+
PLAY
FUNCTION
+
(during message replay)
FUNCTION DELETE
+
FUNCTION
+
FUNCTION
+
FUNCTION
FUNCTION
*
+
CODE
+
TEST
+
OFF
Press and hold
+
FUNCTION
Press and hold key 2 seconds (4 beeps)
AUX
again for secondary messages
STATUS
(or installer code + [3])
(or installer code + [2])
or +
STAY NO DELAY
(hold down for at least 2 seconds)
STAY
+
OFF
+ 2-digit zone number(s)
If a 5827 Wireless keypad has been installed, it cannot be used to
activate message playback/recording, programming the real time clock
or scheduling remotely. In this case, you must use the master keypad on
the control panel to perform these functions.
FUNCTION
+
VOLUME OFF
+ + [3] or [6]
FUNCTION VOLUME
+ [63]
+ [64]
+ or
LIGHTS ON LIGHTS OFF
+
FUNCTION
+ user number + user's code (*master code)
*+ + user number (* master code)
CODE
key 2 secs (4 beeps) +
AUX
+
+ action separated by +
AUX
:
–48–
NOTE
+
FUNCTION RECORD
+ + [3] or [6]
VOLUME
+ device number
or
+
LIGHTS ON LIGHTS OFF
terminated by +
AUX
+ + [65]
FUNCTION
.
+ dev. No
+
AUX AUX