Page 1
Record the serial number, found on the back of the unit, In the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
Safetv Precautions 1 AWARNING To prevent injury and/or fire, take the If you experience problems during installation, consult your Kenwood dealer. following precautions: If the unit does not seem to be working right, try Ensure that the unrt is securely installed.
Monitor Control Function _-_xxx.._^^^_,. .^.^... Picture Quality Adjustment Screen 1 MODE SCRN Phbne Jack (03.5) Each time yoci press the V.StL button tor at least Turning on the power one second, the burlt-In speaker mode switches as Press the PWR button. follows Turning off the power...
Page 5
<On Screen Display> If the monitor’s buttons operated while a TV, video or navigation picture is displayed, the receiving channel No., the picture settings, AV output settings, etc., are superimposed on the picture Tuning mode Channel No. TV band Screen mode Speaker volume level Speaker mode...
Page 6
Svstem Setw Function A MODE SCRN Phone Jack (03.5) When the Video Box Unit is connected 1 Press the SCRN button for at least one second to switch to the setup menu screen. 2 Touch [ SYSTEM I to switch to the system setting screen.
Page 7
Setup Menu Screen < Video Box Unit or KTC-VBOON> Setup Menu Screen < KTC-VIOOP > Setting the Touch Sensor Tone [BEEP] Touch [ ON 1 or I OFF 1 to switch the functron on and off. Select the area for video broadcast viewing.
Page 8
n/ COntrd Function c When The KTC-V8OON/KTC-V8OOP is connected > picture screen Control Screen You can store 8 statrons in eacp of the TV1 and TV2 preset bands. 1 Press the V.SEL button repeatedly to select the TV picture. 2 Touch the part @ to swatch to the TV control screen. You can automatically sto&...
Page 9
Selecting the Preset Bands Each trme you touch part 8, the preset band switches between the TV1 and TV2. Selecting the Channels Auto Seek Tuning (AUTO11 Touch the part @ to seek for channels up the band. Touch the part @ to seek for channels down the band.
AV OUT button Each time you press AV OUT button to switch the AV output mode. (Switching the AV Output- see P.5) TV Control Function KENWOOD SEEK button REMOTE CONTROL “NIT RC-210 Each time you press the SEEK button, the tunrng tnode switches...
Page 11
lnstalla tion External view External view External view Number of items ..Number of items Number of items (04xi2mm) @I $@@ * @ <04xl6mm) To prevent short clrcults, remove the key from the Be sure to use the supplied screws for lgnitlon and dtsconnect the 0 terminal of the battery.
Installation Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A. Do not install in locations where the entrre support IS at a diagonal such as in Figure I3 or where the monrtor unrt is facing down such as in Figure C.
Page 13
n Securing to audio board n Securing to pile carpet Peel the protective strips off of the velcro Accessory (_S strips, attach them to the bottom of the (04x 16mm) hideaway unit, and secure to the pile carpet [ ACAUTION Please do not Install the unit near the dashboard, the rear tray, or other important components.
Page 14
Installation n Connecting the Headphone Headphone W Connecting the AV Equipment KENWOOD ’ Q Audio/Visual Output :.w-* Audio right output (Red) i-~~-~-.~--* Audio left output (WhItei ....““..~ “,sua, output (Ye,iow,...
AM/FM radio reception IS poor The TV antenna and vehrcle’s radro antenna Separate the two antennas as far as possrble. and/or there IS norse are too close Turn off the LZ-800W. (When the KTC-V800N or KTC- V8OOP IS connected)
Specifications Specifications subject to change without notice. Monitor Unit .8.0 inches wide Screen size ......................... 176.4(W) x 99.2(H) x ZOZ(Diagonal) mm 6-15/1+6(W) x 3-7/8(H) inch Transparent TN LCD panel Display system .................... Drive system....................TFT active matrix system .336,960 pixels (480 H x 234 V x RGB) Number of pixels ...............
Page 17
EXCEPTION: Refurbished units sold by Crutchfield Corporation have a 90-day warranty. The customer must provide a copy of the original sales receipt from a Kenwood authorized dealer showing the customer’s name, address, phone number, dealer location, date of purchase, and model number.
Page 18
Refurbished Dealer Stock Units There are no RA privileges on R-stock units and any R-stock units returned to Kenwood for credit will be refused and returned to the dealer. However, a Kenwood dealer may submit a stock unit for warranty repair within 90 days after purchase from Kenwood or Kenwood’s authorized distributors if the following...