Programminga Master Power Key With Instant Channel Selection; Clearing A Macro - Radio Shack 8-IN-ONE REMOTE Owner's Manual

USING MACROS
P A F C
ROGRAMMING AVORITE HANNEL
3. Press SELECT once to begin programming. [SEL MACKEY]
appears.
4. Select a key you want to use as a macro and press it once.
[ENTER SEQ] appears.
5. Enter a macro sequence of up to 15 keys. For our example,
press the following keys once in this order: TV - 7 - 1.
NOTE: If you have access to over 100 channels, add a 0 before the
channel numbers (e.g., 0 -7 - 1). If the original remote control
required pressing an Enter key to change the channel, also press
ENTER after the channel number (e.g., 0 - 7 - 1 - ENTER).
NOTE: An [ERROR] message, followed by [MAX = 15] alerts you
that the macro sequence must be 15 keys or less.
After pressing the first key (in the macro sequence), [SEL TO
END] appears as a reminder to use SELECT to end the
sequence (see next step).
6. To end the macro sequence, press and hold SELECT until
[SUCCESS] appears, followed by [EXIT SETUP]. The remote
will automatically exit the programming mode and return to
normal operation.
Now when you press the key with this assigned macro, you will instantly see
cable channel 71 on your TV set.
P A M P
ROGRAMMING ASTER OWER
C S
HANNEL ELECTION
A macro key can be programmed to turn on and off your devices as well.
For example, let's set up a sequence that will turn on the TV and tune it to
channel 3, and then turn on the cable converter and tune it to a premium
channel (e.g., 11).
NOTE: This example assumes all equipment is turned off and that the TV is con-
nected through the cable converter with TV tuning set to channel 3.
1. Perform steps 1 through 4 of the previous section,
Programming A Favorite Channel, that starts on the previous
page. However, this time in step 4, substitute another key for
use as a macro key.
14 Using Macros
8- -O R
IN NE EMOTE
(C )
ONTINUED
K W I
EY ITH NSTANT
2. Enter a macro sequence of up to 15 keys. For our example,
press the following keys once in this order: CBL - POWER -
TV - POWER - 0 - 3 - CBL- 1 - 1
NOTE: If you have access to over 100 channels, add an
set of channel numbers (e.g., 0 - 0 - 3 and 0 - 1 - 1). If the original
remote control required pressing an Enter key to change the channel,
also press ENTER after each channel number (e.g., 0 - 0 - 3 - ENTER
and 0 - 1 - 1 - ENTER).
NOTE: An [ERROR] message, followed by [MAX = 15] alerts you
that the macro sequence must be 15 keys or less.
3. After pressing the first key (in the macro sequence), [SEL TO
END] appears as a reminder to use SELECT to end the
sequence (see next step).
4. To end the macro sequence, press and hold SELECT until you
see [SUCCESS] appear in the display, followed by [EXIT
SETUP]. The remote will automatically exit the programming
mode and return to normal operation.
Now when you press the key with this assigned macro, the cable converter
and TV will turn on, the TV will tune to channel 03, and then the cable
converter will tune to channel 11.
C A M
LEARING ACRO
1. Perform steps 1 through 4 of the earlier section,
Programming A Favorite Channel., that starts on the previ-
ous page. However, this time in step 2, select a macro key
you want to be cleared.
2. Press and hold SELECT to clear the macro key. [SEL TO END]
appears as a reminder to use SELECT to end the sequence
(see next step).
3. Press SELECT until [SUCCESS] appears, followed by [EXIT
SETUP]. The remote will automatically exit the programming
mode and return to normal operation.
0
before each