Preparing For Surround Sound; Speaker Settings - Kenwood VR-6050 Instruction Manual

Preparing for surround sound
Speaker settings
To enable you to obtain optimum enjoyment from the receiver's llstenlng
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below
POWER
ON/STANDBY 0
(VR.6050) /
ON/STANDBY 0
(KRFV7060DN6060D) SETUP MULTI CONTROL
POWER ON/OFF
(KRF47060LVV6060D)
SET UP
Joystick
(MULTI CONTROL
DOWN./UP,)
.AlT,
q
Turn on the power to this receiver by pressing the POWER
ON/STANDBY (?, (for VR-6050) or POWER ON/OFF and ON/
STANDBY o (KRF-V706OD/V606OD) or POWER 0 key.
a Press the SETUP key to enter the SET UP mode and press
A/V keys or Joystick (r/w) for the following displays.
L
i SPSETUP
52' TEST TONE
\C SP DISTANCE
~9 DISP MODE
s, EXIT
The flow of the SET UP IS as follows
t
[SP SETUPH TEST TONE
SP DISTANCE DISP MODE
4
i 4
-cS"bWOOf%
%
T.TONE T TONE
Fro",
%
center
%
S"rro"nd
%
s"A%n"
%
YIYd
%
+SUbV&
a Select a speaker system.
0 Select the SP SETUP and press the SETUP key again so
that the subwoofer setting indication "SUBW ON" appears.
0 Use the MULTI CONTROL knob or Joystick (A/V) to select
the appropriate subwoofer setting.
I:
I SUBW ON : Subwoofet setting mode to the receiver IS
ON
2 SUBW OFF : Subwoofer setting tmode to the iecelver IS
OFF
l
The Initial setting IS "SUBW ON"
l
When the setting "SUBW OFF" IS selected, the front speakers
are auton?atlcally set to "FRNT LARGE" and the Iprocetlure skips
to step 0
Before step 0, press the SETUP key to accept the setting
l
When subwoofer output sound IS required, select "FRNT
NORMAL" or select both "FRNT LARGE" and "SW RE-MIX ON"
0 Press the A key or Joystick I,) to accept the setting.
l
The front speakers setting Indlcatlon "FRNT" appears
0 Use the MULTI CONTROL knob or Joystick
(A/T)
to select
the appropriate front speakers setting.
c
1 FRNT LARGE
Large front speakers are connected
to the receIveI
2 FRNT NORMAL
Averageslreflont speaketsaiecoi?-
netted to the lecelvel
l
For "FRNT LARGE" selection, no sound ~111 be lheard fron?
subwoofer speaker even when It IS set to ON However, If you
select SPEAKER EQ mode when subwoofer IS selected, you
WIII be able to hear sound from the subwoofer
When II- STEREO mode, the soilnd goes directly to front
speaker
0 Press the r\ key or Joystick (w) to accept the setting.
l
The center speaker setting lndvzatlon "CNTR" appears
0 Use the MULTI CONTROL knob or Joystick (A/V) to select
the appropriate center speaker setting.
If you selected "LARGE" as the front speakers setting,
1 CNTR LARGE
A large center speaker IS connected
to the receive,
2 CNTR NORMAL An average size center speaker IS
L 3 CNTR OFF
connected to the receiver
Center speaker setting tmode to the
receiver IS OFF
If you selected "NORMAL" as the front speakers setting,
c
I CNTR ON : Center speaker setting mode to the re-
cerver IS ON
2 CNTR OFF : Center speaker setting niooe to the re-
cerver IS OFF
0 Press the A keys or Joystick (b) again to accept the setting.
*The surround speaker setting lndlcatlon "SURR" appears
0 Use the MULTI CONTROL knob or Joystick (A/V) to select
the appropriate surround speaker setting.
If you selected "LARGE" as the center speaker setting,
1 SURR LARGE
2 SURR NORMAL
3 SURROFF
Large surround speakers are con-
nected to the lecelver
Average size su~~ouncl speakers are
connected to the receIveI
Surround speaker setting mode to
the receIveI IS OFF
18EN