Directed Electronics SmartStart 5000-series Owner's Manual page 35

0 201 r Directed Electron ics. All rights Resel"\led
Note: When doing any prog ramm ing w ith secu rity features off, the horn function
(feature menu 1 item 131 must be programmed as Si ren function to get on audible
confirmation from the un it
The System Featu res L earn Routine dictates how the un it operates. It is possible to
access and change most of the feature settings using the control center button.
1 .
Open a door
2
Turn the ignition on, then off.
3.
Select a 1\1\enu. Press and hold the control center button . The number
of
siren
chirps indicates the menu number.
1
chirp indicates menu
1, 2
chirps- menu
2
and
3
chi rps for menu
3
4. When the desired menu chi rps o re hea rd, release the control center button.
5.
Select a Feature. Press and release the control center button the numbe r of
times corresponding to the feature you wish to change . Then press and hold
one more ti me to select the fea tu res.
6
Program the Feature. Wh ile holding the Control center button. you ca n
program the feature using the remote control
For features with only tvvo options;
~
= oRtion
1
w hile • =option
2.
For features w ith more thon tvvo options; • selects the optio ns in ascendi ng order.
Once
o
feature is programmed:
O ther features can be programmed within the same menu
Another menu con be selected
The learn routine can be exited if progra mming is complete
To access another feature in the some menu:
1 Press and release the control center button the number of times necessary to
advance from the feature you just programmed to the next one you want to
prog ra m
2. Then press the con trol center button once more and hold it
To select another menu:
1.
Press and hold the control center button .
2 After 3 seconds, the unit advances to the next menu and the si ren ch irps, indi-
cating wh ich menu has been accessed
The learn routine exits if any of the following occurs:
The open door is closed
The ignition is turned On
There is no activity lor
30
seconds
The control center button is pressed too ma ny times
Security Features Disable/Enable
The system has the abil ity to function as a security/remote start system or keyless/
remote start system by enabling or disabling secu ri ty. The default setti ng is Enabled.
To prog ram the fea ture .
1
Open a door.
2.
Turn the ign ition on , then off.
3.
Press and hold the control center button until the LED flashes
3
times and the
siren (if connected} ch irps
3
times.
4
Release the control center button .
Note: If the control center button is released and then pressed aga in, the sys·
tem w ill enter the fea tures progra mm ing menus.
5.
Within
15
seconds, simultaneously press the
~
and • buttons of o pro-
grammed remote control.
6
The siren (if con nected) wil l chirp and the pa rking lig hts w ill flash as listed
below
1
flash/chirp: Secu rity featu res d isa bled
2 flashes/ chirps: Security features enabled
Security Fea tures Disabled w il l disable all secu rity operations of the system, includ ing
but not limited to those listed below:
Multi L evel Arming
Sensor Warn-away
Full Trigger Operation
Armed Wh ile Driving
Automatic Eng ine Disable
Note: Disabled featu res with progra mmable options con still be prog ram med manu-
ally or with the Bitvvriter but will not operate until the Security Featu res have been
enabled .
The Security Features Disable/ enable routi ne exits if the fol lowing occurs :
The open door is closed
The ignition is turned on
There is no activity for
15
seconds
The control center button is pressed too many times
Bitwriter_, _ Only_QpJio.os ___ _
H
If programm ing w ith the Bitwriter®, the learn routine can be locked or un-
locked. If the learn routine has previously been locked , it must
be
unlocked
with Bitvvriter® - this can not
be
done ma nually w ith the control center but-
too
The Bitvvriter®
M
g ives you access to a wider ra nge of system options. These
features and
th~justments
that may be programmed o re desc ribed in the table
below
Note: The "Zap" fea ture on the Bitwriter does not reset the Virtual tach or secu rity
fea tures enabled/disabled settings
Red 4-pin port, Bitwriter/ESP2 or 020 programming
The Red 4-pin plug may be configu red as a Bitwriter/ESP2 or D2D port
The factory default is Bitvvriter/ ESP2 mode.
To use
as D2D
mode follow the below steps:
1.
Make su re Wh ite/Blue activation w ire is grounded
2. Power the un it up. The system LED flashes for 5 seconds to confirm D2D mode
change.
3.
Remove the Wh ite/ Blue w ire from ground
To change from 020 to Bitwriter /ESP2 mode:
1
Make su re the Whi te/Blue activation wi re is g rounded
2 Power the un it up, the system L ED turns on solid for 5 seconds to confirm Bit-
writer/ES P2 mode change
3. Remove the White/Blue w ire from g round.
The procedure con
be
repeated to togg le from one mode to the other
Important: If you power up the system w ith the White/Blue activa tion
w ire ungrounded, the system L ED wil l come on solid for
5
seconds indi-
cating the system is in Bitvvriter/ ESP2 mcx.le.
Ee.atur:e_Menus ______ _
~-- -~-----
Default settings o re in bold type
Menu l - Basic
Manu '
One·chirp setting
flem
Two-chirp
setting
Q1NDSS500m l1-11
2
LAD00603