Directed Electronics SmartStart 5000-series Owner's Manual page 34

Qwc e
5000-series Security and Remote Start System
Wiring Connections
*
The door trigger w ire will sti ll need to
be
connected
if
the system is prog ra mmed
w ith
security features
OFF
to
al low the system to enter the programming modes.
Antenna/Receiver
H4 AUX 4/Horn, 2-pin connector
(-) 200m A AUX 4 OUTPUT
( · ) 200 mA HORN OUTPUT
102011 DirectedEiectronics.AIIrightsReserved
I
L
Control Center button• input (use blue 2-pin
connector from Control Center cable)
Con trol Cen ter LED output (use white 2-pin
connector from Control Center cable)
• Also referred to as Valet/Program button
*The ribbon harness connects to the heavy gauge relay satellite.
Installation Points
A~usting
the Shock Sensor
Important! Make sure the vehicle is disarmed. The shock sensor sensitivity can be
adjusted
by
using a trimmer tool to turn the poten tiometer.
Adjusting the sensor:
1 Disarm the system, turn the ignition Off.
2 . W ith the sensor mounted in its permanent location, locate the trim
pot on
the
shock sensor module and using a trimmer tool:
Turn the potentiometer clockwise for increased sensitivity or
Turn
it
counterclockwise for decreased sensitivi ty
Note: You con test the new setling by cautiously impacting the vehicle with in
creasing intensity while noting the LED status on the shock sensor. The LED turns
on for a short duration for sma ll impacts befor e turning off (indicati ng a worn·
away trigger]. The impact level requ ired to fully trigger the alarm is indicated
when the LED rema ins on for a longer duration before turn ing off.
Tach Learning
To learn the loch signal:
1 Start the veh icle with the key.
2. W ithin 5 seconds, press and hold the control center burton.
3. Aher 3 seconds the LED will light constant when the tach signa l is learned
4 Release the control center button.
Important: Th is unit con learn the tachometer with the analog input or
through D2D us ing on interface module. The un it confirms which sou rce
is used.
When programming tach learning with:
Analog, the parking lights flash one time
020 inerfoce module, the parking lights flash twice
If
the tachometer input on the system is connected to the veh icle, the D2D tachometer
input w ill be ignored
Ykt.uilladt_ _ _ _ _
~-------
Note: Virtual tach is not recommended for diesel trucks
To program Virtual Tach:
1 Aher the insta ll is complete, remote start the car.
2. If the co r does not sta rt on the firs t atlempt, let the remote start attempt aga in
3 Once the cor starts, let it run unti l the pa rking lights come on
4 . When the parking lights come on, shut off the remote start w ith the remote
that's it! Virtua l Tach is programmed
Virtual Tach handles d isengaging the starter motor during remote sta rting - it does
not address over-rev.
If
the customer wonts to hove the over-rev protection copobil·
ity, the tach wire must be connected. Th is may involve more insta llation shop
charges than initia lly quoted
Important: If the Virtual Tach mode over cranks o r doesn 't crank the
vehicle long enough to sta rt and run the cor, use the Bitwriter to odd o r
subtract the starter output ti me. You con ad just the output ti me in inc re-
men ts o f 50msec of the learned time using the Bilwriter
Re5eLandJleletion _ _
~--~----~-
If a feature/virtual tach needs to be reset o r the remote contro ls need to be deleted,
use the following procedure.
Open a door. (The GREEN w ire, H 1/8, or the VIOLET, H 1/6 must be con-
nected.(
2.
Turn the ignition to the ON posi tion (The heavy gouge p ink wire must be con-
nected}.
3.
Within 10 seconds, press and release the control center button: 2 times if you
won t to delete remotes, 3 times to reset features o r 4 times to reset virtual tach
These features are described next.
Delete remotes: This feature erases all remotes from the memory of the
security system. This is useful in cases when a customer's remote is !ost
or stolen.
Note: This does not reset the programmed features of the security system
or reset the Virtua l Tach setti ng.
Reset Features: Th is resets oil features of the security system to the factory
default settings.
N o te: Th is feature does not delete the remotes from the security system
or reset the Virtual Tach setting or security features enabled/ d isabled
settings
Virtual Toch Reset: Deletes all previously learned values for Virtual Tach,
and on the next remote start sequence the un it begins virtual tach initial-
ization.
Note : The "Zap" fea ture
on
the Bitvvriter does not reset the Virtual tach
setting
4 Once you have selected the func tion step, press the control center button once
more and hold it. The LED flashes and the siren ch irps to confirm the selected
functiona l step. Do not re lease the control center button
5. Wh ile hold ing the control center button , press the
Q
button on the remote
control. The unit chirps to confirm that the feature has been successful ly reset.
Once the feature is reset, the control center button can be released.
Rernote..£tart Shutdown Diagnostics__
To perform shutdown diagnostics:
1 With the ignition Off, press and hold the control center button.
2. Turn the ignition On a nd then back O ff wh ile holding the control center
button
3. Release the control center button.
4 . Press and release the control center button. The LED fl ashes to report the last
shutdown for one minute or until the ign ition is turned on, as shown in the
fol lowing table:
LED Flashes
I flash
Shutdown Mode
Timed o ut
Over-rev shutdown 2 flashes
3 flashes
4 flashes
5 flashes
6 flashes
7 flashes
8 fla shes
Low or no RPM, low battery [voltage and virtue! tach modes]
Tra nsmitter shutdown [or optional push button)
1-1
Hood Shutdown IH3/4 GRAYI
1+1 Shutdown IH3/3 BROWN]
1-1
Neutc ol safety shutdown IH3/l BIACK/WHITEI
Wait-to-start timed out
Bitwriters wlth a date code
of 6a
or older require on IC
upgrade lp/ n 998MI. Some b itw-riters w ith a dote code
of 6 B do not requ ire the IC upgrade, refer to tech tip #
I I 12 for more information
·-------=- .
Eil
11;!1
The Bit-writer® (p/ n 998U)
requires chrp version 2.7 or
newer to program this unit
See full Insta llation Guide lor more
detailed info rmation on this system
Such information a nd more con be
found on line a t
E L E C T R 0 N I C S
www.directechs.com