Directed Electronics Hornet 564T Installation Manual
  1. Manuals
  2. Brands
  3. Directed Electronics Manuals
  4. Remote Starter
  5. Hornet 564T
  6. Installation manual
Directed Electronics Hornet 564T Installation Manual

Directed Electronics Hornet 564T Installation Manual

Directed electronics remote start system installation guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

M M o o d d e e l l 5 5 6 6 4 4 T T
I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e
H H o o r r n n e e t t
NOTE:
This product is intended for installation by a professional installer only!
Any attempt to install this product by any person other than a trained professional
may result in severe damage to a vehicle's electrical system and components.
© 2005 Directed Electronics, Inc. Vista, CA
N564T 01-05

Advertisement

Table of Contents
loading

Related Manuals for Directed Electronics Hornet 564T

Summary of Contents for Directed Electronics Hornet 564T

  • Page 1 This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2005 Directed Electronics, Inc. Vista, CA N564T 01-05...

  • Page 2: 2005 Directed Electronics, Inc. Vista, Ca

    1 1 0 0 3 3 T T Keypad. Refer to the 103T requires chip version 1.5 or newer to program this unit. Owner’s Guide for details. K K e e y y p p a a d d © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 3 ................3 3 1 1 © 2005 Directed Electronics, Inc. Vista, CA passlock I and passlock II (PL-1 and PL-2) .
  • Page 4 This testing should be performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

  • Page 5: Before Beginning The Installation

    ■ When testing, don’t forget that this system is equipped with Nuisance Prevention Circuitry™(NPC™). NPC can bypass trigger zones, making them appear to stop working. See the Nuisance Prevention Circuitry section. ■ Review and complete the Safety Check section of this guide prior to the vehicle reassembly. © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 6: 2005 Directed Electronics, Inc. Vista, Ca

    ■ When mounting the control module, try to find a secure location that will not require you to extend the harnesses’ wires (they are 1.5 meters long). Keep it away from the heater core (or any other heat sources) and any obvious leaks. © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 7: 2005 Directed Electronics, Inc. Vista, Ca

    N N O O T T E E : : In many vehicles, tying the sensor to a steering column or screwing it to metal will result in poor sensitivity, especially at the rear of the vehicle. © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 8: 2005 Directed Electronics, Inc. Vista, Ca

    ■ It is easiest to remove a small panel, such as a switch blank or a dash bezel, before drilling a ■ Use quick-disconnects near the LED wires if the panel is removable. This lets mechanics or other installers remove the panel without cutting the wires. -inch hole. -inch hole. © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 9: 2005 Directed Electronics, Inc. Vista, Ca

    I I M M P P O O R R T T A A N N T T ! ! Do not remove the fuse holder on the red wire. It ensures that the control module has its own fuse, of the proper value, regardless of how many accessories are added to the main power feed. © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 10: 2005 Directed Electronics, Inc. Vista, Ca

    6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not turn over, you have the right wire. 1 1 0 0 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 11: 2005 Directed Electronics, Inc. Vista, Ca

    6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct wire and the wire's polarity is positive. © 2005 Directed Electronics, Inc. Vista, CA 1 1 1 1...

  • Page 12: Finding A (+) Parking Light Wire

    ■ At the dome light: This may not be your best choice if the vehicle has delayed domelight supervision, but it will work in many Hondas, or any vehicle with completely diode-isolated pin switches. 1 1 2 2 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 13: 2005 Directed Electronics, Inc. Vista, Ca

    If you use tapping connectors such as 3M T-Taps (not to be confused with Scotch-Locks), avoid using them in higher-current applications (constant 12V, ground, etc.). Some tapping connectors are inferior in quality and should be avoided. © 2005 Directed Electronics, Inc. Vista, CA 1 1 3 3...

  • Page 14: 2005 Directed Electronics, Inc. Vista, Ca

    ( ( - - ) ) F F A A C C T T O O R R Y Y D D I I S S A A R R M M © 2005 Directed Electronics, Inc. Vista, CA N N O O T T U U S S E E D D...

  • Page 15: 2005 Directed Electronics, Inc. Vista, Ca

    B B L L U U E E © 2005 Directed Electronics, Inc. Vista, CA ( ( - - ) ) L L O O C C K K ( ( + + ) ) U U N N L L O O C C K K O O U U T T P P U U T T...

  • Page 16: 2005 Directed Electronics, Inc. Vista, Ca

    ( ( - - ) ) N N E E U U T T R R A A L L S S A A F F E E T T Y Y S S W W I I T T C C H H I I N N P P U U T T © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 17: 2005 Directed Electronics, Inc. Vista, Ca

    This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the system is disarmed. The orange wire may be wired to an optional Directed Electronics 8618 starter kill relay. H H 1 1 / / 2 2 W W H H I I T T E E ( ( + + / / - - ) ) s s e e l l e e c c t t a a b b l l e e l l i i g g h h t t f f l l a a s s h h o o u u t t p p u u t t As shipped, this wire should be connected to the (+) parking light wire.

  • Page 18: 2005 Directed Electronics, Inc. Vista, Ca

    I I M M P P O O R R T T A A N N T T ! ! This output is only intended to drive a relay. It cannot be connected directly to the domelight circuit, as the output cannot support the current draw of one or more light bulbs. 1 1 8 8 button twice © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 19: 2005 Directed Electronics, Inc. Vista, Ca

    Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds will trigger the full alarm sequence. If installing an optional Directed Electronics dual stage sensor, connect both the blue and the green wires of the optional sensor to this input. This wire will report Zone 4.

  • Page 20: 2005 Directed Electronics, Inc. Vista, Ca

    When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the red/white wire will supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or other relay-driven function. 2 2 0 0 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 21: 2005 Directed Electronics, Inc. Vista, Ca

    I I M M P P O O R R T T A A N N T T ! ! Never use this wire to drive anything but a relay or a low-current input! This tran- sistorized output can only supply 200 mA, and connecting directly to a solenoid, motor, or other high-current device will cause the module to fail. © 2005 Directed Electronics, Inc. Vista, CA 2 2 1 1...

  • Page 22: 2005 Directed Electronics, Inc. Vista, Ca

    N N O O T T E E ! ! A 1-amp diode must be installed in line on the factory wire between the wait-to-start indi- cator and the ECM. (See the following diagram for details.) 2 2 2 2 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 23: 2005 Directed Electronics, Inc. Vista, Ca

    RED wire of the satellite to each feed at the switch. © 2005 Directed Electronics, Inc. Vista, CA R R e e l l a a y y f f o o r r P P o o s s i i t t i i v v e e ( ( + + ) ) D D i i s s a a r r m m W W i i r r e e...

  • Page 24: 2005 Directed Electronics, Inc. Vista, Ca

    R R E E D D / / W W H H I I T T E E ( ( + + ) ) 1 1 2 2 V V i i n n p p u u t t If additional current capacity is needed cut this wire, add a fuse adequate for the circuit to be supplied, and connect to an additional 12V source. 2 2 4 4 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 25: 2005 Directed Electronics, Inc. Vista, Ca

    (See Finding the Wires You Need section of this guide.) Once connected, you must teach the system the tach signal. (See the Internal Programming Jumpers section of this guide.) © 2005 Directed Electronics, Inc. Vista, CA 2 2 5 5...

  • Page 26: 2005 Directed Electronics, Inc. Vista, Ca

    2 2 6 6 F F i i g g u u r r e e B B © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 27: 2005 Directed Electronics, Inc. Vista, Ca

    If the vehicle is not a General Motors product or a Dodge Dakota pickup, please call Directed Electronics Technical Support for an alternative shut-down method. Do not return the vehicle to the customer until this feature is...

  • Page 28: 2005 Directed Electronics, Inc. Vista, Ca

    In addition, color variations are possible from model to model; make sure to test the circuit carefully. Please call Directed Electronics Technical Support if you need assistance in making this interface. I I M M P P O O R R T T A A N N T T ! ! Once the interface is complete, attempt to remote start the vehicle with the door closed and the key in the ignition.

  • Page 29: 2005 Directed Electronics, Inc. Vista, Ca

    2 2 9 9 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 30: 2005 Directed Electronics, Inc. Vista, Ca

    H3/2 BLUE/BLACK third ignition output to control the relay. N N O O T T E E : : When connecting to the VATS wires, it is not important which wire is cut. 3 3 0 0 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 31 This transponder system is comprised of two parts. The first part, the transceiver, circles the key switch and is activated when the key is placed in the key switch or turned to the run position. Upon activation, the trans- © 2005 Directed Electronics, Inc. Vista, CA 3 3 1 1...
  • Page 32 V V a a l l e e t t ® ® / / P P r r o o g g r r a a m m S S w w i i t t c c h h © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 33 Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while inputs longer than 0.8 seconds will trigger full alarm sequence and report Zone Two. If installing an optional Directed Electronics dual stage sensor, connect to the green wire as shown below. The diagram below eliminates the need for diodes to isolate the sensors.
  • Page 34 3 3 4 4 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 35 O O p p e e n n a a d d o o o o r r . . (The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected.) K K e e y y . . Turn the ignition to the ON position. © 2005 Directed Electronics, Inc. Vista, CA ™ ™...

  • Page 36: Standard Configuration

    LED will flash three times to confirm it is ready to receive the code from the transmitter. 3 3 6 6 W W I I R R E E C C O O L L O O R R RED/WHITE VIOLET/BLACK WHITE/BLACK © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 37 ...operates ...Disarm/Unlock/ ...operates ...Remote start ...operates ...Channel 2—trunk ...operate...3 hr Timer Mode ...operate...24 hr Timer Mode ...operate ...Short Run/Turbo ...operate...Temperature ...Control Start © 2005 Directed Electronics, Inc. Vista, CA Panic ON/Panic OFF panic off release timer 3 3 7 7...
  • Page 38 Four is now bypassed. 3 3 8 8 ...operate...Channel 4 ...operate...Channel 5 operates Temperature check operates Remote extended functions/LCD backlight operates Battery Saver Mode operate Beep/Vibrate Notification operate Time/Alarm Display operates Parking Timer © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 39 After a second, the LED will flash to indicate which feature you have accessed. For example, in Menu Two, groups of eight flashes would indicate access to the activation pulse setting (Feature 2-8). The horn will also honk eight times (if connected). © 2005 Directed Electronics, Inc. Vista, CA 3 3 9 9...
  • Page 40 ■ More than 15 seconds elapses between programming steps. One siren wail sound indicates that the Learn Routine has been exited. 4 4 0 0 will change will change the setting to the © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 41 1-11 © 2005 Directed Electronics, Inc. Vista, CA T T W W O O - - C C H H I I R R P P S S E E T T T T I I N N G G...
  • Page 42 A A c c t t i i v v a a t t i i o o n n p p u u l l s s e e c c o o u u n n t t : : 2 2 Accessory Rear defogger: latch 10 min./pulse Anti grind: OFF © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 43 1 1 - - 6 6 P P A A N N I I C C W W I I T T H H I I G G N N I I T T I I O O N N O O N N : : This feature controls whether or not the panic mode is available with the igni- tion on. In some states, there are laws prohibiting a siren sounding in a moving vehicle. This feature makes the system compliant with these regulations. © 2005 Directed Electronics, Inc. Vista, CA 4 4 3 3...
  • Page 44 Use the right and left arrows or the plus (+) and minus (-) keys on the keyboard to change the siren duration in 1 second intervals. Holding down the key will rapidly increase or decrease the setting. 4 4 4 4 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 45 2 2 - - 9 9 F F A A C C T T O O R R Y Y A A L L A A R R M M D D I I S S A A R R M M W W I I T T H H C C H H A A N N N N E E L L 2 2 : : In the default setting the factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Channel Two is pressed. © 2005 Directed Electronics, Inc. Vista, CA 4 4 5 5...
  • Page 46 "times out". This is the maximum operation period and the system may be shut down using a shutdown at any time. Using the Bitwriter, the run time can be programmed for any duration from 1-60 minutes. 4 4 6 6 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 47 If accessories such as a voice module or window module are added to the unit, it may be necessary to program this feature off. © 2005 Directed Electronics, Inc. Vista, CA buttons on the transmitter are pressed simultaneously, the...
  • Page 48 1. Open any door. 2. Press on the transmitter. 3. Press 4. Press again. You have now entered or exited Valet Mode (verify by checking your status LED). 4 4 8 8 ™ ™ © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 49 N N O O T T E E : The Warn Away® response does not report on the LED. © 2005 Directed Electronics, Inc. Vista, CA buttons the parking lights will flash 4 times and then start the vehicle and the system will remain in timer mode.
  • Page 50 S S H H U U T T D D O O W W N N M M O O D D E E Timed out Over-rev shutdown Low or no RPM Transmitter shutdown (or optional push-button) (-) Shutdown (H3/3 GRAY) or (+) Shutdown (H3/4 BROWN) (-) Neutral safety shutdown (H3/6 BLACK/WHITE) Wait-to-start timed out © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 51 Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut- down the remote start system. © 2005 Directed Electronics, Inc. Vista, CA 5 5 1 1...
  • Page 52 ■ T T h h e e V V a a l l e e t t ® ® / / P P r r o o g g r r a a m m s s w w i i t t c c h h d d o o e e s s n n ' ' t t w w o o r r k k . . Is it plugged into the correct socket? See Plug-In LED and Valet®/Program Switch section of this guide. 5 5 2 2 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 53 1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these features, the engine cranks for the preprogrammed crank time regardless of how long it takes for the vehicle to actually start. Adjust to a lower cranking time. © 2005 Directed Electronics, Inc. Vista, CA 5 5 3 3...
  • Page 54 ■ T T h h e e c c l l i i m m a a t t e e c c o o n n t t r r o o l l s s y y s s t t e e m m d d o o e e s s n n o o t t w w o o r r k k w w h h i i l l e e t t h h e e u u n n i i t t i i s s o o p p e e r r a a t t i i n n g g t t h h e e v v e e h h i i c c l l e e . . Either the wrong accessory wire is being energized or more than one ignition or accessory wire must be ener- gized in order to operate the climate control system. 5 5 4 4 © 2005 Directed Electronics, Inc. Vista, CA...
  • Page 55 5 5 5 5 © 2005 Directed Electronics, Inc. Vista, CA...

  • Page 56: Relay Sattelite Wiring

    5 5 6 6 © 2005 Directed Electronics, Inc. Vista, CA...

Table of Contents