Table of Contents
Advertisement
Setting the Channels and Clock
Preparation:
≥ Turn on the mains for the television
(and connected equipment) and select
the appropriate AV input to suit the
connections to this unit.
≥ These are the first settings you make
upon buying the unit. You don't need to
make these settings again.
1
to turn the unit on.
DVB Auto Setup starts. The unit
will search for the digital terrestrial
channels. This takes about
5 minutes.
Power Save in Standby
2
Function:
3, 4
to select "On", "On
Timer" or "Off", then
"On":
It will go into the
Power Save in
Standby mode when
the unit is in standby mode.
"On Timer": Press [3, 4, 2, 1] to set the start and stop time
and then press [OK].
≥"Power Save in Standby" is set to activate during
the setting time period.
"Off":
It is possible to start quickly from the standby
mode. (Quick Start mode)
The features of the "Power Save in Standby" function when the
unit is in standby mode are as below.
Power Save in Standby
Power consumption
1
Quick Start*
Front display
Watching the picture from the digital
satellite receiver connected to the
AV2 terminal
The unit could take over 1 minute to switch ON from standby mode with
§1
Quick start deactivated. This time could be reduced to less than 10 seconds
with Quick start activated.
When "RF OUT ( Aerial Signal )" is set to "Off" in the Setup menu (
§2
When setup has completed, the confirmation screen appears.
3
OK
TV's remote
control
DVB Auto Setup
Scan
CH 21
CH
Channel Name
27
BBC ONE Wales
27
BBC 2W
27
BBC NEWS 24
27
BBC Radio Wales
TV: 6
Radio: 4
Data: 0
Searching...
RETURN
Power Save in Standby
Power Save
From
0
:00
OK
Saves standby power consumption
by disabling Quick Start function and
CHANGE
AV2 loop-through in standby.
OK
RETURN
Activated
Deactivated
(On/On Timer)
Approx. 0.3W *
2
Approx. 11W
Deactivated
Activated
Turns off
(The clock display
disappears.)
Cannot do
(continued on the next page)
DRIVE
SELECT
68
Type
Quality
TV
9
TV
9
TV
9
Radio 9
DELETE
STOP
On
STATUS
To
6
:00
OPTION
REC
TEXT
(Off)
Tips
To cancel Auto-Setup
Press [RETURN
Stays lit
If the unit displays "No stations found!"
Press [1] to select "No" and press [OK].
Go to step 2.
Can do
After you have performed steps 2–;, turn
off the unit and confirm the cable or aerial
input is connected to the RF IN terminal.
Restart the Auto-Setup again (
Auto Setup by Signal Quality).
76)
If the clock setting menu appears or the
clock is not correct, set the clock
manually (
Restarting the Auto-Setup (
Auto Setup by Signal Quality)
To set the channel list best suited to your
region (
Region)
About the screen saver function
When this unit is not operated for
approximately 5 minutes while the screen is
being displayed, the screen saver may be
displayed.You can turn this function off
(
74, Screen Saver).
TV
VOL
CH
AV
PAGE
PROG/CHECK
CHAPTER
INPUT
SELECT
SKIP
SLOW SEARCH
PAUSE
PLAY
1.3
x
EXIT
PAUSE LIVE TV
OK
OK
RETURN
RETURN
MANUAL SKIP
-10s
+60s
REC MODE
EXT LINK
DIRECT TV REC
STTL
DISPLAY TIME SLIP
].
71, DVB
14).
71, DVB
71, DVB Auto Setup by
13
VQT2J34
Advertisement
Table of Contents
