Disc Operations; Preparing The Remote Control; Basic Play; Inserting A Disc - Panasonic SC-HC30DB Operating Instructions Manual

Control guide

Preparing the remote control

Place this side in before the other side.
■ Batteries
• Use a manganese dry battery or an alkaline dry battery.
• Insert so the poles (+ and –) match those in the remote control.
• Remove if the remote control is not going to be used for a
long period of time.
• Store in a cool and dark place.
• Do not heat or expose to flame.
• Do not leave the batteries in an automobile exposed to direct
sunlight for a long period of time with doors and windows closed.
• Mishandling of batteries in the remote control can cause
electrolyte leakage, which may cause a fire.
■ Do not:
• mix old and new batteries.
• use different types of batteries at the same time.
• take apart or short-circuit the batteries.
• attempt to recharge alkaline or manganese batteries.
• use the batteries if the coverings have been peeled off.

Disc operations

g Inserting a disc
 Press [^] to turn the unit on.
 Press [;, CD] to open the sliding door.
 With the label of the disc facing towards you, tilt the disc
into the disc tray under the sliding door.
 Place the disc onto the spindle in the centre and then
push the disc down until it clicks into place.
Click!
 Press [;, CD] to close the sliding door.
Keep fingers away from the sliding door when it is closing to
avoid possible minor injuries.
(continued)
R6/LR6, AA
Disc operations
g Removing a disc
 Press [;, CD] to open the sliding door.
 Hold the centre and the top right of the disc and pull the
top right of the disc to unlock it from the spindle.
 Tilt the disc so as not to touch the sliding door and
remove the disc.
• Damage may occur if the sliding door is forced closed.
• Be careful of CD hitting the sliding door while being removed.

Basic play

 Press [^] to turn the unit on.
 Insert the disc to be played (➡ left).
 Press [CD q/h] to start play.
Stop
Press [g].
Pause
Press [CD q/h]. Press again to resume
play.
Skip track Press [u/t] or [y/i].
Search the
Press and hold [u/t] or [y/i].
current
track (CD)
Skip album
Press [e,r].
(MP3)
CD: Press the numeric buttons to select
Direct access
play (Play starts the track.
with the track you
MP3:  Press [e,r] to select the album.
select.)
 Press [y/i] once and then the

Program play

Enables you to program up to 24 tracks.
 Press [CD q/h] and then [g].
 Press [PROGRAM].
CD:  Press the numeric buttons to select the track.
To program more tracks, continue by pressing the
numeric buttons.
 Press [OK] or [CD q/h] to start play.
MP3:  Press [e,r] to select the album.
 Press [y/i] once and then the numeric buttons
to select the track.
 Press [OK].
To program more tracks, repeat step  to .
 Press [CD q/h] to start play.
Cancel program Press [PROGRAM] in the stop mode to
mode
clear "PGM" indicator from the display.
Replay the Press [PROGRAM] in the stop mode and
program
then [CD q/h].
Check program
Press [u/t] or [y/i] when
contents
"PGM" is displayed in the stop mode.
To check while programming, press
[PROGRAM] twice after "PGM" appears
and then press [u/t] or [y/i].
Press [DEL] in the stop mode.
Delete last
programmed
track
Clear all
Press [g] in the stop mode.
programmed
"CLR ALL" is displayed. Within
tracks
5 seconds, press the button again to
clear all tracks.
• The program memory is cleared when you open the sliding door.
(continued)
numeric buttons to select the track.
9