Hilti TE7-C Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Rotary Hammer
  5. TE 7-C
  6. Operating instructions manual
Hilti TE7-C Operating Instructions Manual

Hilti TE7-C Operating Instructions Manual

Hide thumbs Also See for TE7-C:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions , Operating Instructions Manual
TE 7-C
Bedienungsanleitung
Operating instructions
de
en

Advertisement

Table of Contents
loading

Related Manuals for Hilti TE7-C

Summary of Contents for Hilti TE7-C

  • Page 1 TE 7-C Bedienungsanleitung Operating instructions...

  • Page 4: Table Of Contents

    TE 7‑C rotary hammer Operating controls and parts 1 It is essential that the operating instructions Chucks are read before the power tool is operated Function selector switch for the first time. Control switch Forward / reverse switch Always keep these operating instructions Side handle with depth gauge together with the power tool.

  • Page 5: Description

    Drilling Hammer operating instructions and always refer to it when operating material for without drilling instructions recycling. hammering making an enquiry to your Hilti representative or before use. service department. Type: Serial no.: Chiseling Chisel position Volts Amps adjustment 2. Description 2.1 Use of the product as directed...
  • Page 6 Changes or modifications to the power tool are not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.

  • Page 7: Insert Tools, Accessories

    Recommended minimum conductor cross section and max. cable lengths Conductor cross sec- 1.5 mm² 2.5 mm² 3.5 mm² 14 AWG 12 AWG tion Mains voltage 100V 50 m Mains voltage 110-120 30 m 50 m 100 ft 150 ft Mains voltage 220-240 75 m 100 m Do not use extension cords with 1.25 mm²...

  • Page 8: Technical Data

    4. Technical data NOTE The power tool is available in various voltage ratings. Please refer to the type identification plate for details of the power tool’s voltage and power rating. Power tool TE 7‑C Rated power input Rated voltage 100 V: 680 W Rated voltage 110 V: 660 W Rated power input 720 W...
  • Page 9 liquids, gases or dust. Power tools create sparks e) Do not overreach. Keep proper footing and bal- which may ignite the dust or fumes. ance at all times. This enables better control of the power tool in unexpected situations. c) Keep children and bystanders away while oper- ating a power tool.
  • Page 10 Touching rotating parts, especially Hilti Service Center. Under unfavorable circum- rotating drill bits, discs or blades, etc. may lead to stances, dampness or dust adhering to the surface injury.

  • Page 11: Before Use

    ear protection, protective gloves and breathing 5.2.5 Personal protective equipment protection while the power tool is in use. a) The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, 6. Before use 2. Release the side handle clamping band by turning the handle counterclockwise.
  • Page 12 3. Check that the sealing lip of the dust shield is 3. Slide the chuck onto the guide tube from the front clean and in good condition. Clean the dust shield and then release the sleeve. if necessary or replace it if the sealing lip is 4.

  • Page 13: Care And Maintenance

    7. Adjust the pressure applied to the power tool 7.2.4.1 Chisel position adjustment according to the material you are working on. This CAUTION will ensure the optimum rate of drilling progress. Do not work operate the power tool when the selector switch is set to “Chisel adjustment”.

  • Page 14: Troubleshooting

    8.3 Maintenance faultlessly. If necessary, the power tool should be WARNING repaired by Hilti Service. Repairs to the electrical section of the power tool may be carried out only by trained electrical specialists. 8.4 Checking the power tool after care and...

  • Page 15: Disposal

    10. Disposal Most of the materials from which Hilti tools or machines are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old tools for recycling. Please ask your Hilti customer service department or Hilti representative for further information.

  • Page 16: Ec Declaration Of Conformity

    12. EC declaration of conformity Hilti Corporation Designation: Rotary hammer Type: TE 7‑C Year of design: 2005 We declare, on our sole responsibility, that this Peter Cavada Dr. Heinz‑Joachim Schneider product complies with the following directives and Leiter Prozess‑ und Qualitätsman-...
  • Page 17 Fax: +423 / 234 29 65 www.hilti.com 000000 / A Hilti = registered trademark of Hilti Corp., Schaan W 3090 0106 10-Pos. 1 1 Printed in Liechtenstein © 2006 Right of technical and programme changes reserved S. E. & O.

Table of Contents