Notice Special Requirements - Beckett AF Manual

Genera| Specifications
Table 2 - Air Tube Combination (ATC) codes
Firing Head Static Ven- ATC Codes for usable air tube lengths
Rate plate turi ('A' in inches; See Figure 3.)
(gph) size
(rnin- (inches) 4-1/2 5 5-3/8 6-5/8 7 7-1/4 9 10-1/2 13 16
max)
0.50-0.75 F0 3-3/8U None AF44XR AF53XR AF65XR AF72XR AFg0XR AF104XR AF130XR A160XR
0.75-1.25 F3 2-3/4U None AF44XN AF53XN AF65XN AF72XN AFg0XN AF104XN AF130XN AF160XN
0.85-1.35 F4 2-3/4U None AF44WH AF53WH AF65WH AF72WH AF90WH AF104WH AF130WH AF160WH
0.85-1.65 F6 2-3/4U None AF44YB AF53YB AF65YB AF72YB AFg0YB AF104YB AF130YB AF160YB
1.10-2.00 F12 2-3/4U None AF44XO AF53XO AF65XO AF72XO AFg0XO AF104XO AF130XO AF160XO
1.65-2.50 F22 2-3/4U None AF44XP AF53XP AF56XP AF72XP AFg0XP AF104XP AF130XP AF160XP
2.50-3.00 F31 None None AF44XS AF53XS AF65XS AF72XS AF90XS AF104XS AF130XS AF160XS
0.50-1.10 L1 3-3/8U 8hole AFG50MB AFG70MB AFGg0MB
0.50-1.00 L2 2-3/4U 8hole AFG50MP AFG70MP AFGg0MP
0.75-2.75 Vl 2-3/4U 8hole AFG50MD AFG70MD AFGg0MD
0.40-0.75 F0 3-1/2U None AF44WG AF53WG AF65WG AF72WG AF90WG AF104WG AF130WG A160WG
Notice Special Requirements
• THE INSTALLATION OF A BURNER SHALL BE
IN ACCORDANCE WITH THE REGULATIONS
OF AUTHORITIES HAVING JURISDICTION.
• For recommended installation practices in the
U.S. refer to the latest edition of NFPA 31. (CSA-
B139 and CSA-B140 in Canada.
• Concealed damage -- If you discover damage to
the burner or controls during unpacking, notify the
carrier at once and file the appropriate claim.
• When contacting Beckett for service information
-- Please record the burner serial number (and
have available when calling or writing). You will
find the serial number on the silver label located
on the left rear of the burner. Refer to Figure 1.
Professional Service
Required
Incorrect installation, adjustment,
and use of this burner could result
in severe personal injury, death, or
substantial property damage from
fire, carbon monoxide poisoning, soot or explo-
sion.
Please read and understand the manual supplied with
this equipment. This equipment must be installed, ad-
justed and put into operation only by a qualified individu-
al or service agency that is:
• Licensed or certified to install and provide tech-
nical service to oil heating systems.
• Experienced with all applicable codes, standards
and ordinances.
• Responsible for the correct installation and com-
mission of this equipment.
• Skilled in the adjustment of oil burners using
combustion test instruments.
The installation must strictly comply with all applicable
codes, authorities having jurisdiction and the latest revi-
sion of the National Fire Protection Association Standard
for the installation of Oil-burning Equipment, NFPA 31
(or CSA-B139 and CSA-B140 in Canada).
Regulation by these authorities take precedence over
the general instructions provided in this installation
6104BAFG R04 Page 5