Advertisement
Table of Contents
OWNER'S
MANUAL
Thank you for choosing the
quality product and hope it will provide many hours of quality exercise to make you
feel better, look better and enjoy life to its fullest.
The Sit N Cycle is not a typical exercise bike; it is designed to be a low resistance
long duration exercise product. This is great for the office or the home for use during
activities where an individual would sit for long periods of time.
CAUTION: WEIGHT ON THIS PRODUCT SHOULD NOT EXCEED 136KG / 300LBS.
The Product May Vary Slightly From
Picture above
MADE IN TAIWAN
Sit N Cycle
. We take great pride in producing this
VERSION: 072913
Advertisement
Table of Contents
Related Manuals for Smooth Fitness Sit N Cycle
Summary of Contents for Smooth Fitness Sit N Cycle
- Page 1 The Sit N Cycle is not a typical exercise bike; it is designed to be a low resistance long duration exercise product. This is great for the office or the home for use during activities where an individual would sit for long periods of time.
- Page 2 ALL NEW MATERIALS Consisting of 100% Polyurethane Date of Manufacture 03/15/13 Model # SNC‐16 Lot # 130310...
- Page 3 “S AFETY NSTRUCTION” WARNING: To reduce the risk of serious injury, read the following safety instructions before using the item . Read all warnings posted on the equipment 2. Read this Owner's Manual and follow it carefully before using the equipment. Make sure that it is properly assembled and tightened before use 3.
-
Page 4: Parts Overview
The Sit N Cycle is not a typical exercise bike; it is Before reading further, please review the drawing designed to be a low resistance long duration exercise below and familiarize yourself with the parts that are product. -
Page 5: Hardware Identification
“H ARDWARE DENTIFICATION HART” Unpack the box in a clear area. Review the Hardware Kit List below. This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of bolts, or screws on the circles to check for the correct diameter. -
Page 6: Seat Cushion/Seat Cover Assembly
NOTE: Failure to use the Styrofoam as support for the main frame assembly may cause damage to the Sit N Cycle. c. Slide the Seat (3) into the Main Frame (1) as the drawing depicts on the right. -
Page 7: Step 5 - Pedal Assembly
” SSEMBLY NSTRUCTIONS – TEP 5 Pedal Assembly a. Note: The Right Pedal (10) has an R stamped on the end of the Step a. pedal shaft. Note: At the The Left Pedal (9) has an L stamped on the end of the end of pedal shaft are pedal shaft. -
Page 8: To Move The Item Safely
“ NSTRUCTIONS” PERATION OW TO MOVE THE ITEM SAFELY Put your fingers into the handle indentation located on the back of the Seat and gently move the item to the desired location. Make sure the floor is level while moving the item. OW TO ADJUST THE TENSION LEVEL TO INCREASE THE RESISTANCE Turn the Tension Knob (24) clockwise. -
Page 9: Parts Diagram
“P RODUCT ARTS RAWING”... - Page 10 “P IST” Item Name Q'TY Item Name Q'TY SNC-1 Main Frame SNC-29 Lock Washer (M8) SNC-2 Rear Support Frame SNC-30 Washer (8×38×2.0t) SNC-3 Seat Frame SNC-31 Washer (6×13×1.0t) SNC-4 Front Decoration Cover SNC-32 Washer (17×25×1.0t) SNC-5 Left Chain Cover SNC-33 Screw (M4×12mm) SNC-6 Right Chain Cover SNC-34 Screw (M4×25mm) SNC-7 Crank Cover...
-
Page 11: Limited Parts Warranty
Warranty period. Smooth Fitness may at its discretion choose to provide any of the stipulated parts or repair options. In the event that a part is determined to be in need of replacement, upon receipt of the defective part by Smooth Fitness, Smooth Fitness may send out the part by UPS Ground or another such carrier directly to the customer’s home at the customer’s expense. - Page 12 Customer Service Toll Free 1-888-800-1167...