Table of Contents
Advertisement
owners manual
VOLUME
Displays the track Volume. Val: 00 to 127
MD=MONO
(UPPER1 Only) Select the monophonic mode in the UPPER 1 section.
REVSEND
The value indicates the amount of Reverb effect in the track. Val: 00/15
CHOSEND
The value indicates the amount of Chorus (Modulation/Delay effect) in the track. Val: 00/15
TRANSP
Indicates the transpose setting. Val: -24/+24
DETUNE
Infl uences the overall fi ne tuning: it moves by 1/64th of a semitone. Val: -63/+63
PAN
Moves the sound of the track to the left or to the right. By setting this value to the minimum with the DIAL, keys, the
PAN mute message appears in the display; the sound is no longer heard but the effects are still active in the track.
In this case, you will only hear the effect processed sound. If the track is engaged by a Drumkit which already
features a pan setting the message PAN lock appears: in this case PAN is not active. Val: 00/31 right 00/-31 left
VOL PED
Enables or disables the Volume Pedal control on the track (the Volume Pedal is optional and must be connected
to the rear panel jack socket). Val: ON/OFF
DAMPER
Enables or disables the Damper Pedal control on the track (the Damper Pedal is optional and must be connected
to the rear panel jack socket). Val: ON/OFF
PITCH/M
Enables or disables the track for the action of the Pitch/Modulation control. Val: ON/OFF
PITCHRG
Visualize the Bender range: if the value is 00, the Pitch Bender wheel will have no effect on the track. A value
higher than 00 indicates the wheel action in semitones (e.g.: 12=1 octave). Val: ON/OFF
EDITSND
Loading a WK3 song, which can contain edited sounds, they can be listened to if the function is ON. If you wish
to listen to the original, unmodifi ed sounds, set this function to OFF. ON is the default setting
Rotate the DIAL to modify the values. You can exit any edit page at any time without losing your temporary modifi cations.
Save your modifi cations if you decide to change to a new Performance. Selecting a new Performance, or selecting the
current one again, will imply losing your data unless you save them.
The STORE PERFORMANCE function key allows you to save the panel confi guration setting to a Performance. Use
the STORE PERFORMANCE function whenever you have accomplished one of the actions described in the previous
paragraph. In this way you will photograph the desired panel setting and you will be able to recall it at all times.
Press ENTER to save (or Escape to exit the function) from the Store Performance operations.
Use the PERFORMANCE RECALL/STORE PERFORMANCE key to enter Performance mode: the arrowhead moves
automatically to the PERF menu function.
The original Performances set by the factory cannot be cancelled defi nitively, but can be restored at all times by using
the RESTORE function.
IMPORTANT:
using this function the factory-set Performances will be restored to the original memory locations, clearing the location
contents. Make sure that your programmed performances will be saved to a Floppy Disk before resetting with RESTORE. To save Performances
to disk, refer to the Disk chapter. If you modify the fi rst of the 63 available Performances, this will appear whenever WK2000 SE is turned
on. You may choose not to store your programmed Performances to disk but keep them in the machine RAM memory taking advantage of
the battery back-up. Keep in mind that in case the battery runs down all your data will be irretrievably lost.
To recap, a Performance is stored as follows:
a) Press and hold the STORE PERFORMANCE key;
b) Press ENTER to confi rm.
Select a Style with the SINGLE TOUCH PLAY function set ON, the original Performance (set by Generalmusic) is
recalled. You can modify and store it to one of the 63 programmable Performance locations available.
SAVE CHANGES TO A DIFFERENT PERFORMANCE MEMORY LOCATION (OR CREATE A NEW ONE)
If you wish to save the Performance to a new location, follow these instructions:
1
Press and hold the STORE PERFORMANCE key for a second
Rotate the DIAL to move to the location that will contain the Performance. The Performance number will be shown in
2
the display (e.g.: P 11).
3
Press ENTER. The Performance will be saved to the new location.
PERFORMANCE NAME SET
To change the Performance name, proceed as follows
1
Keep the STORE PERF. button pressed for a few seconds
2
Use the symbol located below the keyboard to write the new name.
3
Confi rm with ENTER to save the Performance
HOW TO RESTORE THE ORIGINAL PERFORMANCE SETTINGS
The INIT (refer to the [MIDI/GENERAL]) function cancels all modifi cations applied to the Performances and recalls
the original settings from the machine ROM memory.
1
Press and hold the MIDI/GENERAL button for a few seconds
2
Scroll to the INIT page with the PAGE button.
3
Rotate the DIAL to select the parts you wish to restore.
• All Memory
• Sequencer
• Performance
• Samples
4
Press the ENTER button.
Sounds&Performances
THE PERFORMANCE PARAMETERS
STORE PERFORMANCE
wk2000 se
Page17
Hide quick links:
Advertisement
Table of Contents
