Table of Contents
Advertisement
3 OPTION MENU
Use this menu to adjust the optional system parameters.
MANUAL SETUP
3 OPTION MENU
1/2
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Display settings
OPTION MENU
A)DISPLAY SET
1/2
. DIMMER;;;;;;;;;0
VIDEO CONV.;;;ON
OSD SHIFT;;;;;;0
[ ]/[ ]:Up/Down
[
[
[ ]/[ ]:Select
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: – 4 to 0
Control step: 1
• Press
l to make the front panel display dimmer.
• Press
h to make the front panel display brighter.
VIDEO CONV.
Video conversion
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO and COMPONENT
VIDEO jacks.
Choices: ON, OFF
• Select "ON" to convert composite, S-video and
component video signals interchangeably.
• Select "OFF" not to convert any signals.
Notes
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set "VIDEO CONV." to "OFF".
• When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you set "VIDEO CONV." to "ON".
MANUAL SETUP
3 OPTION MENU
2/2
. E)ZONE2 SET
F)DOCK SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
A)DISPLAY SET
OPTION MENU
A)DISPLAY SET
2/2
. OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s
FL SCROLL;;;CONT
[ ]/[ ]:Up/Down
[
[
[ ]/[ ]:Select
Customizing this unit (MANUAL SETUP)
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (upward) to +5 (downward)
Control step: 1
Initial setting: 0
• Press
l to raise the position of the OSD.
• Press
h to lower the position of the OSD.
Source feature OSD display time
OSD-SOURCE
Use this feature to set the amount of time to display the
iPod menu in the OSD after you perform a certain
operation.
Choices: ON, 10s, 30s
• Select "ON" to display the OSD continuously during
an operation.
• Select "10s" to turn off the OSD 10 seconds after you
perform a certain operation.
• Select "30s" to turn off the OSD 30 seconds after you
perform a certain operation.
Amplifier function OSD display time
OSD-AMP
Use this feature to set the amount of time to display the
status and sound field parameters information screen after
you perform a certain operation.
Choices: ON, 10s, 30s
• Select "ON" to display the OSD constantly during an
operation.
• Select "10s" to turn off the OSD 10 seconds after you
perform a certain operation.
• Select "30s" to turn off the OSD 30 seconds after you
perform a certain operation.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as a song title or a channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when "DOCK" is selected as the input source.
Choices: CONT, ONCE
• Select "CONT" to display the operation status in the
front panel display in a continuous manner.
• Select "ONCE" to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
79
En
Advertisement
Table of Contents
