Lexicon MX500 Owner's Manual page 2

IMPORTANT SAFETY INSTRUCTIONS
Safety InStructIonS
Notice For customers iF Your uNit is equipped With A poWer cord.
WArNiNG: this AppLiANce shALL Be coNNected to A mAiNs socKet
outLet With A protectiVe eArthiNG coNNectioN.
the cores in the mains lead are coloured in accordance with the following code:
GREEN and YELLOW - Earth
As colours of the cores in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
the core which is coloured green and yellow must be connected to the
•
terminal in the plug marked with the letter e, or with the earth symbol,
or coloured green, or green and yellow.
the core which is coloured blue must be connected to the terminal
•
marked N or coloured black.
the core which is coloured brown must be connected to the terminal
•
marked L or coloured red.
this equipment may require the use of a different line cord, attachment
plug, or both, depending on the available power source at installation.
if the attachment plug needs to be changed, refer servicing to qualified
service personnel who should refer to the table below. the green/yellow
wire shall be connected directly to the units chassis.
CONDUCTOR
L LIVE
N NEUTRAL
E EARTH GND
WARNING: if the ground is defeated, certain fault conditions in the unit
or in the system to which it is connected can result in full line voltage
between chassis and earth ground. severe injury or death can then result
if the chassis and earth ground are touched simultaneously.
BLUE - Neutral BROWN - Live
WIRE COLOR
Normal Alt
BROWN BLACK
BLUE WHITE
GREEN/YEL GREEN
WARNING FOR YOUR PROTECTION
PLEASE READ THE FOLLOWING:
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR
SPLASHING LIqUID AND NO ObjECT FILLED WITHI LIqUID, SUCH
AS vASES, SHALL bE PLACED ON THE APPARATUS.
CLEAN ONLY WITH A DRY CLOTH.
DO NOT bLOCK ANY OF THE vENTILATION OPENINGS. INSTALL IN
ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS,
HEAT REGISTERS, STOvES, OR OTHER APPARATUS (INCLUDING
AMPLIFIERS) THAT PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED bY THE
MANUFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN
UNUSED FOR LONG PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or third prong are provided
for your safety. If the provided plug does not fit your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched par-
ticularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Use only with the cart stand, tripod bracket, or table specified
by the manufacture, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
POWER ON/OFF SWITCH: The Power switch used in this piece of
equipment DOES NOT break the connection from the mains.
MAINS DISCONNECT: The plug shall remain readily operable.
For rack-mount or installation where plug is not accessible, an
all-pole mains switch with a contact separation of at least 3 mm
in each pole shall be incorporated into the electrical installation
of the rack or building.
FOR UNITS EqUIPPED WITH ExTERNALLY ACCESSIbLE FUSE RECEP-
TACLE: Replace fuse with same type and rating only.
MULTIPLE-INPUT vOLTAGE: This equipment may require the use
of a different line cord, attachment plug, or both, depending on
the available power source at installation. Connect this equipment
only to the power source indicated on the equipment rear panel.
To reduce the risk of fire or electric shock, refer servicing to
qualified service personnel or equivalent.