Vent Components - Vermont Castings SDVR Series Homeowner's Installation & Operating Manual

Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters

Vent Components

The following kits are available to meet the needs of most
installations. All pipe has a 7" outer diameter and includes a
4" diameter inner section. A (CG) designation indicates the
part is finished in Charcoal Gray paint. Consult your dealer
about other vent parts that may be appropriate to complete
the installation.
CFM Corporation Vent Components
Rear Vent Kit
(1) 20" Starter pipe (CG) for through wall installation
(1) Side Wall Termination
(1) Finishing Collar (CG)
(1) Firestop
(1)Zero Clearance Sleeve
(1) Wall plate (CG)
(1) Hardware Package
Min. Through the Wall Vent Kit
(1) 90-Degree Elbow (CG)
(1) 24" Straight pipe (CG)
(1) 24" - 42" Adjustable Straight Pipe
(1) Side Wall Termination
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package
(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Charcoal Gray flue pipe rings
Starter Kit for
Below-Grade Installation
(1) Snorkel Termination (7TDVSNORK)
Vertical Termination Kit, 1/12-6/12 Pitch
7TDVSKVA
(1) Combination Horizontal Offset / Roof Support
(1) Vertical Termination
(1) Storm Collar
(1) 1/12-6/12 Flashing
(1) Finishing Plate (CG)
(1) Finishing Collar (CG)
(1) Polished Brass Flue Pipe Ring
12
(1) Hardware Package
Vertical Termination Kit, 7/12-12/12 Pitch
7TDVSKVB
(1) 7/12 - 12/12 Flashing
and all of the other Vertical Termination parts.
Vertical Termination, Flat Roof
(1) Flat Flashing
and all of the other Vertical Termination parts.
7TFSRSK
Twist Lock 12" Straight Pipe (CG)
(1) 12" Non-adjustable Pipe
Twist Lock 12"-18" Straight Pipe (CG)
(1) 12" - 18" Adjustable Pipe
Twist Lock 24" Straight Pipe (CG)
(1) 24" Non-adjustable Pipe
Twist Lock 48" Straight Pipe (CG)
(1) 48" Nonadjustable Pipe
7TFSSK
Twist Lock 45-Degree Elbow (CG)
for vertical offsets
(1) 45-degree Elbow
Combination Offset/Roof Support
Attic Insulation Shield
7" Charcoal Gray Pipe Rings, (4)
7" Polished Brass Pipe Rings (4)
Use the following approved CFM/Majestic vent com-
ponents for fireplace installations vented through a
masonry chimney:
7TFSCSK
7TFSDVSKS
HEDV25
HEDV35
HEDV32T812
HEDV32T1212
HEDVT
7DVSKVF
7TFSDVP12
7TFSDVP1218
7TFSDVP24
7TFSDVP48
7TFSDVT45
7FSDRG
Transition Connector
25-foot flex connector
(two 25 foot sections)
35-foot flex connector
(two 35 foot sections)
Vent termination for 8 x 12" flue
Vent termination for 12 x 12" flue
Round termination
20007066
7DVCS
7DVAIS
7FSDRP