Changing The Input Display; Using Headphones; Using Activities To Start Easy Macros - Integra DTR-70.2 Instruction Manual

Changing the Input Display

When you connect an
must configure the input display so that
properly.
This setting can be done only from the front panel.
1
Press Tape, Game or VCR/DVR so that "TAPE",
"GAME" or "VCR/DVR" appears on the display.
2
Press and hold down Tape, Game or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select "MD", "CDR" or
"DOCK".
For the Tape input selector, the input display
changes in this order:
TAPE
For the Game input selector, the setting changes in
this order:
GAME ↔ DOCK
For the VCR/DVR input selector, the setting
changes in this order:
VCR/DVR ↔ DOCK
Note
• DOCK can be selected for the Tape, Game or VCR/DVR input
selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time

Using Headphones

Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the Phones
jack.
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the Phones jack, the
Headphone indicator, speaker/channel indicator FL and FR
lights. (The Powered Zone 2/3/4 speakers are not turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it's already set to Stereo, Mono or Direct.
• Only the Stereo, Direct and Mono listening modes can be used
with headphones.
En
28
-capable Onkyo component, you
can work
→ →
MD CDR
→
DOCK
(➔ 96).

Using Activities to Start Easy Macros

You can use Activities to execute a number of remote
control operations with a single button.
This button has the following two modes.
Easy Macro mode:
You can turn on and off the AV receiver, playback
components and TV.
Normal Macro mode:
You can assign desired operations
Note
• If you set any one of the Activities to Normal Macro mode, all
the Activities will be set to Normal Macro mode.
• To use Activities, first assign the remote control codes of the
AV components you are using
Starting Components Using Activities
Press My Movie, My TV, or My Music.
At purchase, Activities are set to Easy Macro mode
as the default setting.
The default actions are described below.
My Movie:
1. The TV turns on.
2. The playback component assigned to BD/DVD
of Remote Mode turns on.
3. The AV receiver turns on.
4. The input selector of the AV receiver is set to
BD/DVD.
5. Playback begins on the playback component
assigned to BD/DVD.
My TV:
1. The TV turns on.
2. The playback component assigned to CBL/SAT
of Remote Mode turns on.
3. The AV receiver turns on.
4. The input selector of the AV receiver is set to
CBL/SAT.
My Music:
1. The playback component assigned to TV/CD of
Remote Mode turns on.
2. The AV receiver turns on.
3. The input selector of the AV receiver is set to
TV/CD.
4. Playback begins on playback component
assigned to TV/CD.
Note
• After pressing one of the Activities, you cannot use other
Activities until the assigned actions have been com-
pleted.
• If you wish to use another of the Activities after starting,
press All Off and then press the desired Activities.
*1 Depending on the start-up time of the playback component,
the AV receiver may not be able to activate the playback com-
mand. In this case, press
(➔ 101, 103).
98).
(➔
*1
*1
on the remote controller.