Integra DTR-40.1 Instruction Manual page 144

Troubleshooting—Continued
Video
There's no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 23).
• Make sure that each video component is properly con-
nected. (pages 25 to 38)
• If your TV is connected to the HDMI OUT, select
"- - - - -" in the "HDMI Input Setup" on page 44 to
watch composite video, S-Video, and component
video sources.
• If the video source is connected to a component video
input, you must assign that input to an input selector
(page 45), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT (pages 25 and 28).
• If the video source is connected to an S-Video or com-
posite video input, your TV must be connected to the
HDMI OUT or the corresponding S-Video or compos-
ite video output (pages 25 and 28).
• If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 44), and your TV must be connected to the
HDMI OUT (page 25).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
There's no picture from a source connected to
an HDMI IN
• Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed (page 25).
• When the "Resolution" (page 43) is set to any resolu-
tion not supported by the TV, no video is output by the
HDMI OUT.
• If the message "Resolution Error" appears on the AV
receiver's display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD player.
The onscreen menus don't appear
• On Australian models, specify the TV system used in
your area in the "TV Format Setup" on page 48.
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The picture is distorted
• On Australian models, specify the TV system used in
your area in the "TV Format Setup" on page 48.
The immediate display does not appear
• The immediate display will not appear when the input
signal from the COMPONENT VIDEO IN is output to
a device connected to the COMPONENT VIDEO
MONITOR OUT.
• Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
IN is output to a device connected to the HDMI OUT.
144
Tuner
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn't
appear
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 61).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
Remote Controller
The remote controller doesn't work
• Make sure that the batteries are installed with the cor-
rect polarity (page 13).
• Install new batteries. Don't mix different types of bat-
teries, or old and new batteries (page 13).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there's no
obstruction between the remote controller and the AV
receiver's remote control sensor (page 13).
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
• Make sure you've selected the correct remote control-
ler mode (pages 14 and 133 to 139).
• When using the remote controller to control other
manufacturers' AV components, some buttons may
not work as expected.
• Make sure you've entered the correct remote control
code (page 131).
• Make sure to set the same ID on both the AV receiver
and remote controller (page 106).