Page 2
Océ-Technologies B.V. Océ-Technologies B.V. Copyright 2007, Océ-Technologies B.V. Venlo, The Netherlands. All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ. Océ-Technologies B.V. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Page 3
Trademarks Trademarks Océ, Océ FS-520, Océ Doc Exec , Océ Image Logic , Océ Scan Logic , Océ Power Logic , Océ Print Exec and Océ Remote Logic are registered trademarks of Océ-Technologies B.V. Adobe and PostScript 3 are registered trademarks of Adobe Systems Incorporated.
Page 9
Introduction Introduction Finisher FS-520 is an optional device newly added to the configuration of CS650 options. Please refer to this manual for the operation and safety information on the finisher, and keep this manual inside the user manual of the main body, readily available for reference.
Be very careful that an accident does not occur when operations such as removing paper misfeeds are performed. Finisher FS-520 Reminder Do not remove caution labels or notations. If any caution label or caution notation is soiled, please clean to make legible. If you cannot make them legible, or if the caution label or notation is damaged, please contact your service representative.
Combination size the main body and options may be different for the installation environment. Unit: mm 1619 1177 1021 1160 2419 Main body + DF-609 + LU-202 + FS-520 + PI-502 1619 1021 2142 Main body + DF-609 + LU-202 + FS-520 + PI-502 (side-view) FS-520...
Page 15
Precautions for installation and use Reminder Be sure to allow a clearance of 200 mm or more at the back of this machine for the ventilation duct. FS-520...
Opens downward to remove mishandled paper. Stacker conveyance lever Opens lower-leftward to remove mishandled paper. Staple cartridge Holds staple case to be replaced when supplying staples. Stacker unit handle Withdraws unit to allow removal of mishandled paper and replacement of staple cartridge. FS-520...
Precautions for installation and use Standard/optional equipment DF-609 OC-506 PI-502 key counter PK-512 PK-513 PF-601 main body FS-520 HT-504 LU-502 IC-408 HT-503 IC-303 IC-304 FS-520...
Precautions for installation and use Replenishing staples Inserting a new staple cartridge into Finisher FS-520 When the staple cartridge of the Finisher FS-520 becomes empty, the Staple Cartridge indicator lights in red in the option status area of the Machine Status Screen.
Page 20
Remove the empty staple case from the staple cartridge. Insert the new staple case into the staple cartridge. – Do not remove the staples remaining inside the cartridge; otherwise, the first sheet output after the replenishment will not be stapled. 2-10 FS-520...
Page 21
Precautions for installation and use Return the stacker unit to its original position. Close the Finisher door. FS-520 2-11...
Emptying waste basket of Finisher FS-520 When the waste basket of Punch kit PK-512/PK-513 installed in Finisher FS-520 becomes full, the Punch Waste Basket indicator lights in red in the option status area of the Machine Status Screen. Open the Finisher door.
Page 23
Precautions for installation and use Empty the waste basket. Return the waste basket to its original position, then close the Finisher door securely. FS-520 2-13...
Staples each set with one staple at the corner or two staples along the edge. Punch mode is available using Finisher FS-520 with Punch kit PK-512/PK-513 installed. Sheet insertion is available using Finisher FS-520 with Post inserter PI-502 installed. Paper information Weight...
Precautions for installation and use Specifications Finisher FS-520 Item Description Name FS-520 Finisher type Offset catch tray Output tray Primary (main) and secondary (sub) trays Function Straight delivery (collated, uncollated) Offset delivery (collate and offset, uncollate and offset) Staple delivery (corner staple, 2 staples) Paper Types See page 2-14 for details.
Copying operations Copying operations Using Finisher FS-520 The Finisher FS-520 has a primary (main) tray and a secondary (sub) tray, each of which has the following output modes. Output to the primary (main) tray Mode Description Non-sort Non-sort mode simply means that the offset-stacker finisher modes are not se- lected.
Combined with the output modes above, you can also choose to output face up or face down, and output front to back or back to front. Example: Make 3 copied sets Face down Face down Face up Face up collated uncollated collated uncollated FS-520...
3.1.1 Non-sort/collate/uncollate output to the primary (main) tray A machine with Finisher FS-520 installed is set to collate output to the primary (main) tray by default, regardless of whether or not to be equipped with other optional devices. Please select an output mode by following the procedures below.
Page 32
DO NOT allow any object to interfere with the operation of the tray on the left side of the finisher, as any interference may cause damage to the finisher. Be careful not to exceed the finisher tray capacity when selecting the print quantity, otherwise unexpected trouble may be caused. FS-520...
Stapled sheets will be delivered to the primary (main) tray. The Output Application icon shows the stapling position currently selected. If you want to change the stapling position, proceed to the following steps. Touch [Output Appli.] on the Copy Screen. The Output Application Screen will be displayed. FS-520...
Page 34
To release the Staple function with the current stapling position setting remained, touch [Function Off]. The Output Application Screen will be restored. Touch [OK] on the Output Application Screen. The specified output mode icon will be displayed on the Copy Screen. FS-520...
Page 35
DO NOT allow any object to interfere with the operation of the tray on the left side of the finisher, as any interference may cause damage to the finisher. Be careful not to exceed the finisher tray capacity when selecting the print quantity, otherwise unexpected trouble may be caused. FS-520...
3.1.3 Collate/uncollate output to the secondary (sub) tray A machine with Finisher FS-520 installed is set to Collate output to the primary (main) tray by default, regardless of whether or not to be equipped with other optional devices. Change the output tray and select the desired output mode by following the procedure below.
Page 37
Touch [OK] on the Output Application Screen. The specified output mode icon will be displayed on the Copy Screen. Reminder Be careful not to exceed the finisher tray capacity when selecting the print quantity, otherwise unexpected trouble may be caused. FS-520 3-11...
Copying operations 3.1.4 Punching file holes in copies (Punch) The Finisher FS-520 with Punch kit PK-512/PK-513 installed can punch file holes in output copies. Reminder Do not punch special paper type such as labels, tracing paper, etc. Otherwise, machine trouble may occur.
Page 39
If you want to change the number of punch holes and punch position, proceed to the following steps. Touch [Output Appli.] on the Copy Screen. The Output Application Screen will be displayed. Touch [Hole-Punch]. The Hole-Punch Screen will be displayed. FS-520 3-13...
Page 40
Touch [OK] on the Output Application Screen. The specified output mode icon will be displayed on the Copy Screen. Reminder Be careful not to exceed the finisher tray capacity when selecting the print quantity, otherwise unexpected trouble may be caused. 3-14 FS-520...
Copying operations Cover sheet feeding (paper inserter) The Finisher FS-520 with Paper inserter PI-502 installed can attach cover sheets to output copies. Using Insert Sheet function, cover sheets loaded in the upper and lower trays of the paper inserter will be attached as a front cover and/or back cover or insertion sheet to output copies, and also using Staple mode, a covered and stapled book can be made.
Page 42
0 Cover paper loaded in the paper inserter cannot be copied. Load cover paper into the upper and lower trays of the paper inserter. Upper tray Lower tray Use Insert Sheet function to attach covers to the output copies. 3-16 FS-520...
Copying operations Using Finisher FS-520 manually The Finisher FS-520 with Paper inserter PI-502 installed can be operated manually, using the operation panel provided on the paper inserter. Place a set of paper into the lower tray. Upper tray cannot be used.
Page 44
To use Staple in combination, turn on the desired Staple mode lamp. To select only the Punch mode, turn off all the other mode lamps. Press Start/Stop button. Do you want to stop the output operation? % Press Start/Stop button on the operation panel of paper inserter. 3-18 FS-520...
Finisher adjustment (FS-520) outlines Finisher adjustment (FS-520) outlines Use this function to make the following the fine adjustments on Finisher FS-520. For details, see CS650 User manual. Detail The target adjustment items vary depending upon the configuration of installed options.