Slab Mounting Details; Notice To Riggers; Suggested Rigging For Units Without Base Rail; Suggested Rigging For Units With Optional Base Rail - Bryant 588A Installation, Start-Up And Service Instructions Manual

Fig. 11 — Slab Mounting Details

NOTICE TO RIGGERS

Hook rigging shackles through holes in lifting brackets, as shown in De-
tail ''A.'' Lifting brackets to be centered around the unit center of gravity.
Use wooden top skid when rigging, to prevent rigging straps from dam-
aging unit.
CAUTION:
All panels must be in place when rigging.
UNIT MAX
A
588A WEIGHT
Size lb kg in.
018 332 150
024 375 170
030 384 174
036 408 185 49.4
042 447 203
048 486 220
060 525 238
UNIT
589A
024 405 184
030 408 185
036 438 199
49.4
042 463 210
048 494 224
060 525 238
Fig. 12 — Suggested Rigging for Units Without
Base Rail
B C
mm in. mm in.
24.3 618 24.85
22.4 570 24.85
22.3 565 24.85
1255 22.0 559 24.85
22.5 571 28.85
21.0 533 34.85
21.5 545 34.85
22.8 579 28.9
22.4 569 28.9
22.4 569 28.9
1255
22.8 579 34.9
21.1 536 34.9
21.5 545 34.9
Hook rigging shackles through holes in lifting brackets, as shown in De-
tail ''A.'' Lifting brackets to be centered around the unit center of gravity.
Use wood top skid when rigging, to prevent rigging straps from damag-
ing unit. Remove 4 screws to slide wood support through rectangular
hole in rail.
CAUTION:
UNIT MAX
588A WEIGHT
Size lb
018 320
024 363
030 380
036 396
042 435
048 474
060 513
UNIT
589A
024 393
030 396
036 426
042 451
048 482
060 513
Fig. 13 — Suggested Rigging for Units With
A. Units Without Base Rail
If accessory rigging brackets are to be used for rigging, in-
stall them as follows:
WARNING: Secure screws and paint protectors sol-
idly against unit basepan to hold lifting brackets in
position.
Never use lifting brackets when the temperature is be-
low −10 F.
mm
Never exceed 200 lbs per bracket of lifting force.
631
631
Never use lifting brackets for lifting other models of air-
631
conditioning units.
631
733
Lifting point should be directly over the unit center of
885
gravity.
885
1. Position brackets as close to the corners of unit as pos-
733
sible. Be sure brackets are well outside of center of grav-
733
ity. (See Fig. 2, 4, 6, 8, and 12.).
733
885
2. Position paint protectors and foam strips between screws
885
and painted surface of unit. Tighten screws until they
885
make contact with the paint protectors.
3. Secure device or hook of sufficient strength to hole in
bracket as shown in detail ''A'' of Fig. 12.
4. If wood top is available, use it for a spreader bar to pre-
vent straps from damaging unit. If wood top is not avail-
able, use spreader bars of sufficient length.
—12—
NOTICE TO RIGGERS
All panels must be in place when rigging.
A B
kg in. mm in.
145 24.4
165 22.6
172 22.5
180 49.4 1255 22.2
197 22.6
215 21.2
233 21.6
178 22.9
180 22.6
193 22.5
49.4 1255
205 22.9
219 21.3
233 21.6
Optional Base Rail
C
mm in. mm
619 28.2 715
574 28.2 715
571 28.2 715
563 28.2 715
574 32.2 816
538 38.2 969
549 38.2 969
582 32.2 816
574 32.2 816
571 32.2 816
582 38.2 969
540 38.2 969
549 38.2 969