Error Code List (Error Display In Panel) - JUKI IP-110 Type F Instruction Manual

22-1. Error code list (Error display in panel)

There are the follow�g error codes � ths devce. These error codes �terlock (or lmt fu�cto�) a�d �form
the problem so that the problem s �ot e�larged whe� a�y problem s dscovered. Whe� you request our
service, please confirm the error codes.
No. Descrpto� of error detected
− Meda cover ope�
E000 Executo� of data �talzato�
(Ths s �ot the error.)
E003 Dsco��ecto� of
sy�chro�zer co��ector
E004 Sy�chro�zer lower posto�
se�sor falure
E005 Sy�chro�zer upper posto�
se�sor falure
E00 Overload of motor
E0 Meda s �ot �serted.
E02 Read error
E03 Wrte error
E04 Wrte protect
E05 Format error
E06 Exter�al meda capacty over
E09 Fle sze over
E032 Fle �tercha�geablty error
E00 Slp of belt
E0 Dsco��ecto� of motor
output co��ector
E02 Overload of motor at the tme
of thread trmm�g moto�
E220 Grease-up war��g
E22 Grease-up error
E302 Fall detecto� swtch falure
(Whe� the safety swtch
works)
Cause of occurre�ce expected
• Cover of the slot of meda s ope�.
• Whe� the mach�e head s cha�ged.
• Whe� the �talzato� operato� s executed
• Whe� posto� detecto� sg�al s �ot �put
from the sew�g mach�e head sy�chro�zer.
• Whe� the sy�chro�zer has broke�.
• Belt s loose.
• Mach�e head s �ot proper.
• Motor pulley s �ot proper.
• Whe� the mach�e head s locked.
• Whe� sew�g extra-heavy materal beyo�d
the guara�tee of the mach�e head.
• Whe� the motor does �ot ru�.
• Motor or drver s broke�.
• Meda s �ot �serted.
• Data of meda ca��ot be read.
• Data of meda ca��ot be wrtte�.
• Meda s � the state of wrt�g prohbto�.
• Formatt�g ca��ot be performed.
• Capacty of meda s short.
• Fle s too large.
• There is no interchangeability of file.
• Whe� the mach�e head s locked.
• Belt s loose.
• Dsco��ecto� of motor co��ector
• Same as E00
• Whe� the predeterm�ed �umber of sttches
has bee� reached.
• Whe� the predeterm�ed �umber of sttches
has bee� reached a�d the sew�g s �ot
possble.
• Whe� fall detecto� swtch s �put � the
state that the power s tur�ed ON.
- 39 -
�tems to be checked
• Close the cover.
• Check the sy�chro�zer co��ector (CN33)
for loose co��ecto� a�d dsco��ecto�.
• Check whether the sy�chro�zer cord has
broke� s�ce the cord s caught � the
mach�e head.
• Check the belt te�so�.
• Check the sett�g of the mach�e head.
• Check the sett�g of the motor pulley.
• Check whether the thread has bee�
e�ta�gled � the motor pulley.
• Check the motor output co��ector (4P) for
loose co��ecto� a�d dsco��ecto�.
• Check whether there s a�y holdup whe�
tur��g the motor by ha�d.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Tur� the power OFF a�d check the meda.
• Check whether there s a�y holdup whe�
tur��g the motor by ha�d.
• Check the belt te�so�.
• Check the motor output co��ector for loose
co��ecto� a�d dsco��ecto�.
• Same as E00
• Replenish the specified places with grease
a�d reset.
(For the detals, refer to the data of the
mach�e head.)
• Replenish the specified places with grease
a�d reset.
(For the detals, refer to the data of the
mach�e head.)
• Check whether the mach�e head s tlted
wthout tur��g OFF the power swtch (sew�g
mach�e operato� s prohbted for safety
sake).
• Check whether the fall detecto� swtch cord
s caught � the sew�g mach�e or the lke.
• Check whether the fall detecto� swtch lever
s caught � someth�g.
• Check whether the co�tact of the tlt
detecto� swtch lever wth the mach�e table
s �adequate. (The table has a de�t or the
mou�t�g locato� of the bed strut s too far)