Simplified Function Setting - JUKI IP-110 Type F Instruction Manual

14. SIMPLIFIED FuNctIoN SEttING

warNING :
If the solenoid is used under the air drive mode, the solenoid can burn out. Be sure to carefully avoid
the wrong setting of the presser foot lifting device specification.
Function setting items can be simplified in part.
[Simplified function setting screen]
2
3
* Wper fu�cto� (WP): Swtches 2 a�d 3
Ths fu�cto� actvates the wper.
oFF : : The wper does �ot operate after thread trmm�g. The wper does �ot operate after thread trmm�g. The wper does �ot operate after thread trmm�g.
o� : : The wper operates after thread trmm�g (sta�dard sett�g at the tme of delvery) The wper operates after thread trmm�g (sta�dard sett�g at the tme of delvery) The wper operates after thread trmm�g (sta�dard sett�g at the tme of delvery)
* Auto-lfter (FL): Swtches 4 a�d 5
Ths fu�cto� actvates the auto-lfter fu�cto� whe� the presser foot lft�g devce (AK) s �stalled o� the
sew�g mach�e.
For the presser foot lifting device specifications, solenoid drive mode (+33 V) or air drive mode (+24 V)
ca� be selected.
The drve source voltage (CN3) s cha�ged over betwee� +33 V a�d + 24 V accord�g to the drve
mode specification selection.
oFF : : Auto-lfter does �ot operate. (sta�dard sett�g at the tme of delvery)
(The presser foot does �ot automatcally go up whe� the program sew�g s completed.)
o� S : : Auto-lfter operates. (Sole�od drve mode [+33 V])
o� A : : Auto-lfter operates. (Ar drve mode [+24 V])
* Needle posto� cha�geover fu�cto� for the tme whe� the sew�g mach�e stops (�P): Swtches 6 a�d 7
The �eedle posto� at the tme whe� the sew�g mach�e stops ca� be cha�ged over.
Lo : : Lower stop posto� (sta�dard sett�g at the tme of delvery) Lower stop posto� (sta�dard sett�g at the tme of delvery) Lower stop posto� (sta�dard sett�g at the tme of delvery)
UP : : Upper stop posto� Upper stop posto� Upper stop posto�
3) O�ce you have completed the sett�g, press swtch 8 . The scree� s cha�ged over to the power swtch
OFF notification screen.
[Power switch OFF notification screen]
If "on" (auto-lifter operates) is selected without the auto-lifter installed, the machine startup is mo-
mentarily delayed at the beginning of sewing. In addition, the one-touch type reverse feed (touch-back)
switch may be disabled. to avoid these troubles, be sure to select "oFF" (auto-lifter does not oper-
ate) when the auto-lifter device is not installed.
4 6
5 7 8 1
) Keep�g thread trmm�g prohbt�g swtch 1
held pressed, tur� the power ON. The�, the
screen is changed over to the simplified func-
to� sett�g scree�. The detals dsplayed o� the
scree� represe�t the curre�t sett�gs.
2) Fu�cto� tems ca� be cha�ged by press�g
swtches 2 a�d 3 , 4 a�d 5 or 6 a�d 7 .
4) Tur� OFF the power swtch to ext from the sm-
plified function setting.
- 22 -