Maintenance - Thermador Professional PRO-GRANDT PRD30 Care And Use Manual

Professional pro-grand dual fuel ranges
Hide thumbs Also See for Professional PRO-GRANDT PRD30:
Table of Contents

Advertisement

Available languages

Available languages

Do-It-Yourself Maintenance
Oven Light Bulb Replacement
CAUTION:
Before replacing the light bulb, be certain the
Oven Light Switch is in the off position. Let bulb
and cover cool completely before touching. If the
light bulb glass comes loose from the base, turn
the power to the oven OFF at the circuit breaker
panel before attempting to remove the bulb base
from the socket.
Replace only with a recommended light bulb designed for
appliance oven use. DO NOT USE a standard household
light bulb in any oven. Call Thermador Customer Care
Center at 800-735-4328 or your nearest Thermador dealer
to determine the proper replacement bulb for your range.
You will need to know your range's serial number.
To Replace the Light Bulb:
1.
Make sure that oven light switch is in the OFF position.
2.
Remove the light cover--
With a flat-blade screwdriver in one hand, use the
screwdriver as a small wedge to gently pry apart the
glass cover from the metal housing and hold the glass
in the other hand as it releases from the housing.
3.
Remove the burned-out bulb. Replace it with a
recommended appliance light bulb only. Do not touch
,
bulb with fingers. Follow the bulb manufacturer's
instructions.
Replace the glass cover by aligning it with the housing
and pressing on both ends of the glass, with equal
force, until the cover snaps into position. Avoid
applying excessive force on the glass.
Power Failure
In the event of a power failure, only the standard burners
can be lighted manually. It is necessary to light each
standard burner individually.
If the range's cooktop is being used when the power failure
occurs, turn all of the burner control knobs to the OFF
position. The standard burners can be lighted by holding a
match at the ports and turning the control knob to the 141
position. Wait until the flame is burning all the way around
the burner cap before adjusting the flame to the desired
height.
The two ExtraLow ® burners on the left side cannot be used
during a power failure. Be sure to turn them OFF if a power
failure occurs because they will not turn back on until the
control knobs are turned OFF and then turned back on
again. See "WHAT TO DO IF YOU SMELL GAS" on
page 1.
If you have low gas pressure, contact your gas company.
Intermittent
or Constant
Igniter Sparking
Intermittent or constant sparking of the sealed gas surface burners can result from a number of preventable conditions.
Eliminate these conditions as indicated in the following chart.
!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i!i!i!i!i!i
!i!i !i !i!i!
i_!!_
ii_!i,i_
_!_i_
_,ii_!!
_!i_!_i_!_!_!
_! i_!i_!i_
!i_!i_!i
_!i_!
i_! i_!i_!i_
!i_!i_!i
_!i_!
i_! i_!i_!i_
!i_!i_!i
_!i_!
i_!i_!i_!i_
!i_!i_!i
_!i_!
i_! i_!i_!i_
!i_!i_!i
_!i_!
i_! i_!i_!i_
!i_!i_!i
_!i_!
i_! i_!i_!i_
!i_!i_!i
_!i_!
i_! ¸ i i i ii iii ii iiii iiii iii iii ii iiii ii ii iii iii ii iiii ii iiiii iii iiiiii
ii iiiii iii ii iiii iiii iii iii ii iiii ii ii iii iii ii iiii ii ii iiiiii
iiiiii
ii iiiii iii ii iiii iiii iii iii ii iiii ii ii iii iii ii iiii ii ii iii iii iiiiii
ii iiiii iii ii iiii iiiiii'i
i'i_i_i!_i!_
i_!i _!i _!i_!
i_!i_!i_
!i_!i_!i
_!i_!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_!i_!i_
!i_!i_!i
_!i_!i_!
i_!i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_!i_!i
_!i_!i_!
i_!i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_ !i_!i
_!i _!i_!
i_! i_!i_
!i_!i_i_
_i_
_ iii ...........................................................
iiii iiiiiii
iii ii iiii ii iiiii iii ii iiii ii iiiii iii iiiiii
ii iiiii iii ii iiii iiiiiii
iii ii iiii ii iiiii iii ii iiii ii iiiii iii iiiiii
ii iiiii iii iiiiii
iiiiiii
iii ii iiii ii iiiii iii ii iiii ii iiiii iii ii iiii ii iiiii iii iiiiii
iiiiiii
iii ii iiii ii iiiii ii iii' ii'ii_i!
!_i_ !_i' i_i _!_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i__i_i_i
_i_i_
i_i_
_i__i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i__i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i__i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_i_
_i_
_i_i_i
_i_i_
i_!i_
!i_ ii!i !i
Intermittent sparking
Ceramic igniter is wet or dirty.
Burner ports are clogged.
Carefully dry or clean igniter.
Clean ports on burner cap with a wire, a
needle or straightened paper clip.
More than four clicks of
Improper fit of burner cap onto
Align burner cap properly on burner base.
igniter before lighting
burner base.
Constant Sparking
Range is not properly grounded.
Electrical power supply is incorrectly
polarized.
Refer to Installation Instructions. Have a
qualified electrician ground the range
properly.
Refer to Installation Instructions.
Have a qualified electrician ground the
range properly.
English 37

Advertisement

Table of Contents
loading

Table of Contents