Table of Contents
Advertisement
REMOTE
CONTROL
OPERATING
INSTRUCTIONS
1)
Power
On and
Off - Press the POWER
(110) button once to manually
turn the unit on. Press the Power
button once more to turn the unit off. When you press the POWER
button the upper right square
on the
remote
control
LCD Display
will light up. When in Air Conditioner,
Heating,
and Auto mode, the selected
temperature
will appear
on the remote
control
display.
When the unit is in Fan mode and Dehumidifier
mode you will see the "- -" icon instead
of the set temperature.
This shows that temperature
selection
is not
available
when the unit is in Fan or Dehumidifier
mode.
2)
Mode
Selection
- Press the MODE
Button
repeatedly
to cycle between
the different
modes:
Auto, Air
Conditioner,
Dehumidifier,
Fan only, and Heater mode. The upper left square on the Remote
control
dis-
play will light up showing
which mode is selected.
In Air Conditioner
mode the display will show
"COOLING",
in Heating
mode the display will show "HEAT",
in Dehumidifier
mode the display
will
show "DRY",
in Fan mode the display
will show "FAN",
and in Auto mode the display will show
"AUTO".
3)
Fan Speed
- Press the FAN speed button to cycle through
low, medium,
and high fan speeds.
The dis-
play on the remote control
will show LOW, MED, & HIGH
under the "SPEED"
label on the remote
con-
trol LCD display.
There is an additional
auto speed setting that is enabled
in only heating
and cooling
modes.
This speed is next setting after low when pressing
the FAN speed button on the remote
control.
The speeds will cycle through
in this order: High, Medium,
Low, Auto.
Each change
in speed will be as-
sociated
with a "beep"
sound from the unit. The remote
control
will not display
"AUTO"
under the speed
label. Once Auto fan speed is selected
the unit will beep and there wilt not be a fan speed displayed
on the
remote
control.
4)
Temperature
Settinfl
- When the unit is in Air Conditioner
or Heating
mode you can select your desired
temperature.
Press the •
or • to select your desired
temperature
setting.
The temperature
on the LCD dis-
play on the remote control
will increase
or decrease
accordingly.
Pressing
the •and
•
buttons
simultane-
ously will change the temperature
select between
°F and °C.
5)
SWING
- To turn on the exclusive
WAVEFLO®
oscillation,
press the SWING
button on the remote
control.
Once you press SWING,
the louvers
on the unit will oscillate
up and down and back and forth.
The bottom
left square
of the remote
control
display will show the "<-----_' icon when WAVEFLO®
oscillation
(SWING)
is selected.
6)
TIMER - To program
the timer,
first press the T-ON
button.
Once T-ON
is pressed
the auto-on
timer will
blink in the bottom
right rectangle
of the remote control
display.
Press the MIN and HOUR
buttons
to
change
the clock to the desired
time for the unit to automatically
turn on. The minutes
will increase
by 10
with each press of the MIN
button and the hours will increase
by 1 with each press of the HOUR
button.
Press the T-OFF
button
and the remote
control
display will flash the desired
auto-off
timer.
Press the MIN
and HOUR
buttons
to change
the clock to the desired
time for the unit to automatically
turn off. The timer
is set when the auto-offtime
stops flashing
and the words "ON" and "OFF"
are displayed
next to the time.
7)
CLOCK-
To set the clock on the remote control,
hold down either the MIN or HOUR
button until the
displayed
time flashes
on the remote
control
display.
Change
the minutes
by pressing
the MIN button and
change
the hours by pressing
the HOUR
button.
12
Hide quick links:
Advertisement
Table of Contents
