Pioneer SD-P4053 Operating Instructions Manual page 9

Projection monitor receiver
Table of Contents

Advertisement

FRONT PANEL FACILITIES
([
POWER SWITCH
AND INDICATOR
Press once to turn on the Dower Press again to turn the power off
The POWER indicator lights up when the power is on This unit Jsequip.
ped with an Auto OFF circuit. 30 minutes after the input s_gnat ceases
Io be supplied (for example, the TV channel betng received stops broad-
casting), the power automatically turns off
_2
INPUT SELECTOR
BUTTON
Press to select your program source: TV, LD player. VIDEO 1 VIDEO
2 or VIDEO 3. Each press of the button changes the selection to the nexl
source.
_.,
CHANNEL
BUTTONS
Press plus (+) or minus (--) to tune to a higher or lower channel. Only
those channels in tuner preset can be tuned in by this method. For de-
tails, see page 27.
_'
VOLUME BUTTONS
Press the plus (+) or minus (-)
buhon to raise or lower the volume
(_)
STOIAV MEM (Standard/AV
Memory)
BUTTON
Press to switch between the standard (STD) picture/sound
settings and
the AV MEMORY 1 and AV MEMORY 2 settings which have been input
with the MENU SET button.
/
NOTE:
eOn rare occasions,
an electrical
d_scharge
may occur _ns_de the CRT
It makes
a short, sharp peg 3no results
n a t or 2 s_ond
power
t_ lure
Tne power
w_t! return
automabcai/y
You need
not
worry
about
the
U_scharge:
/t is not a detect
and
wslJo_sappear
with regular
use
The
P_cture._n.Picture
tuPot/on
will be cancelled
automat,_ally
ff a oo_er
_a,lure
occurs
_hen
this tunct;on
_s engaged
,6
DPO(Dynamic
Picture Optimizer) BUTTON
Press to turn DPO on or off as desired. When DPO is on, it automati-
cally adjusts the picture to compensate
for room illumination. For de-
tails, see page 36.
NOTE:
eWhen the DPO button ,s pressed and held for more than 2 seconds.
the hnear white system will be turned off and 'LINE4R
WHITE OFF"
w_llapoear on the screen. The linear white system will resume opera-
#on approx
4 seconds alter the DPO button _sreleased
.,_j
DIGITAL P IN P (Picture-in-Picture)
BUTTONS
ON/OFF:
Press to turn the Picture-in-Picture
function on and off.
INPUT:
Press to select the sub screen program and one sub-pic-
ture mode will be selected.
eFor details on the Picture-in-Picture
function,
refer to the remote
control unit's operating instructions.
NOTES:
elf only the _
LD and VIDEO jacks of the LD player and/or
VCR are connected to the PrOlecbon Momtor, the P,cture-_n.PIctufe func-
tion w_ll not operate when these buttons are pressed
• When the P IN P button _spressed and held for more than 2 seconds.
The Projection Monffor will go _nto ,ts demonstrabon mode
"P IN P
DEMONSTRATION"
wpJI a ppear on the screen while P_cture-_n-P_cture
demonstration
mode _s engaged.
• 7_e P_cutre-n.P_cture demonstratton mode will be cancelled ff any other
opera#on key or operatton butlon _S pressed, and the Prcjectzon Monitor
will enter the selected operatton mode
_." PRESET MENU BUTTONS
These buttons are used to perform the following functions: color con-
vergence tuner presetting TV-CATV selection, relabel!ng input displays.
system mode sett=ng and AV memory storage
For details, refer to the
description of each'function.
ON/OFF:
Press to turn the Menu (functions above) on and off. When
the button =s pressed on. the function
names CONVERGENCE.
AV
MEMORY,
DPO BASE, INPUT LABEL,
TV-CATV MODE, TUNER
PRESET and SYSTEM MODE are displayed on the screen
SELECT/ADJUST
(+/-):
Press to select the desired function
The
selected function is displayed
in red.
SET: Press to activate the selected function
NOTE:
• Refer to page 37. ff you w_sh to use the SYSTEM MODE function
,_
INPUT JACKS (VIDEO-3)
These front panel jacks are convenient for connecting portable VCR, a
video camera recorder or other temporary
video source to the moni-
tor. When Ihe audio signal of the source to be connected is monaural,
connect the L (MONO) jack.
Use the S-VIDEO jack when connecting
an S-VHS or ED Beta VCR.
or an LD player which has an S-output jack.
:_0 REMOTE
CONTROL
SENSOR
Tn_ssensor p:ckS up ntrared s_gnals Iror'n the remote control u_I
0J_ OPO SENSOR
This sensor detects
ambient lighting for the DPO (Dynamic Picture
Optimizer) circuit which optimizes the TV picture accordingly.
9

Advertisement

Table of Contents
loading

Table of Contents