Operation; Using The On-Screen Menus - Runco VideoXtreme VX-11d Installation & Operation Manual

To display the Main Menu, press the MENU button on the remote control (Figure 2-5) or
DHD Controller front panel (Figure 2-3).
To select a menu item, use the
front panel to highlight it. Then, to confirm your selection, press ENTER on the remote
control or DHD Controller front panel.
The DHD Controller OSD menus are arranged hierarchically, as shown in Figure 4-1.
Depending on the selected input source and signal characteristics, some menu options
may not be available.
Composite 1
Composite 2
Composite 3
Component
HD 1
Input Source
HD 2
SCART
HDMI 1
HDMI 2
HDMI 3
HDMI 4
16:9
4:3
Letterbox
Aspect Ratio
VirtualWide
Cinema
Virtual Cinema
Native
Screen
Screen 1 / Screen 2
Brightness
Contrast
Color
Picture
Tint
Sharpness
Noise Filter
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
Input Position
(Zoom/Crop)
Phase
(RGB/Component/SCART signals
only)
Tracking
(RGB/Component/SCART signals
only)
Recall ISF Night or ISF Day
Memory
Recall/Save Custom 1 or Custom 2
Presets
Reset Custom 1 and Custom 2 to
Factory Default
Off, 30 Minutes, 60 Minutes, 90
Sleep Timer
Minutes, 2 Hours or 4 Hours
Signal
System
Information
Network
Field Service
Manufacturing
Figure 4-1. VX-11d OSD Menu Structure
Runco VX-11d Installation/Operation Manual
and buttons on the remote control or DHD Controller
Calibration
Note: Default settings appear in bold type.
Gain
Offset
Gamma
Display Color -
Common Settings
Color Temp
Color Gamut
PCE
Lamp
Display Color -
Projector Settings
ConstantContrast
Brightness
Contrast
Input Image Color
Tint
Sharpness
Gain
Offset
Input Color
Chroma Delay
Noise Filter
Save ISF Night
Back / Confirm
Save ISF Day
Memory Preset
Copy/Paste
Aspect Ratio
Left/Right
Up/Down
Width
Output Shift
Height
Screen Masking
Corner Alignment
Image Alignment
Midpoint Alignment
Owner Name
ISF Calibrated
Splash Configure ISF Other
Splash Timer
Splash Enable
OSD Position Hor. / Ver.
51

4. Operation

4.1
Using the On-Screen
Menus
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35, 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Simple
(5500K, 6500K, 7500K or 9300K)
Auto, REC709, SMPTE-C, EBU, Native or PCE
Red x, y / Green x, y / Blue x, y / White x, y
Yellow x, y / Cyan x, y / Magenta x, y
Power (230W or 260W)
On / Off
-50, -49 ... 0 ... 49, 50
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
0, 1, 2 ... 7
(Composite inputs only)
0, 1, 2 ... 63
Copy Settings
Paste Settings
Copy Settings
Paste Settings
-50, -49 ... 0 ... 49, 50
-50, -49, 48 ... 0
0, 1, 2 ... 100
(Top / Bottom / Left / Right / Test Pattern Enable)
Top Left / Top Right / Bottom Left / Bottom Right /
Test Pattern Enable
Center / Top Middle / Left Middle / Right Middle /
Bottom Middle / Test Pattern Enable
5, 6, 7 ... 15 ... 59, 60
On/Off
0, 1, 2 ... 100