Tool Specifications - Bostitch LHF97125 Operation And Maintenance Manual

TOOL SPECIFICATIONS
All screws and nuts are metric.
MODEL LENGTH HEIGHT WIDTH WEIGHT
BT125 10-1/8" (257.1mm) 8-1/4" (2096 mm) 2-5/16" (59.7 mrn) 1.9 Ib (1.0 kg)
BT200 10-1/8" (257.1 mm) 9-5/8" (244.0 mm) 2-5/16" (59.7 mrn) 2.1 Ib (1.0 kg)
SX150 10-1/8" (257.1mm) 9-5/8" (244.0 mm) 2-5/16" (59.7 mrn) 2.3 Ib (1.0 kg)
SL150 10-1/8" (257.1mm) 9-5/8" (244.0 mm) 2-5/16" (59.7 mrn) 2.4 Ib (1.1 kg)
SX150-BHF 10-1/8" (257.1mm) 9-5/8" (244.0 mm) 3-1/4" (82.6 mrn) 3.2 Ib (1.4 kg)
LHF97125 10-1/8" (257.1mm) 8-1/4" (209.6 mm) 3-1/4" (82.6 mrn) 2.5 Ib (1.1 kg)
S97125 10-1/8" (257.1 mm) 8-1/4" (209.6 mm) 2-5/16" (59.7 mrn) 2.1 Ib (1.0 kg)
US056 10-1/8" (257.1mm) 7-5/8" (178.0 mm) 2-5/16" (59.7 mrn) 2.2 Ib (1.0 kg)
SL1250C 10-1/8" (257.1mm) 8-1/2" (204.7 mm) 2-5/16" (59.7 mrn) 2.3 Ib (1.0 kg)
FASTENER SPECIFICATIONS:
TOOL BRAD/STAPLE CROWN WIRE SIZE FASTENER RANGE
MODEL SERIES WIDTH
BT125 BT1300 .050"X 040" (1.27rnmX1.04rnm) 5/8"- 1-1/4"(15mrn-32rnrn)
BT200 BT1300 .050"X.040" (1.27mmX1.04mm) 5/8"-2" (15mrn-38mm)
SL150 SL8035 5/16"(8.0mm) .050"X0.035" (1.3X0.89mm) 1/2"-1-1/2"(12mm-38mm)
SX150 SX5035 7/32"(5.6mm) .050"X0.035" (1.3X0.89mm) 1/2"-1-1/2"(12mm-38mm)
SX150-BHF SX5035 7/32"(5.6mm) .050"X0.035" (1.3X0.89mm) 1/2"-1-1/2"(12mm-38mm)
LHF97125 SB97 3/16"(4.7mm) .028"X0.035" (0.7X0.89mm) 1/2"- 1-3/8"(12mm-35mm)
$97125 SB97 3/16"(4.7mm) .028"X0.035" (0.7X0.89mm) 1/2"- 1-3/8"(12mm-35mm)
USO56 STCR5019 7/16"(11.1 mm) .050"X0.019" (1.3X0.48mm) 1/4"-9/16"(6mm-14mm)
SL125OC SL8035 5/16" (8.0mm) .050"x.035" (1.3X0.89mm) 1/2"-1-1/2" (12mm-38mm)
TOOL AIR FITTING:
This tool uses a free-flow connector plug, 1/4" N.P.T. male plug. The inside diameter should be .200" (5mm) or
larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply.
OPERATING PRESSURE:
70 to 120 p.s.i.g. (4.8 to 8.3 kg/cm_). Select the operating pressure within this range for best fastener
performance. DO NOT EXCEED THE RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION:
The LHF97125, BT125, USO56 and SL125OC require 2.8 cubic feet per minute (.08 cubic meters) the BT200,
SX150, SX150-BHF and SL150 require 3.1 cubic feet per minute (.09 cubic meters) of free air to operate at
the rate of 100 nails per minute, at 80 p.s.i. (5.6 kg/cm_). Take the actual rate at which the tool will be run to
determine the amount of air required. For instance, if your fastener usage averages 50 nails per minute, you
need 50% of the tool's c.f.m, which is required to operate the tool at 100 nails per minute.
-4-