Troubleshooting
Most p_blems
you encounter
with
your
TV you can _
by consulting
ther_ubleshooting
list.
Note: If you prefer, _ve can provideyou with the name of on Au thorized ServiceRepresentative who will visit your home for o fee
to hlstall your electronic entertainment system end to instruct you in it3 operation Fordetails about this service,call 1 888
206-3359 or visit rco com
TV Problems
1V won't turn on
•
Cheek the wall receptacle [or extension cord) to make sure it is "llve" by plugging in somethlng else.
•
Pressthe POWERbutton on the front of the W. If the IV turns on, check the remote control solutions.
•
[he front panel controls may be locked Idlsabled). Use the remote control to unlock the front panel controls by sele_tlng
the Front P_n¢l Block in the I_rental Controls menu and choosing Unblock.
Controls
don*t work
•
if you're using the remote control, press the TV button first to make sure the remote is in _iVmode.
•
[he front panel controls may be locked Idlsabled). Use the remote control to unlock the front panel controls by sele_tlng
the Front P_nel Block in the Parental Controls menu and choosing Unblock.
•
Unplug the IV for two mlnutes and then plug it back in. Turn the IV on and try agaln.
_/turns
off while playing
•
Scheduled Off fun_tlon may have been activated. Oo to page 14 for instructions.
•
Electronic protection cireult may have been activated due to a power surge. Wait 30 seconds and turn the fV On again, if
this happens frequently, the voltage in your house may be abnormally high or low.
Blank screen
•
Make sure the component connected to the TV is turned on.
When I turn on the TV an icon is moving on the screen
•
Make sure you have removed the Demo Pin from the G=UNKjack On the back of your iV.
No sound, picture okay
•
Maybe sound is muted. Pressthe volume up button to restore sound.
•
Maybe speakers are turned off. Che_ktheAudloOutputandSpeakers_ontrolpanellntheAudiomenu.
•
ff using S=VIDEOcables to connect a component, remember to also connect the componenCs left and rlgbt Audio Output
Jacks to the IVs R-AUDIO-L INPU_t Jacks.
Can't select certain
channel
•
Channel may be blocked or not approved in the Parental Controls menu.
•
if uslng a VCR, make sure the W/VCR button on the VCRis in the correct mode (press the IV/VCR button on your VCR).
Noisy stereo
reception
•
_he station might be weak. Pressthe SOUND button on your remote to change from stereo to mono.
NO picture,
no sound but 13/is on
•
Maybethe_ab1e/airsettingissett_th_wmngp_siti_n_Se_e_t_igna_fypefr_mtheChanne_m_nu_
•
The channel might be empty - change channels.
•
ff you're watchlng your VCRand it's connected with eoaxlal cable to the CABLE/ANT£NNAjack, tune the fV to channel 3
or 4 (whichever channel is selected on the 3/4 switch on the back of your VCRI. Also check to make sum the W/VCR
button on the VCR is in the correct mode (pressthe TM/VCRbutton on your VCR).
•
ff you're twing to watch content from a component that's connected to the IV (llke a DVDplayer or VCR),press the
WHO,INPUT button on the remote control until the content appears.
Sound okay, picture
poor
•
Check antenna eonneetlons. Make sure all of the cables are firmly connected to the jacks.
•
[nl adjusting sharpness funetlon to improve weak signals.
Black box appears on the screen
•
_sed`ca_ti_ningmi_htbe_n_CbecktheC_sed_Capti_nD_sp_ayc_nt_pane_intheScr_enmenu_
Chapter 5
25