Frequency Search Function; Receiving A Multicast Station; Multicast Station Search; Storing The Tag Information - Alpine CDE-HD149BT Manual

Frequency Search Function

You can search for a radio station by its frequency.
1
Press ENTER in Radio mode to activate the search
mode.
2
Turn the Rotary encoder to select "Frequency SEARCH",
and then press ENTER to enter the frequency search
mode. *
Operation is not required when Listen Mode is set to Analog (refer
to "Switching the listening mode" on page 27).
3
Turn the Rotary encoder to select the desired frequency.
4
Press ENTER to receive the selected frequency.
Note
• Press r in the search mode to cancel. Or, the search mode will be
canceled if no operation is performed for 60 seconds.

Receiving a Multicast Station

Multicasting is the Ability to broadcast multiple program streams over a
single FM frequency. This increases the amount and diversity of content
choices. A maximum of eight multicast station channels can be selected
on this unit.
Note
• Make sure Listen Mode is set to other than Analog (refer to "Switching
the listening mode" on page 27).
When multicast station is received, the program number
and the Multicast indicator lights up. Press  or  to
select the desired program service.*
Receiving the Multicast Station Program Service.
Program No.
Program Service example:
Multicast Radio
Program No.
Station
88.1 MHz
88.1 MHz
88.1 MHz
88.1 MHz
This operation can be performed only when Multi Cast Seek is set
to ON (refer to "Setting the Multicast Seek" on page 27).
12
-EN
Multicast indicator
Program Service
1 Main Program Service
2 Sub-program Service
3 Sub-program Service
|
|
|
|
8 Sub-program Service

Multicast Station Search

If a frequency has a Multicast station broadcast, the Multicast indicator
lights up. Use the Multicast search mode to select a desired program
from the Multicast stations available.
Note
• Make sure Listen Mode is set to other than Analog (refer to "Switching
the listening mode" on page 27).
1
Choose a frequency with the Multicast indicator on.
2
Press ENTER to activate the search mode.
3
Turn the Rotary encoder to select Multi Cast Search, and
then press ENTER to enter the Multicast search mode.
4
Turn the Rotary encoder to select the desired station, and
then press ENTER. The selected station is received.
Notes
• Press k VIEW at step 4. You can change the display between station
name, song name, artist name and program type.
• The search mode will be canceled if no operation is performed for 60
seconds.

Storing the tag information

iTunes Tagging lets you tag songs heard on HD Radio stations. You can
preview, buy and download later, songs from your iTunes tagged playlist
the next time you sync your iPod/iPhone. If the unit is connected to a
Tagging compatible iPod/iPhone, you can use the iTunes Tagging
function. For details, refer to the Owner's Manual of the Tagging
compatible iPod/iPhone.
The Tag indicator will light when a song playing on an HD Radio
station has tag information available.
Press and hold k/Tag to save its tag information.
If no iPod/iPhone is connected, "Tag Count X" is displayed (X is
the total amount of the tag information stored in this unit).
Notes
• During tagging, the iPod/iPhone takes priority to save the tag
information. If no iPod/iPhone is connected, the tag information is
saved to this unit.
• When the memory of iPod/iPhone is full, "iPod Full" and "Tag Count
X" are displayed. The tag information will be stored to the unit.
• If the operation is failed, "Cannot Tag" is displayed.
• This unit can store up to 50 pieces of tag information. When the
memory of the unit is full, "Tag Count50" and "Memory Full" may be
displayed.
• When an iPod that doesn't support the tagging function is connected,
"Non-Tagging iPod" may be displayed.
• When the iPod/iPhone is disconnected from the unit during tagging, its
tag information will be stored in the unit.
• If there is stored tag information on the unit, when an iPod/iPhone
supporting the tag function is connected, the stored tag information will
be transferred to the iPod/iPhone automatically. When the iPod/iPhone
memory becomes full, "iPod Full" will be displayed, and any remaining
tag information on the unit will not be transferred to the iPod/iPhone.
• If tag information already exists, "Already Tagged" will be displayed
when you try to tag information again.