Maytag MVWB950YG0 Use And Care Manual page 18

TROUBLESHOOTING
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call ...
in USA www.maytag.com/help - in Canada www.maytag.ca.
Fabric Damage (cont.)
Incorrect dispenser
operation
oL (overloaded)
appears in display
uL (unbalanced load)
appears in display
LF (too long to fill)
appears in display
Ld (too long to drain
water ) appears in
display
HC (Hot and Cold
hoses reversed)
appears in display
Sd (Excess suds)
appears in display
Liquid chlorine bleach may have been
added incorrectly.
Clogged dispensers or laundry,
products dispensing too soon.
Liquid chlorine bleach not used in
dispenser or Oxi Treat Stains option
not selected.
Load too large.
Load not balanced. The washer is
running a load-balance correction
routine.
Washer taking too long to fill.
Drain extends more than
4.5" (114 mm)into standpipe.
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm)into standpipe.
Hot and cold inlet hoses have been
installed incorrectly.
Excessive suds in washer. Washer is
running a suds reduction routine.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select FABRIC SOFTENER and/or OXl TREAT STAINS
options to ensure proper dispensing.
Load dispensers before starting a cycle.
It is normal for small amounts of water to be remain in dispenser
at the end of the cycle.
Homes with low water pressure may result in residual powder in the
dispenser. To avoid, select a warmer wash temperature if possible,
depending on your load.
Use liquid chlorine bleach only in the liquid chlorine bleach
dispenser.
You may only place Oxi products directly in the liquid chlorine
bleach dispener. If using Oxi products, be sure to select OXl
TREAT STAINS option. Do not use both liquid chlorine bleach
and Oxi product in the same load.
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Allow the washer to continue. If the dial is flashing and the
washer has stopped, redistribute the load, close the lid, and
press START/PAUSE.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "Installation Instructions".
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "Installation Instructions".
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Instructions".
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. If the
dial is flashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
.... dL (Lid cannot lock) An item in the load may be keeping Check for items directly under the lid.
appears in display the lid from locking.
lid (Lid opened) Washer lid left open. Close the lid to clear the display. If the lid is left open for more
appears in display than 10 minutes, the cycle will reset and water in the washer
will drain.
18