Programming The Playing Order Of The Tracks - JVC MX-KA3 Instructions Manual

Programming the Playing Order
of the Tracks
You can program the playing oMer of the tracks on all the CDs.
Note that you can only make a program when the CD Player is
stopped.
i_ You can program up to 32 tracks in any desired oMer including
the same tracks.
To Make a Program
1
Load CDs
2
In Stop mode, set the CD Player in Program
Play mode.
On the Unit
Press the PROGRAM button to light the "PRGM" indicator on the
display.
At the same time, "PROGRAM" appears on the display.
On the Remote Control
Press the PROGRAM/RANDOM button until "PROGRAM" ap-
pears on the display.
'Ihe "PRGM" indica/or also lights up on the display.
Each time you press the button, the display changes as follows:
PROGRAM -" RANDOM -" Blank display (Normal Play) "-_
(back to the beginning)
• lfa program is already made, the last step of the program will
be displayed.
3 Press one of the Disc button (CD1-CD3) to
select the CD you want to program.
The display will change to the Program Entry display.
orco, ,I,,,,, I,
"" __ I _-I_'_-'J
r
Disc number Track number
4 Select the track you want to program.
Using the Unit
While the display is blinking, press the 14141 or I_ID.t b u/lon to select
the track, then press the SET bullon within 5 seconds.
'Ihe program order number will be assigned fi-om P-L
o,,+ 2111 I
......
s',, , , P
%
Disc number Track number
I-- BP
Program order number
Using the Remote Control
Press the numeric keys to directly enler the track number. Then,
the program oMer number will be assigned from P-L
• To delete the current program step, press the CANCEL button
on the Unit.
Using the CD Player
5 Repeat steps 3 and 4 to program other tracks
on the same CD or the other CD.
5 To play the program, Press the CD 1_/11 but-
ton.
l_or details, see "To Play the Program You Have Made" men-
tioned below,
To confirm the programmed contents, while the CD player
is stopped, press the _ or I_1_t button on the Remote Control.
TO delete all the tracks in the program, while the CD Player
is stopped, press the • button.
TO Modify the Program, while the CD Player is stopped, press
the CANCEL bullon, the last track in the program is deleted. To
add new tracks to the end of the program, repeat above steps 3 and
4.
• If you try to program a track number that does not exists
on the CD, your entry wifl be ignored.
• If you try to program the 33rd track, "FULL" appears on
the display
To Play the Program You Have Made
Press the CD !_/11 button.
The Syslem plays the tracks in the order you have programmed
them.
• To use Repeat Play for Program Play, press the REPEAT but-
ton to select "ALL" or "I" before starting playback. For details,
see "Repeating Tracks" on page 15.
I_lYou can skip to a particular program track by pressing the I.,It_
or l,q_l button during Program Play.
I_lTo stop playing, press the • button once. if you press the • but-
ton, while the CD Player is stopped, the program is deleted.
To Exit and Re-enter Program Play
The program you have made is stolid in memory. So, you can exit
Program Play lemporarily or re-enter Program Play unless you de-
lete the program.
TO exit the program mode once, while the CD Player is
stopped, press the PROGRAM bullon on the Unit or the PRO-
GRAM/RANDOM button on the Remote Control to light off the
"PRGM" indica/or. By changing the source Io the other (e.g. Tun-
er), the CD Player also exits Program Play mode.
TO re-enter
Program
Play mode, press the PROGRAM or
PROGRAM/RANDOM button until the "PRGM" indicator lights
up again.
• Even when the power is turned off (standby mode), the
programmed tracks are not deleted So, you can re enter
Program Play mode.
14