Panasonic Omnivision VHS PV-4564 Operating Instructions Manual page 5

...Continued from page 4
A) If You Selected YES in _'_ _ '_ _ _ -steo4.
Select your f
..... SET CLOCK .....
1
PLEASE SELECT YOUR
cable box set up. CABLE BOX SET UP
_- i. o _ _- _| --
If you selected "CABLE VCR")CABLE BOX-_TV
BOX -_ VCR _ "IV", SELECTROTATE WHEEL
PUSH MENU KEY
continue with next step. L _)
PUSH WHEEL
If not, go to section "B" - ..............
below.
5
Then, set your
cable box
to PBS stationand then,
press the Wheel to go to
the next step.
ROTA17ETO SELECT
.ow,
PUSH TO
SET
to select and enter the
cable box output channel.
(The same channel you
tune your VCR to in order
to watch cable stations.)
..... SETCLOCK .....
PLEASESETYOUR CABLE
BOX TO YOURLOCALPBS
CHANNEL
NEXT : PUSH WHEEL
..... SET CLOCK .....
PLEASE ENTER CABLE BOX
OUTPUT CHANNEL
[fill W]
SELECT ROTATE WHEEL
SET PUSH WHEEL
END PUSH MENU KEY
If you use AudioNideo jack connections for
your cable box, select "VIDEO OUT" as the
output channel.
B) If You Selected NO in Step 4,
or if your cable box setup is:
VCR-_ CABLE BOX-_ TV
IIIOTATE TO 8ELIECT
Use N
PUSH TO
8lET
to select and enter your
PBS channel number.
i
..... SET CLOCK .....
PLEASE ENTER YOUR LOCAL
PBSCHANNEL
[I111 Ill]
SELECT ROTATE WHEEL
SET PUSH WHEEL
END PUSH MENU KEY
• AUTO CLOCK SET PROCEEDING
• AUTO CLOCK SET COMPLETED -----1
• The Iowset numbered channel OR
NOTE:
"Thescreen at fight appears
|t auto c|ock set is not
available for the PBS
channel selected (try another
PBS channel), or if it is not
yet available in your area, or
if an entry error was made.
AUTO CLOCK SET
IS INCOMPLETE
PUSH WHEEL TO SET CLOCK
If auto clock set cannot be performed, please
press the Wheel and set the clock manually as
described at right.
1
...Continued from page 4
ii ROTATE TO 8_LECT iiiii
m
SET
the set clock
See page 4 for Wheel
operationinformat on.
m
_,USHTO
SET
enter the month, ....... . ...
time, and D.S.T. (Daylight Saving Time).
• The day of the week appearsautomatically.
"DST: ON" automatically adjusts for daylight
savingtime. (See page 28 for details.)
..... SET CLOCK .....
llm!| trail =1 :lB BIt] ' J LfA
DST : ON
MENU TO CORRECT
PUSH WHEEL OR CLEAR KEY
to start the TO START PUSH M ENU K EY
Clock and exit this mode.
IMPORTANT NOTE FOR AUTO CLOCK SET:
Autoclockset willbe performedwhen the VCR isturned
offthe firsttime each day. If you use a cable box and you
want autoclock set to be performed, t he cable box must
be lefton at the time the VCR power isturnedoff. Also, if
the cable box controlsteps on page 17 have not been
completed,or yourcable box is not remote controllable,
the cable box mustbe tunedto your PBS channel.
See pages 6, 7 to change or re-enter
One Time Setup items
You will find out how to:
• changethe on screendisplaylanguage.
• replace channels in memory.
- set or reset the c_oG_ meLr_J_.
• set or reset the Auto G_ock Set _eature.
• add or delete a channel from memory.
Helpful Note
• It takes about 10 seconds for the VCR to determine
whether or not Auto Clock Set is available. Then,
depending on your local broadcasting company, it
takes from about 1 minutes to 10 minutes to set the
clock. If you would rather not wait, please press the
STOP button and set the clock manually.
5