Panasonic Omnivision VHS PV-4564 Operating Instructions Manual page 12

biuu ,_u,_bers/ leti.e_s (ex. K-II_[])cul[uspor_d with Iold-ouL Control Hefereulce L_ulde U_on[ pugu),
I_' Check list before you begin
[] If you are going to record from a cable box, please complete pages 16 and 17.
[] Connections are made (see separate Connection Guide).
[] TV and VCR are plugged in. VCR/TV selector is set to "VCR".
[] Clock is set to correct time.
[] Tape is long enough and the tape's record tab is in tact.
1
Press _ 1111 ,__/sT,., s,oPOH]
-lids "
" "/
for program mode. ,. _o_m_Y_ .......... pLP |
• If a program has already been - - -'" ,-'- /
BY ROTATING WHEEL /
set, select a blank program :PUSH WHEEL
[ ]
/
number with the Wheel. TOEND PUSH PROG
KEY
)
Rotate .o,...o,,,,_ ,' _. .
and ....
press _7o
to select and enter the date. (See example, below.)
Wheel DATE Wheel
Setting Down I Up
the Date ... WEEKLY(SAT),I---. 7 "-'_8--9 .... 31
-" 1
WEEKLY
(MON] Wheel Selection Order I
L__
WEEKLY(SUN)_ DAILY_ 6 ....... *"
....
Then,
in this same manner,c0_lnue to set the
Start time, Stop time, Channel, and Tape Speed
as they appear on-screen.
In step 2 of left,
ROTATE TO SELECT
U,e m
PUSH TO
,SET
to enter DALLYor WEEKLY
in place of the Date.
E / START STOP CH 1
h ....... |
I _¥R°TAT'NG _H_E_ /
Weekly recordings
require that you enter the
day of the week. See the
"Wheel Selection Order"
in step 2 on this page.
Then, continue
with programming.
r\DATI_ _TART STOP CH1
t-l,,,J=_;_'_ ...... l
I___J__>
....... __L__
/
I '" '" /
I BY ROTATING WHEEL /
/ :PUSH WHEEL_ /
L TO END PUSH PROG KEY J
i
10 maKe
corrections:
Press the Wheel or CLEAR button repeatedly to rnove
back or forward to the desired item. Then, re-enter it.
Press _ l_
to finish the program.
P DT START STOP CH SPD
2
3 .... :
4 : :,
SELECT 1-8:ROTATE WHEEL
ENTER :PUSH WHEEL
CANCEL:PUSH CLEAR KEY
END :PUSH PROG KEY
Press PFIOG
le.
Or,
repeat steps 2 and 3 to
set the next program.
5
Press _ IFI(orl_)
OFF to set the Timer.
The TIMER indicator J
lights in the Multi
Function Display.
"_ ..... I
12
Helpful Notes
If you are recording channels from a cable box,
the cable box must be left on for timer recording.
Also, if the cable box cannot be controlled with the
VCR (see page 17), you must manually select the
channel to be recorded at the cable box.
• Another way to review program contents is to
first, place the VCR in VCR mode. Then, press the
PROGRAM button while a Timer Recording is in
progress.
- Check your times carefully to avoid overlapping.
• If the record tab is missing at the time the VCR
power is turned off, the tape ejects and the Timer
indicator _ flashes.
If there is a power interruption of more than
about one minute, a timer recording cannot be
performed or continue.
If "PROGRAM IS INCOMPLETE" appears in
step 3, check all entries carefully and make any
corrections. Then, continue with step 3.
• When recording from an external source, rotate
the Wheel until "Lt (Rear connection)" or "L2 (Front
connection)" appears instead of the Channel.