Ultra Start 3250M Installation Manual page 9

PROGRAM MODE 3 - STARTER SETTINGS
Setting 1- Special Door Lock/ Unlock Operations
1 Type 1
2 Type 2
3* Normal Operation
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
1 Negative Input/ 30seconds
2 Timed Delay/ 15 Seconds
3* Gas/ Positive Glow Plug
Press the Program Button 2 time to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 Type 1
2 Type 2
3* Factory Re-arm
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
1 30 Min Run Time
2 45 Min Run Time
3* 15 Min Run Time
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 5-Maximum Crank Time
1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged
2 3 Seconds 2 Flashes
3*5 seconds 3 Flashes
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 6- Starter Kill/ Bypass Module Output- Orange wire on 14-Pin Con.
1Active Starter Kill 1 Flash
2Passive Starter Kill 2 Flashes
3*Bypass Module 3 Flashes
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 7- Safety Start Mode
1 Safety ON
2* Safety OFF
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
1 Flash Unlock before start. Lock pulse after start and shutdown
2 Flashes Lock pulse only after remote starter shuts off
3 Flashes No additional re-lock pulses
1 Flash Waits a maximum 30 seconds before starting.
2 Flashes Ignition ON for 15 seconds before engaging remote starter
3 Flashes Waits 2 seconds to start if no diesel input is detected
1 Flash Pulse after start and with lock
2 Flashes Pulse after start only
3 Flashes 0.75 second pulse with lock and after shutdown
1 Flash Remote Starter runs for 30min when activated
2 Flashes Remote Starter runs for 45min when activated
3 Flashes Remote Starter runs for 15 min when activated
3 sec Max time that starter will stay engaged
5 sec Max time that starter will stay engaged
On when locked, Before ignition and 2 seconds after ignition turns off.
Same as setting 1 but will arm 60sec after the ignition turns off.
Output before ignition. Stays on 2 seconds after ignition turns off.
1 Flash Must press the start button twice to remote start the vehicle
2 Flashes Press the start button once to remote start the vehicle.
9