Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
TECH SUPPORT
Western Canada 1 800 279-0636
United States: 1 866 698-5872
Eastern Canada Bilingual: 1 800 268-0683
E-Mail Tech Support: support@ultrastarters.com
Check Our Web Site: www.ultrastarters.com
Advanced 2-Way
Remote Vehicle Starter
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
WWW.ULTRASTARTERS.COM
See website for a full size printable version of this manual.
3250
3250
3250M
3250M
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part
responsible for compliance void the user's authority to operate this devise.
Advertisement
Table of Contents
Related Manuals for Ultra Start 3250M
Summary of Contents for Ultra Start 3250M
-
Page 1: Installation Guide
3250 3250 INSTALLATION GUIDE 3250M 3250M Advanced 2-Way Remote Vehicle Starter AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. FCC/ID Notice TECH SUPPORT This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: Western Canada 1 800 279-0636 (1) This device may not cause harmful interference, and... -
Page 2: Status Led
3250 Wiring Diagram Page 3 Pre-Installation Page 4 Components Pre Installation Check Installation Procedure Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 4 Pin Red Connector 2 Pin White Connector Jumper Selection Installation Page 6 Basic Installation - Quick start Auto Tach Learn Programming Page 7-9... - Page 3 Starter Heater Power Power Jumper Selectable Ignition 1 **** These connection’s are only necessary for installation’s on manual transmission vehicles. Always install a “M” Series Remote Starter on manual transmission vehicles. Note: Do not use the center pin of this connector to power relay packs. Doing so will damage the output.
-
Page 4: Before Starting Installation
Components - Control module - 2way LCD transmitter - FM Antenna with built in Program Button and LED’s - 6 pin main harness with dual 30amp power inputs. - 14 pin harness - 4 pin keyless entry harness - Hood pin safety switch - Under hood / window stickers - Installation guide - Owners manual... - Page 5 6 Pin Power Connector Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory off during start. 12 power 30amp input Constant 12volt power at ignition harness. 12 power 30amp input Constant 12volt power at ignition harness. Blue Ignition 1 30amp output...
- Page 6 Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Connect To The Vehicles Starter Wire. Green Heater Output Connect To The Vehicles Accessory Wire. 12 power Input Connect To Constant 12 Volt Power Source- High Current. 12 power Input Connect To Constant 12 Volt Power Source- High Current.
-
Page 7: System Reset
Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications. - Page 8 PROGRAM MODE 1 - USER SETTINGS Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 1 Flash Doors Lock / Unlock when the key is turned On/ Off 2 Ignition Lock Only 2 Flashes Doors Lock when ignition key is turned ON only *3 Ignition Auto Lock Disabled 3 Flashes Doors do not Lock or Unlock with the Ignition key...
- Page 9 PROGRAM MODE 3 - STARTER SETTINGS Setting 1- Special Door Lock/ Unlock Operations 1 Type 1 1 Flash Unlock before start. Lock pulse after start and shutdown 2 Type 2 2 Flashes Lock pulse only after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses...
- Page 10 PROGRAM MODE 4 - TACH SETTINGS Setting 1- Method 2- Low Idle Learn Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time. Step 2 - Enter Program Menu 4 - Press the # button on the remote.(Button #4). Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
- Page 11 Transmitter Programming 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON 2 - Press and hold the Program Button - Parking Lights will come ON **if the park lights do not come on at this point, turn the key off for 5 seconds, the repeat step 1. 3 - Continue to hold the Program Button until park lights go out.
- Page 12 Negative Type Door Locks Vehicle Lock To Control Lock/Unlock Relay or Switch Actuators lock Green Blue Positive Type Door Locks Vehicle Lock Lock/Unlock Fused +12V lock Switch Green Blue To Control Relay or Actuator 5 Wire / Reverse Polarity Type Door Locks Fused +12V Green Blue...