Advanced remote starters & vehicle security systems (16 pages)
Summary of Contents for Ultra Start 35 Series
Page 1
INSTALL GUIDE Covers All 35xx and 36xx Series Remote Starters REMOTE STARTERS CAR ALARMS ü WWW.ULTRASTARTERS.COM Technical Support 866-698-5872 ext 0 Support@ultrastarters.com -The system must be placed into Service Mode before any service work is started on the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 4 Recommended Installation Procedures Proper Connections - Remote Starters can handle loads of up to 30 amps for extended periods of time. It is critical to insure that all high current connections are properly soldered and insulated with quality electrical tape. Failing to insure proper connections will result in warranty being VOID and can result in damage to the vehicle and remote starter module.
Page 5
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 5 Wiring Diagram- 35xx Series YELLOW Starter Output (+) 30amp Output Heater/Acc Output GREEN (+) 30amp Output Power Input (+) 30amp Input Power Input (+) 30amp Input Selectable Output (+) 30amp Output WHITE Ignition Output (+) 30amp Output BLUE Factory Re-arm Output...
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 6 Module Side View Not Available Temperature Sensor Input Note: If the Temperature Sensor is installed the Cold Start Mode will operate by monitoring temperate. If the sensor is not installed the Cold Start Mode will function as Timer Mode. The temperature sensor can be installed under the hood strapped to the radiator hose to monitor coolant temperature or left mounted under the dash to monitor ambient air temperature.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 7 6 Pin Power Connector 6-pin Description Test For Wire 1-Yellow 30amp Starter Output This wire will test 0volts in off, accessory and in the ignition position.12volts during start only. 2-Green 30amp Heat/Acc Output This wire will test 0volts in the off position 12- 14volts in the accessory and run positions and 0 volts during start 3-Red...
Page 8
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 8 14 Pin Connector - Continued From Previous Page 11-Blue/White Tach A/C Tach Signal Input. Used to detect when the vehicle has started. This wire is connected to the vehicles coil, fuel injector or crank sensor wire. 12-Blue Glow Plug Diesel Glow plug input, detects both 12volt and negative...
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 9 Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow 30amp Starter Output 12volts during start position only. Green 30amp Heater Output 12volts in the accessory position off during start and 12volts during run.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 10 Manual Transmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected In addition to the basic remote starter installation.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 11 Auto Tach Learn 1) Turn the ignition key to the “ON” position. (The park lights will turn on*). 2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach signal is detected**, then after 30-35 seconds the park lights will flash and the horn (Optional) will honk twice to confirm Tach Learn.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 12 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process. Do not tach learn vehicle while the engine is in high idle. To ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 13 Entering Program Mode 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park lights will flash and the horn (optional) will honk to confirm entering program mode.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 14 Quick View Programming * See the following pages for more detailed programming instructions. Menu 1 -Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Horn Honk Type 1 Type 2 All Honks...
Page 15
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 15 Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Lock Button Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Honk Doors Lock/Unlock with Ignition key. 2) Ignition Lock Only 2 Flashes/Honks Doors Lock when ignition is turned ON only.
Page 16
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 16 Menu 2- Additional Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Unlock Setting 1 Secure Valet Mode - Length of time required to set the system into Service Mode 1) Secure Valet 1 Flash/Honk Hold the Program Button for 15 seconds *2) Normal Valet...
Page 17
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 17 Menu 3- Starter Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Start Button Setting 1 Special Door Lock/Unlock Operations (Factory Alarm Rearm). 1) Type 1 1 Flash/Honk Unlock pulse before start. Lock pulse after start and on shutdown. 2) Type 2 2 Flashes/Honks Lock pulse ONLY after remote start shutdown.
Page 18
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 18 Menu 3- Starter Settings - Continued From Previous Page Setting 5 Maximum Crank Time 1) 10 Seconds 1 Flash/Honk 10 sec max time that the starter will stay engaged. 2) 3 Seconds 2 Flashes/Honks 3 sec max time that the starter will stay engaged.
Page 19
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 19 Menu 4- Tach Settings Setting 1 Auto Tach Learn. 1) Perform a System Reset. See page 15. 2) Turn the ignition key on. (Park lights will turn on). 3) Start the vehicle, the LEDs on the antenna will come on when a proper tach signal is detected*. 4) After approximately 30-35 seconds the park lights will go out then will flash twice and the horn (optional) will honk twice to confirm that a tach signal has been learned.
Page 20
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 20 Service Mode ATTENTION: TO AVOID SERIOUS INJURY, this remote start system must be set into Service Mode before any under hood servicing is started. Service Mode will prevent the vehicle from starting while the vehicle is being serviced. It is the sole responsibility of the vehicle’s owner to place the system into Service Mode.
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 21 Transmitter Programming Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Button - The park lights will turn ON and the siren will chirp once.* Continue to hold the Program Button, the park lights will turn off and the siren will chirp 5 times quickly.
Page 22
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 22 Negative Type Door Locks 250ma Vehicle Lock To Control Lock/Unlock Relay or Switch Actuators lock Green Blue Negative Door Locks (More Than 250ma) Fused +12V Vehicle Ground Lock/Unlock Lock lock Switch Green Blue To Control Relay or Actuator Positive Type Door Locks...
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 23 5 Wire / Reverse Polarity Type Door Locks Fused +12V Green Blue Vehicle Lock Lock/Unlock To Actuator Switch lock Aftermarket Doorlock Actuators Ground Vacuum Type Door Locks DIAGNOSTICS Ground Fused +12V Green Blue Lock To Vacuum Pump...
INSTALLATION MANUAL REMOTE VEHICLE STARTER Page 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example when the start button is pressed the park lights flash 3 times slowly. Looking at the chart below this would indicate that the system is in Service Mode, simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter will begin to function as normal.