Warnings - Canon MP800 - PIXMA Color Inkjet Service Manual

Settings cannot be changed when
printing stickers.
Change the setting after removing the
card.
The card is currently write-enabled.
Set to read-only mode before
performing operation.
The paper size is not correct. Check
the page size you have set.
Failed to scan Photo Index Sheet.
Check the orientation, position and
marking. <See manual>
Failed to scan. Try again.
Film scanning error. Remove FAU
(Film Adapter Unit) protective sheet.
Photo scan error. Photo size is too
large. Leave at least 10mm between
photos.
Perform operation after the film is
scanned.

2-4. Warnings

Warning
Low ink
Print head temperature
rise
Protection of excess rise
of the print head
temperature
Restrictions on paper
Recommendation of the
print head alignment
(only on arrival of the
machine)
USB cable not connected Connect USB cable and turn on the PC.
Cancellation of trimming Reset trimming effect?
With Sticker print selected, the Settings
button was pressed.
With a memory card inserted in the slot,
change of the Read/Write attribute was
attempted.
With the memory card set to the Read/write
mode, Card Direct printing operation was
attempted from the menu.
Non-supported size of paper for PictBridge
Camera Direct printing is selected.
The machine failed in scanning the Photo
Index Sheet.
The machine failed in scanning the film. No
film was set, or selection of a film type (color
or black & white, positive or negative) was
wrong.
The optical volume was insufficient for
scanning the film. (The FAU protective sheet
was not removed, or the lamp itself was
defective.)
In cropping multiple photos at the same time,
since the space between the photos were not
sufficient, the photos were considered as a
single JPEG file, and the file became too
large.
After the PHOTO/FILM button was pressed,
printing was attempted from the menu
without scanning photos or films.
Message on the LCD
The following ink is low. Continue?
(Icon of each ink tank)
Yes No
In Camera Direct Printing, only "Yes" can be
selected.
If the print head temperature does not fall, the error
code "5200" is displayed, indicating the print head
temperature rise error.
If the print head temperature does not fall, the error
code "5200" is displayed, indicating the print head
temperature rise error.
The current paper cannot be set. Change the size
and type.
Head alignment required. Load paper and press
[OK].
Yes No
The error message is displayed for a while,
then the LCD automatically returns to the
display before the error occurrence.
The error message is displayed for a while,
then the LCD automatically returns to the
display before the error occurrence.
The error message is displayed for a while,
then the LCD automatically returns to the
display before the error occurrence.
Cancel printing on the digital camera.
Press the OK button to clear the error. The
LCD automatically returns to the display
before the error occurrence.
Press the OK button to clear the error. The
LCD automatically returns to the display
before the error occurrence.
Press the OK button to clear the error. The
LCD automatically returns to the display
before the error occurrence.
Press the OK button to clear the error. The
LCD automatically returns to the display
before the error occurrence.
The error message is displayed for a while,
then the LCD automatically returns to the
display before the error occurrence.
- Select Yes, and press the OK button.
=> Printing starts, and it is indicated on the LCD.
- Select No, and press the OK button.
=> Printing is cancelled, and the LCD returns to
the display immediately before printing was
attempted.
When the print head temperature falls, the error is
automatically cleared.
Note:
If the print head temperature exceeds the specified
limit when the scanning unit (printer cover) is
opened, the carriage does not move to the ink tank
replacement position.
If the print head temperature exceeds the specified
limit, an intermission is inserted during printing.
Re-select the supported paper type and size.
- Select Yes, and press the OK button.
=> Automatic print head alignment is done.
- Select No, and press the OK button.
=> The procedures on arrival of the machine are
finished.
Connect the USB cable.
With a trimmed image present, when printing on a
DVD or CD is attempted, the message is displayed.
1-9
Solution